How to save windshield moldings on Infiniti QX80 by Alfredo’s Auto Glass repair in Corona CA

How to save windshield moldings on Infiniti QX80 by Alfredo’s Auto Glass repair in Corona CA

[@Propotus]

I've had more luck pulling all of the clips along the drip rail as there are only like 5 or so per side. It takes a bit longer on the removal, but I don't need to be fiddly with the corner rail where it attaches to the drip rail. Love the quality information too! I like that you use the release tool on the top molding, however, I prefer to slide the top molding off by pulling it toward the passenger side. It keeps the molding from possibly bending. Tape is super helpful to keep from scratching the body.

[@KrisNativeThai]

Again, always putting out great contents. Thank you coach!

[@AlfredosAutoGlassRepairCorona]

Thank you 😊

[@marcusbarker5688]

Great video, always watch your video's, cameraman done good, also thanks for posting.

[@ronniescoggins4910]

Thank you so much for this video Alfredo!!

[@dubc73]

The dealership replaced the windshield on my 2017 armada. When I drive over 40, I believe that trim is rattling. It's very annoying hearing that inside of vehicle. Your video gave me an idea on how to replace the trim. Thanks man..

[@peterpauljames]

I been do glass for over 40 years molding always the heads is yet if you take you time you can save a lot of molding great job

[@brunosilvestre455]

Thank you Alfredo

[@blessedlife93]

These and FJS are my weakness

[@grady.stu.8300]

Fjs for sure..

[@michaeljamieson6974]

Thank you 👍

[@jamalnetflix2198]

Somewhere out there is a QX80 with two rattling flimsy corners from the first time I did one of these. Got em out fine but broke the clips on both from missing the holes. They’re holding on by double sided tape and the front trims. They’re also both bent a little from frustrations lol got better since then

[@jameschapman132]

great video sir

[@AlfredosAutoGlassRepairCorona]

Thank you!!

[@cybernan33]

Hola alfredo, un truco que siempre uso a la hora de salvar molduras plastica, grapas de plastico, etc es simplemente pulverizar con un bote de agua con el chorro fino para que penetre bien y al mismo tiempo levantando el material poco a poco para que entre el agua y solas van saliendo las grapas sin romperse, basicamente el agua ayuda a que los plasticos resbalen, prueba una vez y lo haras siempre, sobre todo en la parte de abajo aqui lo llamamos ovan, tipo mercedes, wolkswagen etc

[@CosmicGiggleMusic]

Alfredo: I hope this is helpful to you guys yes sir, this is all VERY helpful. My only wish is that your video library was bigger.

[@Catherine-gd3yu]

Hi Alfredo. Thank You for showing how you remove the molding. I just got my windshield replaced for my Nissan Armada 2017 and my uper molding it is mooving on the left side moore than on the other (when i press on).It mooves when i press on in with my finger in the midle. Do you think it is normal or it was not well installed? You think they maybe did not installed all the clips back? Thanks.

[@championwindshieldrepair216]

OG! God bless

[@AlfredosAutoGlassRepairCorona]

God bless brother🙏🙏🙏

[@markheist7875]

What double-sided tape do you use to replace the factory tape on the pillar finishing covers? Thank you

[@AlfredosAutoGlassRepairCorona]

After I release 3 clips of the top molding I slide it out towards the driver side.

[@deez4492]

what is the part number/name for that equalizer tool you used to remove the chrome upper molding?

[@manumusic2004]

Te aseguro que si haces los vídeos en español tendrás más vistas , ve a salomundo el cuando empezó a grabar sus videos en español fuen cuando se dió a conocer ,en ingles tenía muy pocas vistas

[@FormerDeathMachine]

Can I bring mine to you? The chrome molding is damaged from a previous owner and I’d like to have just one side replaced.

[@manumusic2004]

Saludos de México , en español por favor

[@AlfredosAutoGlassRepairCorona]

Claro que si!!

[@jackpuma9174]

I broke the white clip on the passenger side chrome molding. IT is right before that small bend chrome piece that goes to the front windshield. Do you have a part number to that white clip?

[@AlfredosAutoGlassRepairCorona]

Unfortunately they don’t sell it by it self. They make you buy the entire molding just for that clip, replace that broken clip with a Christmas tree clip same size hole, you’ll just widen where the molding holds the clip and slide it onto the molding.

[@Tempsho]

How destroyed would these mouldings get if you take it to a shop that doesn’t know what they are doing or don’t care. Why can’t all manufactures design mouldingless windshields lol. I guess they all can’t be as simple a an F150

[@MBS19812013]

Hey man, what is the corner molding you are working on at 0:28 to 0:32? I need that one as it disappeared

[@AlfredosAutoGlassRepairCorona]

Unfortunately they only sell that corner piece with the entire side molding.

[@MBS19812013]

@@AlfredosAutoGlassRepairCorona Do you have a recommendation where I could get the whole side molding along with the corner one? Is it only at the dealer? Do you know of a ballpark cost?

[@bradleymoore6539]

So I’m going to need the part number please

[@21Osopolar21]

Its a fancy Nissan armada

[@danielparker3432]

Just start popping from the back to the front and you can just skip this

[@Justin-eq2rc]

I think I want to work for you

[@edgaraleman6053]

Bro how much extra do you charge for this crappy truck design? A lot of work!!

[@tigerstriped22]

You hiring? lol

[@Bilalkhan-jj7ms]

Lolarm change

[@phillipcedeno152]

Music in the background makes it difficult to listen.

[@curtdawg4435]

My windshield was replaced and the whole top strip came off in car wash

[@TheCafeBoy]

Great video , but Infiniti ends with an "I" and not a "Y"

[@AlfredosAutoGlassRepairCorona]

auto correct 😂 I didn’t even notice. Thank you

[@AndrewFritschle]

Too much noise in the background.