hi i need the calibration of the motor caterpillar c-13 and the height of the injector thanks
@alimihi77477 жыл бұрын
thanks for this video if you help me how i can get a pdf document how adjust and inspect valve and injector
@kennethperian43702 жыл бұрын
Great job showing and telling, keep up the good work cause I am learning thanks again well see you next time see ya bye.
@Docoski7 жыл бұрын
Say, how many cat motors when #1 is on tdc both rockers are tight on the companion cylinder and vis versa? Is this mostly acert c15’s?
@usmanmechanics29504 жыл бұрын
sir i need cat c18 injyctor ajesment
@pablogrenade42407 жыл бұрын
I just traded my sweet obs 7.3 crew cab with munal trans, for a flat top freightliner with c12 in it that has a misfire ... its been very stressful as I need the truck, these videos have helped alot thank you
@valleyside60304 жыл бұрын
@AdeptApe Do you have to pull the jakes off to do the adjustment on a c13 ???
@Alex09922 ай бұрын
What happens if they forget the injector tool on there?
@davidspencer18924 жыл бұрын
I was wondering if you could add any information on a 3176 and how to install injector cups. Not a lot of information on these motors thanks
@robertwingate6503 жыл бұрын
If they are brass like the 3116, there's special tooling for removing and installing them. It's cheaper/faster to simply buy a Cat Reman head that already has them installed vs purchasing tooling to do one head. The brass ones are known to be. PITA sometimes.
@nealk63877 жыл бұрын
The 8 who put thumbs down work for cummins 😆
@bundylovess7 жыл бұрын
Top video mate big thumbs up
@AdeptApe7 жыл бұрын
+allan mitchell Thank you.
@ufohakunamaka60492 жыл бұрын
Thanks so much for this video and the many other you have produced . Really helpful to me as a diesel engine mechanic. Can this be done for C18 engine
@asokanarajun1859 Жыл бұрын
How can Tapit Setting CAT Generator C15
@asokanarajun1859 Жыл бұрын
How many clirance
@shortthrow502 жыл бұрын
My 2ks c12 cat manual does not mention injector height tool at all. And I have the yellow big injectors. Just says to go to zero lash and then 180 degrees and then that’s it. Can you explain? I have to put my motor back together next week and you saying to use tool is confusing me. What does the tool do? They don’t even make the too For c10 c12 or 13 upon research. Thanks in advance.
@AdeptApe2 жыл бұрын
You don't need a special tool. The setting is as you mentioned, zero lash plus 180° additional.
@jaredg55626 жыл бұрын
So what is the purpose of pre loading an injector? Thanks!
@robertwingate6503 жыл бұрын
The preload is to keep " lash" out of the valve train and prevent the injector plunger/barrel from hitting the mechanical stop when the injector lobe is on its base circle. If you look closely at the lobe profile for the injector, you can see that it has very agressive ramps on the lobe, any " lash" or looseness would be transmitted to the lobe and roller when the engine is at high speed, and would beat the parts to death over time.
@yusliermarrero98496 жыл бұрын
Hello sir i have a little problem with my cat c15 acert twin turbo my engine at idle rocks side to side and the sleeper cab shakes bad while idle and betting 12k rpm and 14k i replace the motor mount thinking it was the engine mounts but that didnt fix it any idea what could it be i mean the truck has power but it feel like and injector is not working right help me out with that man i can send a video of how the engine idle so you can see it moving side to side
@andrewlechuga43774 жыл бұрын
I used this info to adjust a c13 ...I want to donate 13 dollars.. Paypal still the same?
@garED16784 жыл бұрын
Sir how we can adjust the C15?, sorry i have a doubt so need to be turn agian to adjust the injector 6, 5 and 3?. thank you
@kenanahmad11104 жыл бұрын
An engineer, I have a 365 rig that heats up when you're working, if you let the engine work, it just doesn't heat up.
@automotivetechnologyinorom1160 Жыл бұрын
Thanks to my brother for this video to sher the skill for any technical activity on the machine.
@saheradera84327 жыл бұрын
what about3176
@sachinbidwai5 жыл бұрын
ok, what is the main reson to set injector height, if we not do then what will happen ?pls answer
@abdulafifi28843 жыл бұрын
very thanks to you because you make it easy for me. your videos very helpful.
@allaboutheavymachinery673 жыл бұрын
Thanks for this video Bro. Already subscribe.
@rudythebrownbeauty7 жыл бұрын
I have a C13 that one of the #5 cylinder push rods came out and landed safely horizontally along the vertical push rods. I was in a big rush to get truck up and running I am not sure which push rod came out? I put in back in and guessed on the adjustment to see if all would be OK. The engine started and is still running ok as of now. The rod that pop out did not bend and the one adjuster tip on that rod got a little nicked. The driver says all is good until he uses engine brake, the engine brake works, but the check engine light goes on and off when he runs the engine brake. I am about to go in and replace the adjuster and possibly the 5/6 engine brake solenoid pack and (run over-head) adjust all valves and injectors as your videos explains. Why did a push rod pop out? should I replace the engine brake pack for the number 5/6? Parts I got for C13 0LEE09239: 10R-2133 ARM AS Roker, 319-0271 Push Rod- Injector, 10R-6691 Actuator.
@AdeptApe7 жыл бұрын
+Rudy Salazar The pushrods don't usually fall out for no reason. The adjustment should be 15 thousands intake and 25 thousands exhaust. The rocker arm is possibly the cause, but my guess would be you have a bad lifter/follower/camshaft that increased the gap the pushrod and that could be the cause of it doing that. Look at that lifter the pushrod sits in very closely, you might want to pull the oil pan and take a look at the cam lobe for that cylinder as well. You may have got lucky and the pushrod may have fallen out, but my guess is you have another problem.
@jorgecarreno20473 жыл бұрын
Car C12: How can the cam follower be taken out without lifting the head?
@AdeptApe3 жыл бұрын
You can grab them with a magnet or coat hanger and hold them in the up position, but they can't be removed without removing the cylinder head.
@microtech.corp.22603 жыл бұрын
Anyone have manual book c13? Thank u.
@HusmHansh7 жыл бұрын
hi ..it's a good time to learn more about CAT 3412
@942doc13 жыл бұрын
Do you adjust c-15 injectors?
@derrickcotney88468 ай бұрын
Thanks for the information.
@ufohakunamaka60492 жыл бұрын
Thank you sir. Can this be done on C18
@pedrovanegas33824 жыл бұрын
How do you find the top dead center on a C10?
@asokanarajun1859 Жыл бұрын
How to Tapit Setting
@asokanarajun1859 Жыл бұрын
C15 CAT Generator Tapit Setting T
@joellagpacan93407 жыл бұрын
Does this technique also apply to the JEP C15 and KRA C15 engines?
@AdeptApe7 жыл бұрын
+Joel Lagpacan Those are high horsepower engines for military applications usually. Do they have the four wire pin or two wire?
@jonathangraber819 Жыл бұрын
Awesome job, thank you
@TheRebelOne.7 жыл бұрын
I enjoy your video's Adept however I have to ask this question. As you work for CAT do they not question the fact that you are giving away mechanical information that could potentially harm their business?
@AdeptApe7 жыл бұрын
+0BMM1 I have never had a Cat representative message more or anything to say that. I did have someone comment that they were doing some sort of Caterpillar service information survey and they found my videos helpful. I'm not really giving any top secret info out, just the proper way to do things. I figure that if you own a Cat its nice to have the info out there to perform some of the maintenance yourself if you want to and it makes a better owner, I wouldn't want to own a car that I couldn't at least do maintenance on myself.
@billshewmake96605 жыл бұрын
@@AdeptApe thanks for your videos. Been very helpful with my 3406e
@JohnJohn-rb7kg5 жыл бұрын
No 1piston is tdc so how many injectors can be adjust, Thanks
@Celebrity_Fever2433 жыл бұрын
Injector # 5,6,and 3
@armanamat29966 жыл бұрын
Bro c18 set TIMING is it same
@Chamnan-yk4sb11 ай бұрын
❤️👍
@Jerseytrucker9117 жыл бұрын
hey man, quick question how reliable are c12 engine and what is the max hp it can e set to.. thanks for the feedback in advance !!
@AdeptApe7 жыл бұрын
+Mrvmtm The C12 engine is a reliable and simple engine. Single turbo, pushrods, no emissions items. Now the horsepower can vary greatly based on whether the engine was an RV engine or not. The RV engines with a C12 could be 400+ hp, but a truck version is usually much less. If you know the serial number of the engine you are looking at I can tell you the max horsepower for it.
@Jerseytrucker9117 жыл бұрын
thanks for the quick feed back, will get the info. thanks again!!
@JasvirSingh-rc2ig2 жыл бұрын
Thank you for informin
@anantapatil96275 жыл бұрын
Can i try this setting for c18 engine
@mzee55337 жыл бұрын
Easy one Adept nomore expensive tools big up bro
@AdeptApe7 жыл бұрын
+Muchie Thank you.
@albertomendez12905 жыл бұрын
U the are the best dude! tanks
@chekelley68617 жыл бұрын
What's the purpose of torque striping? Is it to remind yourself that you hit all of them?
@AdeptApe7 жыл бұрын
+Che Kelley I usually tell the new the paint locks the bolt/nut in place, but that is just to mess with them. It is really to say "this one is done" so if it's an adjuster then it has been adjusted, if it's a bolt them it had been torqued.
@mrbuck50593 жыл бұрын
C11 Acert
@troyjenkins20127 жыл бұрын
Just put a new head on a c12 in a t800. Your videos were a HUGE help. Thanks a lot
@AdeptApe7 жыл бұрын
+troy jenkins Thank you for watching them.
@BASUKA234 жыл бұрын
If am doind an over head on a mxs engine do i need the high tool?
@huemungus72974 жыл бұрын
Yes
@BASUKA234 жыл бұрын
Thanks
@kwmiked7 жыл бұрын
u ever do a video on a cam change on a c15? i don't off hand remember seeing one?
@AdeptApe7 жыл бұрын
+kwmiked I haven't done a video on one yet, there are a few rebuilds in the shop though so I'm hoping to get some good videos out through the end of the year.
@silveriogarza21776 жыл бұрын
Kwmike-D / t
@abdulrahim45705 жыл бұрын
very good video
@byronmcgowen7 жыл бұрын
how do you shim the check valve regulator or fuel pressure on an acert C15
@AdeptApe7 жыл бұрын
+Byron Mcgowen I've never heard about shimming the regulator, the regulator is on the fuel filter housing though. If you watch my fuel pressure troubleshooting video it'll show where it is.
@byronmcgowen7 жыл бұрын
send me the link
@AdeptApe7 жыл бұрын
kzbin.info/www/bejne/jpLYgal9isdsias here you go
@TheFisnikbojku7 жыл бұрын
does this work on my c15 acert
@AdeptApe7 жыл бұрын
+fisnik bojku Nope, I believe you have an MXS so you'll need the height tool, which if you watch the C15 overhead it discusses that.
@pjwalchshauser15146 жыл бұрын
I have a C12 2KS. 365000 miles. What would cause a slight flutter , not necessarily a miss, just between 1300-1500 RPM? No smoke noted. Any input would be appreciated.
@dawoodkhandiesellab14945 жыл бұрын
Nice video
@Celebrity_Fever2433 жыл бұрын
Superb
@salvadormassaky2076 жыл бұрын
Hi. I have been following your tutorials videos a long time ago because of the accuracy and professionalism of their content. But now I am confused about a topic which is the following: I will install the cylinder head on a c15 acert sdp engine and i need to know if I need injector height tool or not. The serial number is sdp104..also the torque specs for the studs of the compression brakes and rocker arms and vva's I really appreciate your information Thank you Merry xmas
@angelsonny14693 жыл бұрын
i know Im randomly asking but does any of you know a trick to log back into an Instagram account?? I was stupid forgot the login password. I would appreciate any help you can give me!
@garyira68573 жыл бұрын
@Angel Sonny Instablaster ;)
@angelsonny14693 жыл бұрын
@Gary Ira thanks for your reply. I found the site thru google and im waiting for the hacking stuff atm. I see it takes a while so I will reply here later with my results.
@angelsonny14693 жыл бұрын
@Gary Ira It worked and I now got access to my account again. Im so happy! Thanks so much, you saved my account !
@garyira68573 жыл бұрын
@Angel Sonny You are welcome xD
@ephraimpalces43367 жыл бұрын
sir what about C11 acert
@chucofilms9155 жыл бұрын
Do u really need a lil microphone and a golf hat cmon now lol