How to set the laser timing in ezcad2

How to set fiber laser timing in ezcad2.
This is an example of how to setup a test pattern so you can tweak the laser firing timing to get the cleanest engraving you can.
Sorry for the poor focus on the engraving. I will try to do better next video

[@ozziesoto2955]

Awesome information and easy to comprehend. Your great teacher!!

[@Carl246us]

First of all I want to thank you for these great "How-To" videos on these Fiber lasers. You are saving a lot of folks a lot of time. I just got mine and it looks just like yours. It's a 30w. I see that you seem to have yours in a garage. The paperwork I got is conflicting. It says it will operate in harsh environments but it also says it must not be kept in a higher humidity environment. I have set mine up in my house in a spare bedroom. Do you see ant reason that is a bad idea?

[@ajimachining2537]

I have mine in my shop bay. No AC in Florida (Miami), so high humility in the summer. I have not had any issues in 4 years that I have it.

[@Sanjeewa.Subasinghe]

good video❤

[@mikeadams9859]

THANKS FOR YOUR HELP BY SHOWING WHAT YOU HAVE ALREADY LEARNED. MY QUESTION IS WHAT DOES IT MEAN/HOW TO FIX THE ERROR MESSAGE INVALID HANDLE ? THANKS

[@ajimachining2537]

Email me [e-mail] I will send you my phone number so you can call me I do not understand your question

[@MiguelGomez-rc7ou]

Marvelous explication!!! If you will engraved wood, what setting you use? I get burned wood or not engraved I know the fiber laser aren't the best for engraving wood, I just need engraving some texts

[@ajimachining2537]

I have not done wood because I have a co2 for that. All I can say is experiment with scrap

[@RahulSingh-ox5vd]

What is use off ENDTC our poliyogo

[@Angryhelder]

What is your recommendation on the hatch settings for doing stainless steel? My markings are brown instead of black, thanks in advance.

[@ajimachining2537]

Try uni directional (not zigzag), higher frequency and slower speed. .01 spacing on the hatch and raise the focus a little. You don't want to burn the stainless, you want to heat it.

[@Angryhelder]

@@ajimachining2537 Will do that thanks. Might I suggest a video idea? How about doing photo engravings on Stainless and other materials. Maybe ABS plastics as well. Thank you.

[@ajimachining2537]

@@Angryhelder i will put them on the todo list.

[@TheSlugSea]

👍

[@MarkWaples]

So it pays to create a table of Laser timings if you wish to laser at different speeds - what is the rationale for only lasering at 1500? Curious and thank you for the information :)

[@ajimachining2537]

For me 1500 works as a good all around setting for what I do so I don't have to keep changing it.

[@MarkWaples]

@@ajimachining2537 thank you for the reply - after peforming a few tests I have arrived at a good setting for the timing - thank you for the inspiration to check mine

[@truthbtold5690]

Will this fix the issue of uneven engraving where some part of the picture is lighter than other areas?

[@Aj-sx2km]

It might depending on the size and speed.

[@paulriley5940]

Do you set the timing and delay for each speed?

[@Aj-sx2km]

You might have to if the speed is a drastic change

[@airborne448]

Minute 2:55 where do you find the setting of your machine mine is a raycus 50w

[@ajimachining2537]

Should have a data tag on the power supply

[@ajimachining2537]

Sorry I Misunderstood your question this is trial-and-error to get a setting that works for your laser

[@liiiiilian]

What does this sentence mean? demo version only for evaluation

[@ajimachining2537]

The software is running without the security key so it is restricted to a demo version. It can not save files when in demo mode.

[@jesusrangel4973]

I need help fixing my laser settings, it’s not engraving what I have on screen it engraves random lines.

[@ajimachining2537]

Did you ever get this figured out?

[@numankhan428]

Sir ! I need your help ..

[@numankhan428]

I have 50 watt laser engraving machine

[@numankhan428]

But I have a little problems ..if you have watsapp or messenger .then plzzz give me your number ... I shall be very thankful to you .. on this way I will show you my machine and I can learn from you .. how to use it

[@numankhan428]

Sir what should I have to do for a deep Marking .. I keep 100 power but it mark light not deep .. what should I have to do

[@califlet4888]

Numi Khan did u figure it out ?

[@tdimop]

To bad EZCAD doesn't have a computer algorithm that changes the on off timing in relation to the speed after you complete a timing check. Sure it's all just math... lol