How to straighten bike wheel. Fix Rear bicycle Wheel

[@GoodBicycle]

Thank you for your SUBSCRIBE ! 😘❤❤❤

[@caniloup]

Nicely filmed, as always! The only additional suggestion I have: whenever I check the lateral run out of a wheel, I do firstly check if there is also a noticeable radial offset that needs to be corrected. Best wishes!

[@GoodBicycle]

thanks for the advice ! 😘

[@Gledii]

thanks for sharing. look, i centered my wheel (as best as it gets with zip ties) but after putting the tyre back and pressure i had to adjust it again. i was sure that the tyre was perfectly placed. is this "normal" or the wheel should keep true after inserting the tyre and pressure? thanks a lot!

[@GoodBicycle]

Make sure that the wheel is standing flat on its rim. If it is uneven because of the tire, then the problem is in the tire itself, try deflating the wheel, leveling the tire with your hand and inflating it again until it is evenly on the rim

[@EleanorPeterson]

I'm certainly not an expert (😁), but it may also be worth checking that the overall spoke tension is high enough. A wheel that's perfectly true in the jig, but without enough tension on the spokes (I think it's about 100kgf for the common 1.8mm steel spokes) can be pulled out of line when the tyre goes back on, especially if the tyre itself isn't perfectly round and even. Most ordinary tyres are a bit wobbly, so the straightened wheel needs to be stiff enough to hold its shape against an uneven tyre. A professional spoke tension gauge is ridiculously expensive (£1,000+) if you're just a regular cyclist, but there are plenty of very good but much cheaper (£85) versions or, if you're wiling to take a risk on quality and precision, one of the really cheap copies (£15) is better than nothing. (They look exactly like the one shown in this video.) Getting the tension 'near enough' is fine for most non-professional riders, and even the cheapest gauge will help by ensuring that the basic tension you settle on is consistent and (probably) not too low, even if the exact figure isn't accurate. When the straightening is going well, it's easy to forget that the overall spoke tension may be dropping as you work. It's depressing to create a lovely straight rim that's too slack and to have to start all over again! A lot of wheels straightened at home are not stiff enough because it's hard to 'guesstimate' the right spoke tension without a lot of experience. Even if a slack wheel holds its shape when the tyre goes back on, it won't stay true for long once it's back on the bike and you start riding. Good luck! 🙂

[@rhecoy2007]

I can do that if I have the tools but it’s not worth to buy the tools coz of its high price here in our place. And the are some bike shop where we can just pay for some bike works and the price is not high. I also appreciate the talent doing the bike aligning works😮

[@GoodBicycle]

Thank you for your comment! I try to make interesting videos

[@notundermywatch3163]

You don't need a trueing stand, you can do it with only a pair of zip ties and a spoke wrench costs less than 5 dollars.

[@MarcosAlejandroGomezgarage]

Que modelo es tu centrador? Y que tal te va con el? Hay algi que no te guste de tu centrador? O va perfecto?

[@GoodBicycle]

No puedo decirte el modelo, no me acuerdo. La máquina es como una máquina, ordinaria. Cumple su función. Estoy satisfecho con esta herramienta.

[@MarcosAlejandroGomezgarage]

@@GoodBicycle para el salto vertical no tiene?

[@GoodBicycle]

en otro momento))))

[@cosmefulanito5933]

Having the necessary tools, it is very easy. Now make another video explaining the same thing but without using those tools that no one has at home.

[@GoodBicycle]

This belongs to the category of "inventions"😊

[@Gledii]

you can use a zip ties. search for it in youtube and you will find

[@xSergooo]

Вот без слов всё ясно и понятно👍. Можно научиться, но некоторых инструментов🛠, как тензометр редко в наличии у простого пользывателя велосипеда. И вообще сегда мечтал научиться ровнять колёса на велосипеде.🚲

[@GoodBicycle]

Thank you for your comment! ❤️❤️❤️ Share this video with your friends, it will help the development of the channel! 📈😘

[@Valatrius]

Wo hast du diesen Speichenschlüssel her? Weiß nicht wie es übersetzt wird 😊 ich meine den kleinen Gabelschlüssel Minute 4:34

[@GoodBicycle]

Dies ist ein Speichenschlüssel. Sie können etwas ähnliches in Online-Fahrradgeschäften finden, wie bike24

[@Slawek_EU07]

These alu rims are on most bicycles used in my country, Poland. Steel rims have greater durability.

[@GoodBicycle]

Thank you for your feedback! 😘

[@TIZIANOBERNARDINELLO]

Ma questo ci mette un giorno per ripristinare una ruota

[@GoodBicycle]

Ogni volta la riparazione sarà accelerata 👍

[@petkobinka8722]

Super super BRAVO 👍👍👍

[@GoodBicycle]

Thank you for your comment! 😍 If you liked my videos ❤️, support the channel financially 💰🙏. Use the "Sponsor" function on KZbin ✊😘

[@andrzejkwiatkowski5453]

co w przypadku "bicia" góra - dół ?

[@GoodBicycle]

Na tym kole zadanie polegało na naprawieniu "8".

[@niar-f-exon738]

Me quito la gorra carnal, me sorprendiste!

[@GoodBicycle]

¡encantado de ser de utilidad! Gracias por sus comentarios 😘

[@niar-f-exon738]

@@GoodBicycle Y he querido aprender porque ando mucho en bici y quiero aprender a alinear rines.

[@GWClightsandsounds]

Is this your new channel mate?

[@GoodBicycle]

yes ) live version

[@marcinantosz5034]

Super. Dziękuję.

[@GoodBicycle]

Dziękuję za komentarz! 😍 jeśli podobał Ci się ten film, udostępnij ten film swoim znajomym ❤️ pomoże to w rozwoju kanału! 📈

[@stefanovessicchio1502]

Bravissimo!! Grazie! ❤

[@GoodBicycle]

E grazie per il feedback

[@ahmadghanm]

Well done mate!

[@GoodBicycle]

😘👌

[@edreessarwary1992]

Nice job

[@GoodBicycle]

😘 thank you!

[@edreessarwary1992]

You’re welcome ☺️

[@GoodBicycle]

🚀

[@adoonii4725]

hello from Bosnia

[@GoodBicycle]

😘👋

[@HàBùi-e7x]

❤

[@GoodBicycle]

❤❤

[@edreessarwary1992]

👌👌👌

[@GoodBicycle]

💁❤️

[@edreessarwary1992]

🥰🥰🥰

[@GoodBicycle]

🚀

[@francescoiannucci1689]

Ssi capace di farlo senza gli strumenti da officina? Io si

[@GoodBicycle]

è possibile))))))

[@BrainFreezeSuperheated]

ASMR ❤

[@GoodBicycle]

😊

[@eggbenedict-gt7mw]

Why do they make cheap rims that bend, and they want to go to moon 😂😂😂😂,

[@GoodBicycle]

To ensure that bike shops always have work 😊

[@granthardy3550]

That is a horrible noise to hear on a bike, any rubbing against the rim. I would just increase the gap to the brake blocks, I think you need too many expensive tools and expertise to attempt it yourself.

[@GoodBicycle]

everything can be fixed!))))

[@stevengagnon4777]

​@@GoodBicycleAlmost !

[@GoodBicycle]

😉

[@Marfi645]

Thank you 🫵 Oi...👁️👁️

[@GoodBicycle]

thank you for your comment! 😘

[@kristianvrum8979]

A word of warning: despite the large quantity of parts this dude is surrounded by, he is clearly an amateur.

[@GoodBicycle]

and what did you want to see more of?

[@lexthang]

How so?

[@stefans.3197]

👎👎👎

[@GoodBicycle]

❤ ❤ ❤ )