How To: Whirlpool/KitchenAid/Maytag Microwave Door Torsion Spring WP4452395

[@vpernell]

Absolutely fantastic video! You did it step by step and made it very clear to everyone what you were doing and how you were doing it. One of the best instructional videos I have ever seen! You should get an award for this! Thank you so much!!!

[@mikeokeefe5994]

Wow! this video saved me. I could NEVER have figured out how to do this without the excellent methodical approach to changing the springs. Many thanks.

[@phpkerouac]

YES YES YES! This was a great video, thank you very much for making it. On my repair, I didn't have to remove the panel at the top, nor did I have to slide the microwave out if it's installed enclosure. I could access all necessary screws to get the door off and replace the torsion springs easily. Thanks again!!! (the other spring part for this model is WP4452396. I got both springs on Amazon.

[@appliancepartspros]

We're glad we were able to help you repair it!

[@BOHICA_]

I have the same looking micro/oven combo. I didn't have to take out the microwave either.

[@szsven]

Very well done video, thanks! I didn't remove the control panel or lower oven door, but I did pull the microwave out about an inch to get to the aforementioned "pesky screw" under the door. I had to play with the springs a little to get them to seat properly, but you'll know when they're right. Whole job took about an hour, but half that time was spent cleaning the greasy grime off the vent and inner door frame.

[@timphillips699]

Same here. I left the control panel, upper vent and lower door and didn't have any issues except not paying more attention to how/where the hook side of the spring was when I removed it. Had to watch that part of the video over and over till I figured out my mistake.

[@queenegreene3926]

Thank you for your comment. It is very helpful. This video is clearly misinformation.

[@pooshd]

Great video, thank you. I just replaced my torsion springs and also was able to do it without removing the control panel and pulling the microwave out, as some others here had mentioned as well.

[@queenegreene3926]

Thank you! This video takes users through UNNECESSARY steps.

[@tedwalker2130]

I have a KitchenAid wall microwave. This video made the job of replacing the broken spring easy. Thank you!

[@j.davidsemple6988]

Your video is great. Not sure that I could have done it without the step-by-step video. Was able to replace a broken right hand torsion bar on my stainless combo. They took a shortcut on the SS model making one spring very stiff. Second time it has broken in 20 years.

[@peterradsliff527]

You provide a tremendous public service. I’ll be sure to buy from you in the future.

[@aerlial360]

Excellent as always. Thank you. Mine is a whirlpool Gold but uses the same part # plus WP4451009 for the other sping . People need to know there are two springs.

[@ironchefw]

Thank you. Replaced both springs. They can be a little tricky to fit in their place. I did the whole job with cleaning in about 30 minutes. Was able to do mine without removing control panel or pulling micro out. And now I know how I can clean the glass in the future.

[@appliancepartspros]

You're welcome!

[@aquarianuw]

Do you mind sharing how you removed the 2 screws on the bottom of the door trim? One of them is blocked from the metal vent of the oven below in mine.

[@jonathannovember3776]

Great video! I'm about to order the parts from you to replace the springs on my KEMC378KSS03. My unit has a chrome trim piece on either side that goes from just under the control panel to the bottom of the oven. In your video, that piece was not on the unit, so all of the screws were easily accessible from each side. How do you remove the chrome trim pieces? Thank you.

[@Kriesinator]

I'm wondering about the same thing... I'm guessing it just pulls straight off because there is no way to slide it up or down. Have you gotten up the courage to try pulling it off?

[@dpky7333]

Each trim piece has a screw 4 inches from the bottom that is visible when the oven door is open.

[@pcorn23]

Are these the parts that make sure the door doesn't slam open (provide resistance)? Or is there an actual spring that allows the microwave door to open and close without slamming? Thanks

[@yukuhana]

I was wondering the same but after seeing them replaced in the video, it dawned on me the "spring" action is achieved by twisting the 2 rods as the door is opened and closed.

[@cristinamcnatt4359]

I have a Whirlpool Gold combo woc95ecoas03- The door will shut, but when I put in the cool time it won’t run unless I hold the door closed tighter. Will replacing the door torsion spring most likely solve that problem?

[@nisapasamoot8043]

Thank you very much!! This is really neat! Because of your video, I was able to detach those wires from the unit before installing a new KitchenAid wall oven/micro combo.

[@Travis-h6c]

I am working on a Kemc307kss03, but the diagram only shows 1 torsion spring. Is your video based on the 308?

[@appliancepartspros]

WP4452395 is for the left side and WP4452396 is for the right side torsion spring. You can place an order through our website, or you can call us at 1-877-477-7278 to place an order over the phone.

[@hortmeister]

Great instructions. However, was unable to get microwave to pull out of our KEMC308. We followed each and every step and also removed the 2 screws holding microwave at bottom. The left side will move some, but the right side seems to not give as if there is another screw or something holding in place on the right side. Anyone else run into this or know what may be preventing the microwave from being pulled out?

[@lawrencepines4346]

Which torsion rod exactly is the "left" and which one is the "right"? I think mine failed on the lower right corner, the rod that goes from lower right to upper left. Which one is that? I want to order the correct spring rod because the other one that goes from lower left to upper right looks fine. Thank you very much.

[@appliancepartspros]

What is the model number of your microwave?

[@lawrencepines4346]

KBMC140HSS04

[@lawrencepines4346]

This broken torsion rod sits forward/outside the other rod as it crosses the outside of the door.

[@mikekoch9040]

Super Video my wife and I disassembled as shown. All screws could only be removed as per the video. Wish I could have run it in reverse to re assemble LOL but we figured it out and cleaned all the glasses even in the oven door. Thank you so very much, it was a great help.

[@appliancepartspros]

You're very welcome! I'm glad that we could help.

[@randalzoeller7696]

I have KitchenAid KEMC308KSS0 in stainless steel. What are the exact two part numbers I need to order for right and left torsion springs? The information I'm seeing is contradictory and says WP4451009 and WP4452395 are not to be used with the stainless steel models as they require a stronger spring.

[@danm3188]

Do all springs like these fail regularly? The ones on my Kitchenaid have failed every year or two and going on 10 years, all those springs really add up.

[@sbearly]

We've had ours 18 years. First time one broke was 3 years ago. Then just a week ago. It broke when my daughter was cleaning the inside of door when it was down. I think she was pushing hard on it. Perhaps when cleaning we should be holding the door slightly up with one hand so as not to put pressure on the springs.

[@Rudeboy916209]

So these torsion springs are supposed to bring the microwave oven door to close position?

[@Dubghost420]

whirlpool rmc275pvs00 I need to know how to change the door switches on the microwave part

[@buddhismkids2522]

How do I replace the porcelain clip that holds the broiler element in place? I have a KitchenAid Microwave (part number is W10909479). The clip is broken and and the broiler element is half hanging down. I can't use the microwave.

[@mikemeechan5640]

Just finished my replacement. I was also able to do it without removing the control panel and pulling the microwave out. I did remove the oven door just to get it out of the way and ease access to the screws that need to be removed on the bottom of the microwave. One TIP regarding removing the screw seemingly blocked by the vent: If you look in the vent there is a screw head protruding from the bottom. That screw is there to hold the vent in place horizontally...it is not tightened. If you lift up slightly on the vent the screw head will drop below the vent and you will be able to move the vent horizontally to the side to expose the difficult screw to reach. The entire job is kind of tedious but not difficult. Just pay attention to how the tension rods connect before you take the old ones out and take some photos of what they are supposed to look like after they are installed.

[@appliancepartspros]

Thank you so much for the feedback! We are so glad you were able to complete the repair. If there is anything we can help you with in the future please let us know.

[@thehappygnome]

We really appreciated this video. We wish there were better closeups of the hinge installation. The presenters arms got in the frame during a crucial part.

[@appliancepartspros]

If there is anything we can help you with please let us know.

[@sofia-bq4kv]

Can the microwave be detached completely from the frame?

[@Resist_JWO_1984]

Nicely done. Thanks for the walkthrough.

[@mahvish.k]

Loved this video - made it so much easier! Thank you :)

[@onestepcloser2162]

What is the problem when Pain appears on the Door locked screen

[@kwd57]

I also did it without removing the microwave oven. The only problem is the left screw on the bottom of the door, which is above the rectangular vent. I took a 1/4 inch #2 phillips bit and ground it short and left just enough of the 1/4 hex to turn with a small 1/4 inch wrench, with the door open.

[@victoramona4902]

Thank you for a great video!

[@AG-wn8tc]

Thank you!

[@appliancepartspros]

You're welcome! Good luck with your repair and let us know how it goes!

[@davidmudie2147]

Tip: replace that pesky screw under the vent with a hex-head screw. Will make it much easier if this happens again.

[@sonichuizcool7445]

Door still falls after replacement

[@appliancepartspros]

What is the model number of your microwave?

[@henrywhsu]

DO NOT REMOVE THE LOWER OVEN DOOR!!!! Not only is it unnecessary, it is extremely difficult to reset the door back in. I spent more time on the lower oven door than the rest of the repair. And it is totally unnecessary.

[@queenegreene3926]

THANK YOU, THANK YOU, THANK YOU! This video is NOT helpful considering the Microwave does not need to pulled out, NOR does the lower oven door need to be removed. Terrible DIY video.

[@queenegreene3926]

There are TWO white plugs on the Control Panel. You failed to indicate WHICH of the two white plugs to disconnect. ALSO, your video illustrates many unnecessary steps such as removing the Control Panel. Won't be watching your "How-To" videos based on your misinformation.

[@appliancepartspros]

We apologize that the video wasn't helpful for you. Our videos are just to help give a general idea on how to do the repair. Our videos are not model specific. If there is anything we can do to help you out please let us know.

[@queenegreene3926]

@@appliancepartspros don't apologize for the misinformation. Correct it and re-post. This can be critical when repairing electrical appliances since a "general idea" can be interpreted by the viewer as gospel...the proper and ONLY way to do the repair. Do the right thing Appliance Parts Pros!!!