HP PRODESK ➔ GAMING PC?! It's HARDER than YOU THINK!! [2020]

[@shahtayyib]

they seemingly hate people recycling old PC's. shame.

[@tytyguy1able]

I dug a 4th gen prodesk out of the dump. Tossed some expansion cards, a dual ssd 3.5 bay and a couple of 3.5" drives for a killer little NAS. great value and surprising modularity

[@yuan.pingchen3056]

The MODEM dial-up sound effects drive me crazy, good job dude... LOL

[@PDog69]

Good commentary man good video

[@tompeters4234]

HP ProDesk's can be had for a good value. I was updating a ProDesk 600 SFF i7-6700 so it could run a biking simulator for someone. Finding a Low Profile, that does not need 6pin power, and hopefully not draw too much power for the baby SFF power supply. The simulator is good with a GT1050 LP which I paid $125 on ebay. Finding a LP card that would fit before the USB plug was quite the challenge. I haven't got it yet, it's last scan Dec 23 was a post office 30 miles away, and it's 'stuck'. You video has me more scared that this adventure is going to hit more snags.

[@yasugi0153]

I believe the gtx1650 LP fits

[@teaeco]

when you use an hp ProDesk intel i3 with a dell monitor now you're living my budget life

[@yasugi0153]

Thank you for Making these brackets available to purchase I ordered one of these on a whim and plan to tinker on it and upgrade it a bit being my first pc build

[@aste6105]

I have a hp prodesk 490 g3 mt and it's perfect (i5 6500 cpu), the motherboard is powered with 24 pins connectors so I replaced the psu with 500W psu. I add 8go of ram and a rx 580 8gb for the graphics card and it's perfect! Costs : 80e + 20e + 20e + 100e = 240 euros ! 👌🏻 (sorry for my English, French people 😅)

[@johnnytaylor1243]

Merci beaucoup !!!

[@ArkonBlade]

Saw one of these with a 4th gen I5 and a family member doesnt have much money and i thought i could help him get a cheap gaming PC with one of these. well thanks for saving me money and time.

[@AmerdaMysteryOfficial]

When your video ended I felt abandoned. Sitting here with my new “gaming HP Prodesk” it runs really hot.

[@YuqieDest]

Do i really need a specific adapter for my prodesk 600 sff? I've already bought one, try it, beeping multiple times and just loops again...

[@rmgaminguk7079]

Upgrading prebuilds is a nightmare, particularly when sellers never post a picture of the insides so you can see the connectors. I though Hp didn't get this bad till later intel generations as I've seen HP Prodesks with both 4th and 6th intel CPUs and they used standard 24-pin connectors. The only adapter required is a adapter for the slimline DVD which needed a smaller sata power connector. The 6th gen cpu prodesk I got was the HP 400 G3 MT, I can't remember the exact model name of the 4th gen cpu version but it had an i5-4590S in it and I was able to upgradethe power supply and put an gtx 960 in it. Different sized PSU, wow, not thats a new level of prebuilt bullshit. Great video by the way, enjoyable to watch and informative. Thanks

[@coz0015]

I using dell sff atm use psu 700w outside n converter plus pcie extender for full size gpu

[@AlexSanchez-ku3lr]

lowkey not as hard as i thought i just got an rtx 2060 somehow fit it in an hp elitedesk with an i7 6700k and im ordering the adapter for the motherboard / power supply now wish me luck lol

[@AlexSanchez-ku3lr]

so power supply with adapter in, im running into one issue and that is its now giving me a power issue beep code, thinking its the adapter :/ could you link me the one you used possibly?

[@mohamedx4870]

Thank youu for adding Arabic captions. I really appreciate that bro

[@ZackEberly]

I don't know I did that. Your welcome my guy

[@jeffjularbal9404]

Will the 24 pin converter work on a Prodesk 400 G7 microtower? Ive been researchin for some time and I got to stumble upon this video. Appreciate this content.

[@coz0015]

I think I alr have pc n psu but still not change bc waiting gpu

[@dotheyfloat9961]

I've got a HP Prodesk 400 G2 MT and luckly it has a 24 pin connector for the PSU

[@ilikehotchiks]

So no adapter needed? Nice. I have a Prodesk 400 G1 MT my employer let me bring home. First time ever so go easy on me. Did you buy the PSU adapter to make it fit? Iam going to check my G1 now to see if it also has the 24 pin.

[@technomad900]

Just break out a soldering iron , solder on PCIE cables .. Job done

[@randomlyweirdjeff4638]

Just saw a video where a guy installed a new power supply that was larger than the original. It wasn't that hard. Just a lot of complaining. He put all new internals in the PC and had zero problem. Good video though.

[@brunderbergft4196]

Thank you for your informative video! So you have a subscription. I upgraded my HP Prodesk 600 G1 (power supply 350 watts max.) with a stronger i7-4790, 4*4GB DDR3 1600 Mhz Ram and a GTX 1650 GDDR6 4GB. The GPU has a TDP of 75 watts and the CPU has a TDP of 84 watts, so I didn't need any other power supply. The i7-4790 cost €40 and the GPU cost €85. The PC does what it is supposed to do. Examples of games: Forza Horizon 5 1080p, high settings (70-80 FPS); GTA5 1440p, mixed medium and high settings (40-50 FPS); DOOM Eternal 1080p, high settings (70-80 FPS). I am happy🎉

[@andrewosei328]

Just got the prodesk 400 G5 MT for a conversion to a gaming PC. I hope things go well

[@solmagnumxiii1734]

so how did it go?

[@andrewosei328]

@@solmagnumxiii1734 stock psu and an RX 560 4gb. Plays all the emulators I throw at it including Yuzu and Rpcs3. Specs : Intel i5 8500 8gb single stick XFX RX 560 4gb Seagate 500gb(the weakest link) I will get a cheap SSD down the line.

[@andrewosei328]

@Zahin 80+ bronze 180W. I got out the RX 560 and using just the intel iGPU now.

[@choxed.]

to avoid all that tomfoolery i just put in my old quadro 600 lmao, cant run the io shield because its too big but yeah it works. got about 400fps in minecraft java 1.8

[@RaaHall69]

Unfortunately I don't have a 3D printer to create an adapter for the PSU but the tape exists for something

[@ZackEberly]

I have them cheaply for sale, check description.

[@ronny3632]

i ran across your video and it saved me money by not buying this PC

[@ZackEberly]

Awesome!

[@EastAngliaUK]

Just picked up 10x HP ProDesk 405 G1 MT with an AMD 4500 but they have the normal plugs I think. they were free so won't say no

[@budahtsiki4723]

Thank you man 🔥🔥🔥❤️🔥🔥🔥, this video was helpful 💯, just subscribed 🔥

[@kundasemkundatam7461]

SFF is even harder. Bought EliteDesk 800 G4, put low-profile GTX 1650 inside (was lucky on GDDR6 one, had to buy low bracket from China…) and had to drill holes in cover so it cools down from 83°C immediately when jumping from game to task manager. Now waiting for 80cm long cables because the ones I got bundled with AX200 are too short and one had crippled that little MHF f*cker. AX200 and cables because normal card would be in front of GPU vent and way too close to PSU. My stupidity really shines with this purchase because buying used i5-8500, MB, some normal case and PSU would may be cheaper. But it is too late to abandon it at this stage because only thing which is left now is RAM. But hey, it can hit 100FPS in Warcraft 3 Reforged on highest settings! Which I limited to 75 to be the same as refresh rate of my monitor.

[@TheRealSandleford]

that 3D printer is pretty bad ass i mean just fabricate a part you want at home... yea gotta be careful of those adapters from china... inspect them well and make sure there arent crossed wires or anything like that

[@JesusAramil]

It's so weird finding out this video is we have the same monitor.

[@DaTateYT]

This should be renamed “why you should build your own pc”

[@aaronhacker3825]

I used a low profile 90 degree USB wire to smush a 760 in there

[@HelloTher1313]

It doesn't seem to have anything to do with efficiency to me, seems more like they just want to make it harder to upgrade so you have to buy a new computer instead.

[@ZackEberly]

Thats what I said

[@HelloTher1313]

@@ZackEberly not at first, but yes

[@__Alo__]

I wouldn't say that. These computers are business PCs, designed to be brought and used in bulk in offices. Less power over 100s of computers is going to show up on the electricity bill.

[@kenyyy999]

I have the same problem with the power supply but I don’t have a 3D printer what can I do?

[@ZackEberly]

I believe they sell some brackets you can buy. Maybe on eBay or something.

[@momineuropealikhan6949]

I have hp prodesk and it has 24 pin psu and is max 70w, and there is space for a big gpu

[@johncollins5552]

How much would you have to sell the 3d printed part for on ebay to make a profit roughly?

[@ZackEberly]

@@johncollins5552 check the eBay link

[@Thepigeons377]

i've got a used prodesk 600 G2 .. I7-6700 + GTX 1650 ( 75w) , cost just over £300 and for the money you cant complain really .The I7 was going for about £150 by itself at the time i bought the system back in may ,

[@mypfpiswhatourphonesees4294]

thats a really good pc to get by during these times when pc parts prices are through the roof.

[@aaqilhussaini8474]

hye i got this buld too but in i3 6100, Im also thinking of buying 1650, Can you tell me are you on the stock PSU? cause i cant find the converter of atx 24 pins for 600 g2 MT supported? Thanks

[@Thepigeons377]

@@aaqilhussaini8474 you can buy the standard 1650 , it does not need any extra power so no extra cables to worry about 😊

[@yasugi0153]

Do you have the tower version or the SFF??

[@CrescentZelda]

I'm doing this but turning it into a budget Mining Rig, if it weren't for your video about the PSU not being standard size I would've been so confused when I actually build it in a few days! Can't thank you enough for the PSU brackets!

[@ZackEberly]

I literally gave that PC to a friend for a mining rig.

[@sidleviticuzz]

Thanks for this video, I'm planning to get an HR Desktop Pro, but changed my mind LOL :)

[@nikonmarcelo1578]

I''m using hp prodesk 400 g7 small form factor pc and I dont know what gpu could fit there, but I'm thinking of buying riser cable, any suggestion?

[@alexandrebier4581]

came here 2 years later trying to find a solution for my g3 A that has a FOUR pin mobo connector. Not 24, not 6, but FOUR pin. I'm scared.

[@ZackEberly]

whatever you do don't die... be careful

[@zyllee6711]

Why would you buy a pre built pc when you will replace the main components anyways? The PSU was designed for power efficiency which is around 320W only. I currently have HP Compaq 8280 Elite MT PC with GTX 1050 2GB, 1TB SSD and 8GB RAM and it is still kicking for gaming despite the low electricity consumption.

[@ZackEberly]

Ok Zyllee, maybe some people want better FPS then 2 freaking frames. So like a normal person WE UPGRADE. It saves you more money by buying a prebuilt and upgrading it then instead of this retarded market where you can’t even buy graphics cards. That’s why Zyllee that’s why.

[@frostbitefilmsproductions6943]

For some mother board adapter will give fan error .

[@Schorlefritz]

This was pure comedy to me! I‘ve made the exact same experiences (Power supply, adapter, graphics card). I am running it with a GTX 970 in a small version (had to laugh so hard about the USB cable thing). My only problem is that when i start the PC, the power supply Fan triggers an error. I have to press F1 and it works. I can live with it but any suggestions? Anyways thanks for the laughs😂

[@CrispyBuda]

Is the cpu fan running at full speed?

[@trixtechtips1091]

Man you are awesome.

[@ZackEberly]

NO you’re awesome!!

[@ashleycarrington2186]

Great project - doing the same as u, was wondering what PSU use used for the bracket. Thanks Ash

[@franklinalfonso8098]

Instablaster...

[@philippepanayotov9632]

Sir, if you have this computer resetting in a never ending loop, what solution can you offer. Resetting the CMOS does not help and all components are being tested separately - they all work. So confusing. Any suggestion will help. Thank you. This was a great video. :)

[@Pond6]

I just bought a HP ProDesk 400 G3 MT off of ebay lol. Just wondering if you can link us to the video card you bought?, i cant find it for the life of me.

[@ZackEberly]

Well, they don't sell it anymore. The used market may have one. I'd look for something newer. Just make sure its short in length, and prolly on has one fan.

[@Pond6]

@@ZackEberly I see your probably right thanks.

[@manwithaplan4690]

its not that hard to turn these kind of PCs into gaming PCs, im running on an HP prodesk right now with a GTX 1650

[@ZackEberly]

Not hard at all, but annoying if you want more performance than a weak 1650

[@madcat4563]

So, which Prodesk did you have in the video? Because I'm looking at the 400 g3 (all looks standard), and it sounds like the 600 g(1&2) is also normal.

[@MichaelJamson-ex7er]

600g2 dont have the 24 pin

[@blackoutgaming8901]

I have created this abomination and have fit a 2070 super into it and a i7-4790k, evga 650w with a 24pin to 12 pin adapter into it, mainly trying to find a cpu cooler that would be up to snuff to keep my temps down

[@Keler477]

Do you have bottleneck?

[@blackoutgaming8901]

@@Keler477 None other then thermal throttling, Everything else runs fine

[@IBims1Mark]

@@blackoutgaming8901 Furry Protogen UwU

[@blackoutgaming8901]

@@IBims1Mark Uh, yeah?

[@IBims1Mark]

@@blackoutgaming8901 cute UwU

[@robhuff2336]

Thank you for this😅. Would you be willing to possibly post the file for that PSU bracket you 3-D printed?

[@ZackEberly]

Yeah I can, the holes need to be bigger as they didn’t quite line up. Let me see what I can do.

[@dodiwolverine9931]

@@ZackEberly waiting for you PSU bracket file... :-p

[@ZackEberly]

@@dodiwolverine9931 oh my, one moment plz

[@ZackEberly]

@@dodiwolverine9931 Check third link in the description

[@CrewElite]

Very Interesting! I really wan to build my own pc!

[@ZAKARIA-d8u]

When i start up my pc it make pip nois and in the bios pc tell me power supply fan not detected

[@Amritpalsingh-rd8dt]

Is GTX 1070 works in HP 280 g2 Mt? If yes how much gb?

[@eeamxx]

Sir, is there a solution for my HP Prodesk 400 G4 MT motherboard which only has 4 pins instead of 6 pins like yours?

[@eueu7046]

Hello, Great video. Every time i boot up my pc i always get an error: 90e Power supply fan not connected Any tips how to do that?

[@nicholasbrown8384]

Do you know if there is a 24-pin adapter for the Elitedesk 800 G6?

[@a88pockets]

You kinda sound like Matthew Broderick. Save Ferris

[@EastAngliaUK]

he does

[@Evgenyi82M]

Здравствуйте не подскажите? Hp prodesk 400 g6 mt.. Какую видео карту максимально можно или icore 5 можно туда?

[@williamedwards6519]

Great job, props on pur production value, too! Say someone did something crazy.. And Oh i dont know, purchased. An HP elite 800 mb To replace his gigabyte board sprting his 4th gen Core i5- i didcovered i need the adapter u found,buuuut whats with the front buttons? You mentioned them iquickly..

[@ZackEberly]

Sometimes with certain motherboards they have a sensors for the side panel or they need the right front panel connector to boot correctly. I’ve had this problem on a dell motherboard before.

[@williamedwards6519]

@@ZackEberly Maybe I overused my attempt at humor and subsequently fogged my situation. I zm familiar with the sensors for side panels, and all in pack connectors vs two pin modular similar to jumpers type connection for front of PC functionality ( pwr, reset, turbo, hdd LED, etc) I am asking, is: Does the HP board in your video have proprietary front of PC connectors ?

[@kyner7734]

I put gtx 1050ti but the system don't detect it, instead it detect intel hd 530 Edit: I install new nvidia drivers and its works

[@ZackEberly]

Lets GO!!

[@Stefan_xd]

I have I5 4570 paired with 1050 Ti and it's OK for most games at 1080p gaming but I would like to upgrade it to maybe possibly 1440p gaming, is it possible?

[@ZackEberly]

@@Stefan_xd Your cpu will start bottlenecking a more powerful gpu. That being said, a more powerful gpu would get you closer to 1440p gaming.

[@Stefan_xd]

@@ZackEberly what I meant is I want to upgrade both CPU and GPU but I don't know if the 1440p gaming is possible with this case because of the 320W power supply and the size of the said case

[@ZackEberly]

@@Stefan_xd yeah, you’d most likely need a higher power supply. 650+ wattage

[@coz0015]

so normal/standard psu isn't fit the case need put outside lol

[@ZackEberly]

No, it'll fit. It just cant be screwed in properly, so it'll raddle and fall out of place. Try watching the vid, literally was the complete opposite what you thought happened.

[@coz0015]

@@ZackEberly already watch n alr buy n have the new psu I just waiting the gpu half size gpu n no power pin is a must right? since it have usb3 front panel cable

[@Sensei-uu1eq]

Oh My God! De dónde sacaste esa panelota brother?

[@VIAJERODELTIEMPOMX]

De Italia, jaja, él no habla español, hermano. Jaaja

[@zombiezebra14]

Omg thank you!

[@pixel-mods3662]

Why did u change the whole power supply??

[@ZackEberly]

So i could power a GPU with pcie connectors.

[@pixel-mods3662]

@@ZackEberly i have a prodesk 600 g1 twr I wanna buy a PNY GTX 1660 Super Single Fan, and i wanna know if it's going to fit And if i can use it without problems of power supply and stuff

[@LordDahaka33]

What prodesk model is this prodesk 600 g1 or g2?. Thanks

[@Creepsquad1179]

It says in the title and picture G1!

[@Rev2much]

360p?

[@ZackEberly]

I guess you were to earlier, KZbin’s HD encoding servers are a little slow sometimes.

[@TonicofSonic]

Does this apply to the hp prodesk 400g3 tower?

[@coz0015]

this mt version i think

[@blatantstriker]

We'll damn u got a new viewer

[@anasbouteldja3047]

I bought an hp prodesk 400 g2 mt and the psu is only 180w, I’ve seen that the motherboard have a 24pin connector is it good for me to change the psu?

[@ZackEberly]

Yeah, as long as the connectors like CPU and motherboard connectors are standard you can switch it.

[@onocentaur8360]

How conect pci-e power for the graphics card?

[@jaredbourque4199]

Is the motherboard a mini atx, could the motherboard be swaped?

[@ZackEberly]

It’s a micro atx motherboard, so yeah it can be swapped for something else.

[@jaredbourque4199]

@@ZackEberly hey, thanks for the reply 😀👍

[@RespekfulFungus]

It’s really not that hard. Just be okay with an rx6600 or a gtx 1660.

[@ZackEberly]

Okay

[@chrispurle5977]

Love the video! Watching in the UK. I just bought 4 of these prodesk machines and looking to do the exact same as you (x4) to create entry- / mid-level gaming rigs. I'm loving the psu bracket and really hoping you can send four over the water to England? Hoping you can help me out. :) Ive sent you a message on ebay. Thanks Zack

[@ZackEberly]

I saw your message on eBay, currently looking for shipping rates, I'll see what rate i can get and it'll be through PayPal.

[@chrispurle5977]

@@ZackEberly thanks man 👍

[@ZackEberly]

@@chrispurle5977 I sent you a message on eBay about the totals. Go through PayPal invoice to avoid eBay fees.

[@ZackEberly]

@@chrispurle5977 I got your payment and shipping it today.

[@chrispurle5977]

Zach... what can I do to get a standard graphics card in there?

[@WabbiTSh4rK]

Hey great video, do you know the dimensions of the RX 480 by any chance ? Can't find them on the net.

[@ZackEberly]

The Cards PCB is 7 inches long and the shroud/cooler is an 1.5 inches

[@_marreu_]

what adaptor cable do i need, if i want to keep the power supply (i dont want to keep it, im just broke)

[@ZackEberly]

You want to keep the HP power supply but want a graphics card in the PC?

[@_marreu_]

@@ZackEberly yes

[@ZackEberly]

@@_marreu_ well it depends, what card are you planning to use?

[@_marreu_]

@@ZackEberly rx 570 8gb , the problem is that i am dumb and i already have it and somehow it fit in the motherboard l, now i just strugle with the power cable and psu

[@coz0015]

@@_marreu_ use pcie extender $6 the white one

[@CreativeCommons277]

Bro can I by any chance pair GTX 1050ti

[@ZackEberly]

IDK, will it fit then yes.

[@johndustin158]

i have a dell an it has a 24 pin connector

[@ZackEberly]

Congrats my guy, consider yourself blessed!

[@Kajukota]

My hp prodesk does too. Guess because i got an older generation one

[@carlono1]

@zack Do you think i can use the 180 w power supply to run a gt1030 in the setup? Or do I need more power?

[@ZackEberly]

I believe the max wattage from the PCIe slot is 70 watts or so. If the rest of your PC is extremely efficient then maybe but I tried running a GTX 750 in a dell pc with 280 watt PSU and it didn't work, so I'd recommend getting a larger PSU.

[@TexasRoadSavage563]

I’m bout to try this tonight

[@JZQuartz]

Can i get it to work with low profile gpu that doesn't have 8pin with the adapter and is the pc going to last long?

[@ZackEberly]

That should work. Make sure the GPU is to long but you should be fine with a low profile card.

[@JZQuartz]

@@ZackEberly alright thank you!

[@JZQuartz]

@@ZackEberly one more thing how long can the adapter last?

[@assassin1148]

I’m about to buy a hp 600 g2 has anyone had one of so was it any good

[@lennylicious69420]

Well you’re better off with a dell optiplex as it’s a lot easier to upgrade. When I got dual channel Corsair vengeance lpx into mine, it started spitting error codes at me so I had to go with white DIMM slots instead of black. Hp also made sure to design the motherboard so the front USB ports’ connections to the motherboard were right in front of the pci slot so you can’t boot the pc with a full size gpu without getting a warning in the bios saying’ no fan or usb detected’. (Idk why it says fan) but you can ignore it by pressing f1 . I’ve gathered all this info from cobuman and a few other KZbinrs . Hope this helps And I probably wrote too much

[@assassin1148]

@@lennylicious69420 no I appreciate it a lot bro, I just wish I knew it before I got it, idk if it’s mine or if everyone has problems trying to run games but mine won’t run fortnite or anything with graphics like that I play tibia it’s a 2d game that came out in 97 and it lags on it sometimes lol idk what to do

[@lennylicious69420]

@@assassin1148 glad I helped you bro. I’ve upgraded mine so my next step is a case swap as I can’t find a low profile gpu because of the shortage. Oh boy I can’t wait to switch motherboards

[@mypfpiswhatourphonesees4294]

@@lennylicious69420 im exactly in your position rn, but i already did a case swap but i plan to keep using this cpu and mobo until i can afford a more powerful Cpu and mobo. Mine is running i5 4590 with rx 570 4gb and 12gb ram, it runs the games i wanna play pretty well so im not really in a hurry to upgrade my cpu.

[@Supermanzs]

I think I will stick with my gtx 1650

[@PNHassett]

I have a hp 8200, I feel ya. 'm trying to figure out how to put in after market cpu fan heatsinks into a hp prodesk 600/800 or a 8000 series hp. I've noted the HP 711578-001 Heatsink has brackets you screw on to the heatsink. It's the brackets that might be usable with after market cpu coolers such as the ID-COOLING SE-224-XT , if I drill some holes in the Hp brackets. Proprietary Hp cpu heatsink holes are a bitch.

[@PNHassett]

The propriety Hp holes on the heatsink are 4 inches by 3 inches. I could get ANBE AMD Plastic CPU Fan Stand Bracket which are 4.33 in by 3.15 in......I'm more interested in the 3.15 inch portion of the bracket which has a clip on mount. Since it's plastic, that would indicate it's easier to modify and use it with a Antec CPU Cooler that has snap on buckles, which is the reason for the 3.15 inch clip on mounts........this is all theory, and relatively inexpensive but effective. So, I'll buy some and reply.

[@PNHassett]

Bought the parts, don't match. Returned part. Looks AMD like 3d parts have to printed to HP specs. Clip on cooler seems to be most feasible.

[@auraaura1918]

Yo can I put a 10 inch gpu in it? And can I just zip tie the psu?

[@ZackEberly]

If you wanted to fit a 10 inch GP you would have to remove the extra hard drive cages so no and as for the psu you could zip tie it in that’ll work.

[@auraaura1918]

@@ZackEberly ok

[@auraaura1918]

@@ZackEberly for me it fits but I need the angled adapter

[@senpaikaso6523]

Bro im having difficulty on Installing back my windows from lubuntu im tryin to Do the f12 thingy with bootble windows on my usb but still not showing anything its all black then it will re start on lubuntu like its forcing out windows installation

[@ZackEberly]

Well, did you try reset the bios/uefi?

[@senpaikaso6523]

@@ZackEberly how broh ??

[@ZackEberly]

Did you watch my video on it?? Or just skip it and go to my latest video to comment so I’d see it.

[@senpaikaso6523]

I'd skip just so you notice me

[@ZackEberly]

How about you watch the vid and then comment on that video, so others can see. I’m quite active on my channel so I don’t think I’ll miss it.

[@bgbggg1827]

best cpu for this computer?

[@mypfpiswhatourphonesees4294]

i7 4790

[@JohnSmith-bh8um]

Bought one of these atx 24 Pin to hp adapter. It did not work. If anyone has a link to one that does work let me know.

[@ZackEberly]

There are 2 different kinds. I got lucky and pick the right on up. -www.moddiy.com/categories/Cables/Branded-PC-and-Server-Cables/Dell-Cables/ Try matching the exact model number to the appropriate adapter.

[@JohnSmith-bh8um]

@@ZackEberly your awesome. I'm ordering one right now. Upon further inspection, the one I ordered was for an hp z220. The one I needed was for a pro 600.

[@godfreyoupa8571]

Can the gtx 960 full size fit

[@ZackEberly]

Might run into issue with spacing with the motherboard and not the case.

[@blade8424]

Just want one for basic gaming. Anyone know if i can fit my GTX 1660 Super for VR Chat and Oculus? Much would be appreciated! Found one on ebay for $250. :) Its an i7 6700. :) Can probably play Fallout 4, Skyrim Special Edition and Skyrim VR with mods in it. :) id get another Z240 but those are hard fo find now. :( plz respond lol. I need a PC and going nuts with out one. 😂

[@wsideRJ]

I need help finding the bracket

[@ZackEberly]

I sell them, check the description. If interested

[@wsideRJ]

Oh I missed it then I think they are out

[@ZackEberly]

@@wsideRJ Sorry about that, the links are now updated.

[@deadaiir]

Please do not use shoddy adapters to power your PC.

[@ZackEberly]

There's actually nothing really shoddy about it. Match current and do your research and it looks like someone already did the hard work and now offers a product. Yes I understand your concern but I've been using it ever since and it works fine cuz its so simple.

[@vonronaldrio5226]

come on bruhh what do you expect.. if u have problem with 24 pins, yo u can buy adaptors..tsk tsk then buy a new case.. is it a problem???

[@ZackEberly]

tsk tsk… bruhh what do you expect.. me to be made of money? If you have money send to me plz

[@porojorojo4278]

Checking the benchmark channel... Doesn't exist (Edit KZbin channels are case sensitive)

[@ZackEberly]

if you search for "mczack" on youtube, my cannel pops up first even on an incognito tab -kzbin.info/www/bejne/b4XEhYaOls2Ii5Y

[@macanshot]

I have one, with a 2gb card and 16gb ram

[@centtimmy4951]

Would an a2000 fit

[@ZackEberly]

Yes.

[@Cigrzz]

What the power supply?

[@ZackEberly]

Old one or the new one?

[@Cigrzz]

@@ZackEberly new one

[@ZackEberly]

@@Cigrzz I think it switched in the end to a 500 watt Thermaltake PSU.

[@robloxiayeah3082]

Its already gaming

[@Deludedposting]

Or just buy a HP prodesktop 400 G1 IT HAS NO PROPRIETARY CONNECTORS

[@ZackEberly]

Sounds like a great idea, to bad you DIDN'T tell me this several months ago... but on the bright side, I made some money so its a win for me.

[@Russell970]

You've the cutest face IMO, Geeky cute.