HPI Maverick Strada EVO MT Part 12: 4S Baby!
Рет қаралды 835
Күн бұрынJust for fun I'm installing a larger brushless motor and bigger ESC! This truck can now run 4S LiPo batteries.
Watch a review of this upgrade in my video after lots of testing: • HPI Maverick Strada EV...
This upgrades makes wheelies never ending as there is now so much power and torque. Hopefully the internals can take the extra power!
Strip down starts at: 3:07
A break for some chat at: 4:13
Bigger motor and ESC install starts: 4:40
Install finished with bench test: 07:12
Taking her for spin: (reminds me of power boat racing 😂) 09:15
Watch my other Maverick Strada MT videos:
Part 1: Introduction: • HPI Maverick Strada EV...
Part 2: Installing Belly Plate: • HPI Maverick Strada MT...
Part 3: Brushless Upgrade • HPI Maverick Strada EV...
Part 4: Brushless Test Drive: • HPI Maverick Strada EV...
Part 5: Wheel and Rim upgrade • HPI Maverick Strada MT...
Part 6: Servo Upgrade: • HPI Maverick Strada EV...
Part 7: £5 Wheelie Bar: • HPI Maverick Strada EV...
Part 8: Alloy Hub and Hub Carrier Upgrade: • HPI Maverick Strada EV...
Part 9: 3s LiPo Top Speed: • HPI Maverick Strada EV...
Part 10: Hub Hex Extensions: • HPI Maverick Strada EV...
Part 11: Bashing: • HPI Maverick Strada EV...
Review of Upgrades: • HPI Maverick Strada EV...
@corecasrcworld7100 5 жыл бұрын
Mate looks and sounds great ! Just recently installed a new motor in my jumpshot and that too wheelies for fun. Enjoyed the vid and keep up the good work 😉👍🏽
@tiborvon 5 жыл бұрын
Beast!!!!
@tiborvon 5 жыл бұрын
#55 i have returned the sub dude and thank you 😆
@philthyco1 5 жыл бұрын
Built yourself a true monster..It will hold but a slipper might help
@budgetrccars9385 5 жыл бұрын
Haha it's a bit silly now but puts a smile on my face 😁 A slipper clutch would be a good idea actually 👍
@ahmetefebektas496 5 жыл бұрын
I have the same rc and i love it but i have the same problems with the wheels
@budgetrccars9385 5 жыл бұрын
Try using Loctite. Mine don't come off if I use this.
@ahmetefebektas496 5 жыл бұрын
@@budgetrccars9385 That sounds clever man. I will try this. Thx!
@budgetrccars9385 5 жыл бұрын
When your wheel nuts are new they, usually, have a thin layer of plastic inside the nuts. Once you have taken the nuts off and on a number of times this weakens and sometimes removes the plastic. Loctite basically replaces it but you will need to use every time and you have to wait 24 hours for it to set before using the car/truck. You apply it to the drive shaft and then place and tighten the wheel nuts. I hope this solves your problem 👍👍👍 😊
@budgetrccars9385 5 жыл бұрын
Trust youtube to have a video about it 😂🤣😂🤣😂 kzbin.info/www/bejne/bKHRZHZrhruWq5I
@gonzodetroitify 5 жыл бұрын
So I've watched this video and do not even have this truck, but when u 1st gave power to the new set up @7:30 how comes the wheels were not all moving as 1, yet this is 4wd🤔no?? Some span whilst maybe another was not, or when u were off trigger maybe watching the video was top left was not spinning and the bottom left wheel I think wasn't movin same time others were??
@budgetrccars9385 5 жыл бұрын
The truck has an open differential so only the wheel with least friction spins. In most situations only 1 wheel at the front and 1 wheel at the back will spin. If all 4 wheels have the same amount of friction then they will all spin. The reason why on the bench test only some wheels span is because I had some wheel nuts tightened too tight. Normally on a bench test all 4 wheels spin together.
@Madmancandfamily 5 жыл бұрын
Sweet she looks awesome... 😂 I'm constantly chasing wheels too
@jordanfox.7434 4 жыл бұрын
What is the motor shaft size and did you use the stock pinion
@budgetrccars9385 4 жыл бұрын
The shaft size on the motor is 5mm and the stock pinion is 3.125mm
@jordanfox.7434 4 жыл бұрын
@@budgetrccars9385 thanks
@nextworldflair 4 жыл бұрын
@@budgetrccars9385 how did you drill the pinion to 5mm??
@budgetrccars9385 4 жыл бұрын
@@nextworldflair I didn't. I bought a new pinion. 👍
@creative_expressionproductions 3 жыл бұрын
Did it survive
@budgetrccars9385 3 жыл бұрын
It did survive but I have moved onto other cars now. It was a great truck and amazed the stock parts held upto the 4s abuse. 4s is too overpowered though and the truck is really suited to 3s but the power wheelies on 4s were great fun.
@ВалерийЯкушин-ъ3й Жыл бұрын
Круто!