Subscribe & Like for more Business Inquiry: Khalsrt.business@gmail.com Follow me on Instagram @Khal_SRT khalsrt.com/
Пікірлер: 156
@KhalSRT8 ай бұрын
BACK ONNNN
@markus360s8 ай бұрын
Yessir!🔥
@hueymaker43448 ай бұрын
Nice. That work paid off. Man, I got fired from McDonald's and uber eats and can't get a job anywhere. Can anyone help?
@jameswillis22388 ай бұрын
Yooooo how do I contact you for a swap fam @khalSRT
@jameswillis22388 ай бұрын
I got a Chrysler mad ready for the redeye swap
@Smiles5.78 ай бұрын
I need my chrysler 300s swapped , I got a donor car already. How do we discuss business ?
@thecarlotmechanic45318 ай бұрын
This happens to a lot of high-performance vehicles from novice drivers. doing launches right after start up…..so if he just started the vehicle and launched it . the lifter compressed, but it did not have the oil pressure/proper amt of oil in lifter to spring back up and it bent the push rod simple as that. there is no misfire now ! So the lifter did not spin and CAM did not get chewed up, simply a bent pushrod. Lucky is the owner of this ride 🙏 blessings to you and your channel Bro.
@MrAnxious8 ай бұрын
What caused it do bend though?
@VTEC-YO8 ай бұрын
probably starved of oil
@eatshiy8 ай бұрын
Bought a 2015 300s few years back, redline pearlcoat paint and i did full tint...I have been getting compliments almost EVERYDAY for the past 5 years....love my 300!
@Graphixdini8 ай бұрын
I wanna see the hellaphant in a Durango I think you the only one who can pull it off
@911lineman9118 ай бұрын
First.. your channel is 💯 on point! Between content, editing & flow your straight killing it. As for that engine I’d be more concerned with the abnormal wear stressed on lifter, spring and cam lobe. So it’s either replace and roll with it and see if it last or strip down to mic cam and send head to machine shop. It’s a tough call, hopefully it didn’t run to long with that wishbone and all is well. Great channel 🤜
@gnd1114 ай бұрын
Always get engine to operating temp or 160 minimum before you have fun. Well known by mechanics for 40 years
@josephcentola89918 ай бұрын
Much love and support from Boston 🙏🏻 ❤
@NoNegotiations8 ай бұрын
Next video, "Its back, owner wants new engine" 🤣🤣🤣
@davidpeterson61478 ай бұрын
it is not fixed IMO. Typically, a pushrod will not bend like this unless the lifter fails and gets stuck in the bore. You should do an oil change and check the oil filter media for metal chunks. This is the easiest way to check the engine for damage. You could also send some of the oil off in a sample and have it evaluated.
@KhalSRT8 ай бұрын
Customer stated that he didn’t wait for temps to get to operating level before getting on the throttle soon after he did it started to make that noise.
@Cstmade8 ай бұрын
Wouldn’t that add to the chances of the lifter getting stuck? Oil didn’t properly lube the engine by the time the driver mashed the gas.
@cbruno121808 ай бұрын
I don’t think it’s fixed either there is a reason why that pushrod bent to begin with I think there is an issue with that banks valve train assembly and I’m gonna ask my buddy who is a 30 year master tech at dodge here New York upstate Albany area I’ll get back to u
@deschampsjeff8 ай бұрын
@@KhalSRTdang, so sad some people have money to buy that stuff but they don’t take care of it. My hemi warms up at least to 100F until I put it in gear, still I don’t press the throttle until it reaches at least 180F
@fast_427_ss88 ай бұрын
I was thinking the same thing
@mohamedalyassari-vp9pl6 ай бұрын
M5 VS hellephant rolling
@Kwalafied428 ай бұрын
Never ever is the pushrod the problem it is just the failure point.
@jaydee32658 ай бұрын
Perfect job! Thanks for the Vlog.
@KhalSRT8 ай бұрын
thanks for watching!
@tamarcokitchens28358 ай бұрын
That shit look like it aggravating
@davidconley36108 ай бұрын
I’d say the motor was over reved and bent the push rod !!
@KhalSRT8 ай бұрын
I agree
@XyXInc8 ай бұрын
not entirely fixed, likely more damage there. You just fixed the easiest piece tbh. I'd check the oil and likely put a camera in the there to check the walls of that piston.
@Mattschuster916 ай бұрын
This the dream build for me right here. Just grabbed a 2023 300 AWD bc of the weather and I love the car but once I have the money the goal is what you got! Love seeing this build man keep it up.
@Richking2135 ай бұрын
He’s actually building his first AWD 300 at the moment 🔥
@De.aurious8 ай бұрын
man escalade so damn clean
@user-ru1hy5kz5u7 ай бұрын
What year Chrysler 300 is it
@ripjanetstrimel33128 ай бұрын
This car sounds nasty man I love this car
@csmlth728 ай бұрын
Something caused that pushrod to bend like that....prediction ....it will do it again...
@shonnwashington10098 ай бұрын
Aren't those hydraulic lifters?
@StuffandThings18 ай бұрын
at 7:27 why does the bent rod appear to be the same length as the new non-bent rod?
@Almightycreator8888 ай бұрын
I thought you sold that Daytona?, thats sitting outside
@VimyScout8 ай бұрын
That looks like some strong resistance to be able to bend a push rod like that.
@slinkhardtimes28528 ай бұрын
Man i wish that he still had that car good Contact
@janelevitt1066 ай бұрын
How how did you get that?
@nedunonnyp7048 ай бұрын
Taking off that valve cover is 1/2 Of the job. Especially those center bolts. Next time I do this im taking the whole engine out! Lol then Fighting to wiggle it out is another Fight.
@yousifsabe85718 ай бұрын
DAMN NICE CAR!!
@scubaray328 ай бұрын
Man you are the best 👌! I have to say that Cadillac Escalade-V looks good keep up the good work and God will continue 🙌🏾 to bless you my brother
@derrellewashington27978 ай бұрын
Best to ever do it
@grundyb8 ай бұрын
I like to coat the battery terminals with dielectric grease. I coat each terminal completely and I never get that corrosion stuff all over.
@JorgeVega-re7cm8 ай бұрын
And that's how it's Done my Guy you are the man. Love all of your contents.👍🇵🇷
@JorgeVega-re7cm8 ай бұрын
I Love the work and Dedication you put on Building these car.
@houseboatrob42388 ай бұрын
I get the feeling that your gonna have trouble with that same problem.
@Boogersgrow8 ай бұрын
Yous a Mopar genius 😊❤
@godsentdrew90477 ай бұрын
How much do you charge for an engine swap?
@michelblutz55288 ай бұрын
What caused the bending? Grtz from Spain.
@srturoo8 ай бұрын
When are you dropping for us to use you as a broker I got my eye on one car on iaai
@JamesBrown-gf6sc8 ай бұрын
Pull the motor, tear it down, there's further issues hidden that will cause this engine to go again
@flatbedjay76728 ай бұрын
You can't just replace a rod without finding the cause of it getting bent bro😢.
@3602go8 ай бұрын
Rod???
@jeromejozwiak47058 ай бұрын
Rod, you do mean push rod . When a push rod bends like that one, did 90 percent of the time they bend like this one did because of the engine being over reved. So there isn't anything else to be fixed other than the driver to stop over reving the engine .
@flatbedjay76728 ай бұрын
@@jeromejozwiak4705 false ask buddy why he keep deleting everyone's comments? Truth hurts
@03mm248 ай бұрын
@@flatbedjay7672well flatbedjay you going tell us why the pushrod can be bent other than over revving....you call somebody comment false but you don't explain on your own
@lifeofmike51268 ай бұрын
@@flatbedjay7672 dude was revving the shit out that motor laying on the rev limiter that's exactly how u bend push rods
@392scatpack38 ай бұрын
I still will run a compression check on that cylinder what I push rock came from. Something bent it. When I had my race car Had a push rod do that come to find out the lifter. Had a hole in it.
@blaquesrt8 ай бұрын
Like a few other's said, its a reason why it bent. now I'm thinking is lifter or cam lobe bad on that cylinder. Was oil level low? Did oil need to be changed? These cars run at high temperatures, thats why fans continually runs. I would definitely look into it further. It will probably happen again.
@KhalSRT8 ай бұрын
Im thinking it was over revved at cold temps. If the cam was damaged and chewed up the lifter there would be a noticeable mis fire.
@abrahamlincolneats31838 ай бұрын
What's up with the Cadillac v truck drop a video on it
@terrancehill87328 ай бұрын
Bro tht simple ass part thts why mechanics charge mf’s so much lol
@hellcatredeye-g65828 ай бұрын
Unfortunately where they locate the battery to the rear of the vehicle doesn’t keep the battery warm like it would under the hood and the batteries are junk. The dealer wants $450 for one but I got an AGM battery now from o’reillys under my account, and I have had no problems. Got several customers that had the same problem with the dealership batteries👍
@nickissa8 ай бұрын
Khal don't sleep.
@SixTwoHemi8 ай бұрын
Jon moored from moored performance is based in Michigan. He will have that car flying
@StupidStuffSmack8 ай бұрын
let's hope this masterpiece stays in good condition this time
@Ls3adrian8 ай бұрын
I would have put some BTR ones that are stronger material
@deschampsjeff8 ай бұрын
The dash says 340KM/H, that’s amazing. I wish I could get one of those.
@racinjasonrt8 ай бұрын
Saw you earlier at the gas station lol, 300 is killer man 🔥🔥
@KhalSRT8 ай бұрын
thanks man!
@MrBloodguns8 ай бұрын
You don’t have to torque them down?
@mrmilo52038 ай бұрын
LETS GOOOOOOOO!!!!!!
@evoLChow8 ай бұрын
Bro how can I order the hellaphant supercharger? I want the 3.0 instead of 2.7
@THISguyM1078 ай бұрын
It’s gonna get bent again. Need to find the root issue. Also that engine needs to have hardened pushrods for the abuse it’s probably taking.
@user-yx7qd3xs8b8 ай бұрын
What mopar are you going to do next
@CaliAl678 ай бұрын
Good job my brother the best content ever 👏 👌
@markus360s8 ай бұрын
🔥🔥🔥
@fredoniecee21448 ай бұрын
Let’s get it🦍💯
@Nfs-HP-Enjoyer8 ай бұрын
Stop racism 🐵🤜🏿🤛🏻🧑🏻
@dunnrite82998 ай бұрын
What caused it to bend that push rod 🤔👀
@kendricktaylor61578 ай бұрын
Can you put insurance on the Motor since it’s only 1000 made. If something happens to it u are covered. Hate to see stolen or unrepairable
@_noname6178 ай бұрын
Why not replace them all?
@MM_in_Havasu8 ай бұрын
Simple fix, glad it was only $6 to repair the engine! Good news all around! Thanks Khal for the video update, got lucky on this one!
@KhalSRT8 ай бұрын
Thanks for watching!
@reggie_m458 ай бұрын
We still sint get a video on that escalade
@mikegreen30478 ай бұрын
I would be more worried on why did the push rod bent and I didn't know that the dealership will sell just one pushrod lol
@KhalSRT8 ай бұрын
Yup you can buy just one if needed, i assume it was full sent on cold temps. I've seen this happen before.
@lifeofmike51268 ай бұрын
@@KhalSRTthat's exactly wat did it bro oil was thick clearance was still tight revs got higher then boom
@srthatejeep8 ай бұрын
you didnt want to clean out that air filter 🤨
@kayla-hv1bm8 ай бұрын
a lifter had to fail for the pushrod to bend like that
@StreetyCoD8 ай бұрын
can't believe he sold this lol but like he said tho for the right price anything is for sell.
@Acethacutt8 ай бұрын
🎉🎉
@haydenjelinek30947 ай бұрын
I have an AWD 300 and I want to swap it with a 392 and have it RWD. Can I take the drivetrain off of the donor car and put it on the 300?
@Bank2268 ай бұрын
🔥👌🏾
@thelronrichards83568 ай бұрын
Aye bro how can I get a car done
@gd19968 ай бұрын
Should have upgraded them all... stock pushrods are weak. Then again it wouldn't just fail for no reason.
@user-zr8hu8pn1y8 ай бұрын
What part of Michigan you on I wanna see your car 😍😍😍
@tiahodo118 ай бұрын
Detroit
@lifeofmike51268 ай бұрын
All these comment mechanics i bet 85 percent couldn't build there way out of a brown paper bag😂😂
@93baby8 ай бұрын
Yes sir
@3900TheLabel8 ай бұрын
That shit ain’t fixed man lmaoooooo
@SaltyGringo17768 ай бұрын
👍
@Kylescars_15 ай бұрын
How mush
@lennonnaylor40248 ай бұрын
hey khal i live in australia how much would it cost for me for u to build/swap a 300 cat w right hand drive
@UnknownUnknown-oh2tw8 ай бұрын
Starting at 40,000!!!
@UnknownUnknown-oh2tw8 ай бұрын
-his words btw
@lennonnaylor40248 ай бұрын
@@UnknownUnknown-oh2tw how do i contact hiim
@chrisfairnot65228 ай бұрын
🍿😊
@hueymaker43448 ай бұрын
Nice. Man, I got fired from McDonald's and uber eats and can't get a job anywhere. Can anyone help?
@EldePHX8 ай бұрын
If you got fired from those places. Then you are clearly not a hard worker lol
@FreeBandsTy8 ай бұрын
@@EldePHXlol we know that tho he asking us for help 😂
@hueymaker43448 ай бұрын
They fired me to save money.
@plugzunited30878 ай бұрын
Find Your Nearest Temp Agency My Boy
@NotMyFoodStamps8 ай бұрын
I was the 1,000th like. Just wanted to share that with everyone lol.
@chevyboi_srtv8 ай бұрын
I need a swap bro hit me up plz
@jonnyboi53518 ай бұрын
That’s not no fix a real mechanic would say the same thing that car is going to be back just watch oh not to mention cam is most likely damaged
@lifeofmike51268 ай бұрын
I don't think he ever claimed to be a mechanic bro he just fixes and flips he's helping the guy out more than anything
@jonnyboi53518 ай бұрын
@@lifeofmike5126 that’s not a fix tho that would just get the same results again the engine wasn’t built right if it got a bent rod I work on cars everyday at the shop I own I’ve seen this several times before same results after a few months
@SixTwoHemi8 ай бұрын
Bent pushrods also come from over revving….Hitting the limiter way too much.
@Jhrivera6218 ай бұрын
The owner lucked out. Mine has the same ticking noise and it’s definitely not a push rod. It’s a busted lifter. Now I have to replace the cam, lifters and all. Good times. Awesome content as always brother 💪
@cliffhanger_5.7348 ай бұрын
Good reason to put in a larger cam?😁
@Jhrivera6218 ай бұрын
@@cliffhanger_5.734 Absolutely! Going with a Comp Cams stage 2 HRT master cam kit
@mikegreen30478 ай бұрын
sorry to hear that but these hemi engine are easy to work on, its just time consuming. i just put a cam in mine last week. make sure you change everything while your in there and i will say this... the hardest part for me was taking out the oil pump... my god that sucked so bad, took me 1-2hrs just on the oil pump bolt on the pick up tube. its hard to get to because of the oil pan is in the way. i would of left the oil pump in if i knew it was going to be that hard or just say fuck it and drop the oil pan. i have the 6.4L hemi so not sure how its like on the 6.2 or 5.7 or 6.1
@Jhrivera6218 ай бұрын
@@mikegreen3047 Agreed. Everything is getting changed out. Lifters, cam, push rods, timing chain, oil pump and all needed gaskets. Replacing the oil pump is easier by removing the oil pan. Extra steps but necessary to get the job done. Crazy excited for the outcome
@mikegreen30478 ай бұрын
@@Jhrivera621I should have dropped the oil pan but i was being lazy and didn't want to break the seal lol and parts are not easy to find nowadays...lots of parts are on back order. I swear covid mess everything up in this world bad. I'm not sure if you have a 6.4l hemi but if you do make sure you get rid of that eco mood bs! that makes it drop down to 4 cylinders instead of 8. the dumbest thing Mopar did was that eco shit. they should have made it to where you could at least shut it off if you wanted to
@michaelbuchanan-fu2tg8 ай бұрын
True mechanic never wear gloves
@miguelduran3518 ай бұрын
Change those rims on the Escalade pls
@hawkhim00238 ай бұрын
🔥🔥🫡
@ewillson49538 ай бұрын
KHAL , I WILL BE 69 IN NOV. I WOULD LIKE TO HAVE ONE OF YOUR CAR/TRUCK.I CAN COME PICK UP WITH CASH. PLEASE LET ME KNOW IF YOU THINK IT CAN HAPPEN..THANK YOU SIR
@user-tx9hr8zd9f8 ай бұрын
Good old crapsler !!! Any company that would use the word scat ( playing with POOP ) in their production cars says it all !!!! J U N K , getto horsepower !!!!!