Ice maker or water dispenser not working - Refrigerator repair - Kenmore Whirlpool

Replacement Bracket: amzn.to/2eutO4Q
If your dispenser makes ice but will not drop any, or if you can not get water, watch this video. If you don't hear a "click" noise when you push in your ice dispenser handle or the water dispenser handle, you likely have a broken switch or a broken switch mount. In this video, I show you how to open the dispenser and fix the mount. You can also replace the switch if needed. The fridge I am working on is a Kenmore but you will find that many other brands are built the same.
SUBSCRIBE→ www.youtube.co...
•••••••••••••••••••••••••••••••••••
For those who offer to buy me a drink, thank you! I have Venmo and CashApp.
Venmo: AdamCash
CashApp: $AdamDIY
•••••••••••••••••••••••••••••••••••
Business Inquiries: please email:
/ adamdiy

[@deannac9623]

Thank you so much for this detailed video. I just fixed my 13-year-old Whirlpool side by side refrigerator. The ice in the door was still working but the water stopped about 2 weeks ago. I had about decided to replace it rather than spend money on what could be the first of many repairs, considering its age. I had already fixed a problem with the drain in the freezer that was clogged using a KZbin video so decided to see if I could figure this one out as well. It took me about 45 minutes to complete but a lot of that was because my tools are out in my workshop in the barn, and I had to make two trips. (I know better than to just bring one drill bit.) Plus, I have arthritis in my right hand and that makes things a little slower as well. So, thank you again for saving me either the cost of a new fridge or a service call/repair. Gratefully, this 69-year-old handy woman.

[@ego7767]

Adam you are my NEW BEST FRIEND. My water dispenser stopped working...And as you've showed..the bits had broken inside. I did exactly what you showed step by step. I drilled and anchored with long screws ...HALLELUJAH the water dispenser worked!!! Not bad for a 61 year old girl :) Thank you for your kindness in helping people like myself that would go into bankruptcy hiring "fixit men" to fix what I can with your help. Your Mama should be proud!! Many many thanks!!

[@AdamDIY]

+E Go Thanks for the comment. I'm glad to hear you got it up and running again!

[@rafaelrobles2349]

You saved my marriage!

[@nazmanr]

Thank you Adam I followed your detailed video and fixed it in less than 1 hour. Superb!

[@brianhicks2303]

I had EXACTLY the same problem with two broken posts on the ice dispenser switch side and one broken post on the other side. I did EXACTLY the same repair and got EXACTLY the same results. We are happy that we once again have ice delivered through the door. AMAZING. Thanks for making such a helpful video.

[@KURTMCATEE]

Your video on this issue was spot on exact problem. the plastic piece fell out when I took the cover off.There is and easier way to disconnect the wire harness from the door cover and the frig. The large five wire harness can be disconnected and leave all the wires to the door button still connected. The only hard part is getting the correct alignment for the hole you have to drill in the while plastic part to match up. Anyway fixed it and works great.

[@lugnut4961]

Thank you, Adam, for taking the time to show me your repair procedure. I just fixed mine the same way saving about $35 on a new refirgerator bracket. 8 years and you video is still helping people. Thanks again.

[@andyvasquez2358]

I went months without a working water dispenser because I was dreading calling a repairman and I was sure it would be a difficult, expensive problem. I decided to take a look myself and came across your video. It turns out that the problem you identified and fixed in this video is exactly the problem I had. I fixed it myself and the cold water tastes sweeter than ever. Thanks for taking the time to teach us.

[@vickiesposito6846]

I know this is an old post but it helped me immediately. My husband had taken the ice maker apart and found those exact little pieces had broken off. We fixed it by using some small tie wraps instead of screws. The fridge/freezer is about 20 years old but still working like a charm. Thank you!!!!

[@jasonkimerling4544]

Thank you so much for creating this video! I had just bought a $140 replacement auger motor and was very disappointed when it didn't fix my problem. Then I found this video, followed your instructions to remove the front panel and found that the plastic posts had broken off just like yours did. I reattached the switch with screws and I now again have ice dispensing from my 15 year old Kenmore refrigerator! You're a life saver!

[@redriver08]

Thank you young man! Out of three videos yours actually showed in detail how to remove the face plate. The water switch , micro switch, clicks but no water. The ice switch stills works for a frig that is 17 years old. I will order a new Whirlpool switch on Monday. Thanks again ! Ole ED

[@plummboxed]

Thanks for your subversive work! You help us get around the industry's traps. Sears charges $20 for this designed-to-fail plastic part, surprisingly cheap considering pricing of other parts (their Chief Greed Officer must have overlooked this opportunity). Your fix is genius!

[@raystampone2725]

Thank you very much. This was the exact problem my ice dispenser was having. Your repair technique was easy to follow. It fixed my machine and probably saved a lot of money !!! Thanks again.

[@michaelday1253]

Great video! I also had exactly the same problem. 3 of my 4 posts were broken and one of the retaining hooks. I used #4 machine screws with lock washers and nuts, which by the way are just the right size to go through the holes on the switch. My wife was ready to go shopping. Fortunately your video helped me dodge a $3000 dollar bullet. Thanks a bunch.

[@RL-yn3gl]

Thank you for your detailed video tutorial! My 20 yr old Whirlpool side by side refrigerator has the same problem as in your video. The ice dispenser has not been working for the past 5 years, but is still making ice, just not down the dispenser, so we just open the freezer door to get ice. You are a god send. Thank you very much again for your detailed video.

[@Engineerboy100]

I just finished this job after watching your video. Worked out perfect did everything almost exactly the same except it was not necessary to unplug all of the other wires from the front panel.

[@MichaelBonanno305]

Thank you Adam, took about 15-20 minutes in total. I didn't need to remove all the wires from the bracket, only had a problem on the ice maker site (so far). It's amazing how many people had this problem. So far in addition to this I've had to replace the optic sensor on the ice maker twice. Thanks to KZbin, guys like AdamDIY and online parts dispensers I've probably saved $600 in repair house calls.

[@thomasvanyi5209]

Adam, thanks! Thanks to your video, in about 30 minutes and with 1 screw I had my water dispenser working again. My model didn't have 2 little grooves under the front trim. Instead, I had to remove the drip tray and then 2 screws that held the black trim in place and then was able to pop it out. Great narration, high quality video, and well detailed. Glad I stumbled upon it before digging around the back of the fridge by the water line.

[@nwbig357]

THANKS ADAM! Just finished the repair and the ice is flowing again. I did one thing different. Didn't have any screws lying around so I went to the hardware store and bought 4-40 x 1 1/4 inch machine screws, lock washers and nuts. 4 of each of these. Then drilled two 7/64" holes where the pins were located. the 4-40 screws slid right through the holes, spacers and micro switches. For $1.85 both switches are now fixed. Again, thank you!

[@timvu3095]

A good video with the right diagnostics for the ice/water dispensing problem. Kenmore refrigerators are made by Whirlpool so this procedure should work for most side by side Whirlpool refrigerators as well. A couple thing I would do differently, these switches are held together to the panel with plastic guides and plastic clips, you may be able to glue them back into the panel instead of using screws. If you have to use screws, use the smallest screws that you can pass it through the switches without turning it. This way, you can replace the switches later without removing the screws. Lastly, I would not use the corrosive acid to clean the water drip tray, use vinegar, it does the same job and it is a lot safer in case you spill it.

[@webchez69]

My friend, you are a life saver..!!!! I was changing the water valve in the back for the ice maker, and decided to look into the ice motor, that has not worked in 8 years.!!! Your tips were spot on, and I would not change a thing from your procedure. The only thing I did was break off ALL of the puny little fingers so I would never have to go back in there!! Thanks again

[@clip4902]

Thanks for this fix. Could not believe I found this video with my exact fridge and exact issue with the broken plastic bracket. The screw solution works great. Saved me an expensive repair if I had called Sears.

[@808WildCard808]

Very informative and great DIY repair!!! I did not have a small enough screws so I also used zip ties for a quick fix like one of the comments below. Hopefully the ice dispenser side doesn't break too, but if it does, I now know how to fix it. Only took me 3 hours, a drill with a small drill bit, and 2 zip ties. Life's great!!! Plus I found its better to take a picture of the wire coding side of the front panel to help with seeing what connects to what instead of a picture of the connected product. Keep up the good work AdamDIY.

[@RandyL86]

Many thanks for this video! My problem wasn't exactly what yours was, but this helped me learn how to take apart the front plate and inspect the inner workings. Got the ice dispenser back working, good as new! Thanks again!

[@karlreid4200]

IN short, Excellent u-tube video AND advice. The plastic tabs were broken so I re-secured micro switch with two screws like you showed. Again, excellent advice Adam. The job went just like it did for Jeff Crockett.

[@ds8258]

Worked like a charm for me on our 18 year old Kenmore Coldspot Mod 106.50509990. Very similar to the fridge in the video though ours has two screws under the drip tray that must be removed to take off the front panel. Thank you so much for taking the time to record the video. You saved us a big repair bill.

[@ytonakao]

I have a Kenmore side by side bought in 04 and the ice dispenser stopped working. Saw your video, fixed it and voila! thanks!

[@butch12334]

Hey Adam - you ARE THE MAN!! I watched your video above and switch repair/check. My problem was that the ice dispenser did NOT work. No sound, the light did not come on when the lever pad was pushed in, no sound of the auger turning - nothing! The water dispenser works perfectly, the light works, etc. The ice maker works great! So, I noticed that you said check the 'switch' on the cube side of the frig. . . I did and I noticed that the 'hammer head' was NOT contacting the small switch part on the upper side of the switch when I pushed the ice dispenser lever inward. You said if you push the little black portion on the switch and you can hear it CLICK - the switch is probably good. The switch 'clicked' . . . so I assumed that the switch was good! The switch needed to be pushed upward in order for the 'hammer head' to make good solid contact. I had to drill a small hole on the bottom of switch (white plastic that hold the connector in place to the switch) and put in a 1/2" long screw to hold the switch upward. It worked perfectly, the ice dispenser WORKS GREAT again THANKS TO YOU!! Butch Derksen-Duluth, MN. Saved me $150.00 service call. . . .

[@sickbastd]

I love it when I fix an appliance. Gives me a real sense of satisfaction. It gets even better when my brother in law tries to repair one of his appliances without success and when he gives up and calls a repairman the repairman tells him the same thing I told him, information he promptly and bullheadedly rejected.

[@georgegray8968]

Perfect solution to a problem that has been plaguing me for about 6 months! I figure you saved me a lot of money. Thank you very much!

[@icefishingbillyable]

You saved me big bucks! instead of drilling and disassembling, I held the switch in place and heated small stainless nails up and pushed them thru the holes. once again, thank you!

[@5955trey5955]

Thank you so much for making this video. Broken pins were exactly what happened to mine. I'll provide one note that may be helpful for others... My fridge was a 2001 model whirlpool gold and my front bezel removes differently than yours. My drip pan slides out to expose two screws. You remove those two screws and the bezel just lifts off by lifting upward. This is a little easier than having to pry off the bottom first. Thought I would share in case anyone was having problems removing the bezel... Thanks again...

[@TheEkimssor]

Very helpful. I have frost buildup in the freezer around the ice dispenser port. I've isolated the cause to the ice dispenser flap not sealing around the ice port. Watching the removal of the dispenser assembly was very helpful to me. I was able to replace the damaged/worn parts and eliminate the frost buildup. Thanks.

[@Mrsolivepoop]

Thank you! followed this exactly. The only hiccup was my fridge did not have the screws to hold the entire white piece in place and it was too low to hit the switch when depressing the dispenser arm. Found some screws and secured it up high enough to hear the click, put it back together and it worked. Great video, easy to follow. Thank you so much!

[@superior_health_central]

Thank you for this video. It was exactly the problem I was having. Fixed my 20+ year old refrigerator. I thought I had a bad auger motor and was struggling to figure out how to get to it. I'm so glad it was only a broken switch housing.

[@mkmamakj]

Omgness!!! Our ice maker has not worked for about 2-3 years and I couldn’t understand why. I found your video and fixed it in a minute. Thank you! Thank you! Thank you!!

[@shawnhope81]

just wanted to say thank you. my Whirlpool's ice dispenser broke. it was identical to your insides. I did just what you did and now I can get ice again!

[@muharems2072]

Thanks a bunch. My issue was the water dispenser, the ice dispenser worked fine. Yup opened the front casing and the switch was lose. The plastic holder was broken so the switch wasn’t pressed on. My front casing was easier to take of as i had all the cables connect to a white adapter that snaps on/off so i didnt even have to unplug each red cable etc. i used one of them zip ties and tightened the switch good in place. Hooked everything back together. Plugged back my fridge on and water works great! Thanks!! Great help!!

[@ianfullmer9726]

This video was spot on. Thank you so much. Like Scott Neader below, I left the wires attached so the repair was even easier than advertised. You are doing the public an excellent service.

[@AdamDIY]

+Ian Fullmer You are welcome Ian!

[@MommaITried]

Had it fixed in less than an hour,I would've had it done in 30 minutes but it took me 30 minutes to find the right screws in the garage,thanks a million you save me money.

[@AdamDIY]

Jeff Crockett Thats fast! Yeah, it's the small things that make projects take longer. Thanks for the comment.

[@samanthajo7258]

Jeff Crockett I

[@leonardotorrealba6406]

the best explained procedure i have seen in youtube , specially because you did not change the plastic part you fix it and it was better and stronger

[@michaels7265]

It's your attention to detail that makes this a great video. Good job.

[@kstaker]

Six years later and this video showed me exactly how to fix the problem I had. My ice maker stopped working, and it was due to the switch being out of place. Thank you very much for making this video.

[@tonyhamilton9764]

Hey, I wanted to thank you very much for this video. When mine stopped working I started looking at fixes and didn't want to mess with the electronics in the front panel. I bought and replaced the auger motor but it wasn't the fix. I saw a lot of videos but none matched my fridge. Anyway, I found your video and as soon as I opened my front panel the plastic peg fell onto the ground and I knew mine was the same as your problem. I fixed it with random screws I had on hand and it works great. All this to say thank you for posting this video!

[@raulngm6163]

I really learn how simple it is to fix my ice dispenser watching your video. Thank you!

[@jenmlew]

Thank you for your video. I also used a medium binder clip to fix. For me it was faster than getting out the drill I never use. You explained very well what the problem was. Thank again!

[@robertgustafson3636]

Adam, thank you for your video. I went to Ace hardware and purchased 2 machine screws, part # A56253, that screwed perfectly into the switch. Also, you used rust and lime remover to remove the hard water stains. I have used white vinegar to do the same thing. Takes a little longer, but the vinegar is non-toxic. Thanks again, you saved me a lot of time and money.

[@naldycook5528]

Thank you, took me about 10 minutes and now the wife is happy. GREAT VIDEO !!!

[@saferiderrules]

Thank you. I just fixed mine thanks to you, but you are more adventurous then me. I used a small zip tie. it works perfect. Thanks again.

[@edwardbroadfield1846]

Thank you Adam, you saved us a lot of money, I was dreading calling a repairman, and saw your video, and even though you posted it several years ago, i was able to follow along and get my ice dispenser working again.....thanks again

[@bikemad21046]

DUDE! AWESOME. Mine has been broken for over a year. I didn't do the whole screw thing, I used a medium binder clip!!! thanks, you just save me at least $100!

[@nicolaszamora8253]

AdamDIY, your video was right on. My water dispenser was not working and sure enough the 2 small plastic posts were broken. Patched it up and now we are not thirsty anymore...=). Much thanks

[@dannyangus2980]

Nicolas Zamora A. Lot of water gets in the lower part of Refridgritator every few day but can't locate sou rocurce

[@robertloughman4134]

this was a great fix for my half-baked repair I did a few years ago with zip ties. In my case the mounting plate for the switches had play in it so the switch had to be moved forward a bit. great idea with zero cost!

[@lancebrown2823]

Thank you, I had the problem with the Water side and it worked like a charm. It only took like 15 minutes.

[@9inchsnails675]

This was fantastic. I had already ordered the switch housing and it literally took me less than 15 minutes to finish the job. I also replaced the ice dispenser flap as I had begun to see ice build up on the inside (air leak). Thanks very much.

[@AdamDIY]

Klon Waldrip 15 min! That is awesome. Thanks for the comment.

[@hodag9494]

Your video from 8 years ago made this fix easy. Thank you!

[@maryenglish6070]

You saved us about $150 you were very thorough . ice dispenser is fixed. Thank you

[@dstewart7470]

I tackled this project today because the two plastic clamps on the clear plastic ice chute has become weakened to the point in which the top of the chute would partially fall and become stuck, allowing ice to flow even after pulling your cup away. You would manually have to re-position the chute back into place to stop the flow. To fix this, I bored two small holes and used picture hanger wire by wrapping, twisting, and tucking it securely around the plastic tabs onto which the aforementioned clamps once attached. During this fix, I found that the ice was no longer dispensing. Frustrated but determined, I got online and found this video. Once I removed the panel and wires (after noting and marking them with a sharpie), I noticed both white "spikes" on the ice dispenser were broken away. I don't know if they too had become weakened over time but nonetheless I'm certain that I inadvertently broke them by pulling twisting the panel while inspecting (be careful here!) Using your suggestion, I found two screws that were just slightly larger in width and length than the spikes and screwed them securely into place (through the existing holes in the spacer and the switch). Fortunately, I was able to pull out the white housing far enough that it did not need to be removed to complete the fix. I want to thank you immensely for recording this video...very admirable!! As with most DIY projects, I'm left wondering what was saved by avoiding a service call.

[@DAILR]

thank you AdamDIY y have 1 whirpool gold series and i had the same problem ,have the two side for the relay and I see this video and repair exactly. I have for more years to use, thanks a lot and thank for take you time for help other people to repair this problems in other refrigerator, thank you so much.FROM PUERTO RICO

[@JonathanDingman]

THANK YOU! Worked perfectly. Popped it off, screwed in the screws, tested it and popped it back on.

[@yotu9902]

Thank you for your HELP your video is the BEST I found with the detail you gave us to fix and to know the workings of the unit.

[@lilglilg1493]

Adam, Great job on this video. Our ice dispenser has been broke for at least 6 month. I just found your video and my husband fixed the ice dispenser last night. The part that took the longest was finding the right size screws. Keep the videos coming! Thanks!!!

[@lilglilg1493]

+LilG LilG well, the ice dispenser is working but now the ice maker won't make ice. is there something we could have done in the process of fixing the dispenser?

[@PatiencesMom]

​@lilglilg1493 fix that sd the same way. It's just mirrored.

[@Al_Z.Heimer]

My whirlpool the same... I always wondered how to get that panel off.. thanks... It makes it so much easier to clean that area which might accumulate mold/mildew if not cleaned. Whirlpool is ZERO help. My problem is the intake in the back exterior and the back of the interior freezes up. I fixed it temporarily so many times but for some reason it continues to freeze up. Even replaced the icemaker once. I'm guessing that the valve down under the fridge is weak. Very excellent video on jury rigging what otherwise would be an expensive fix...

[@merryhoppes4246]

Thank you! My elderly parents ice maker on their Whirlpool quit, but the water spout still works. I will give it a try!

[@misuzusvideos]

Thank you for showing us how to open the dispenser! I never knew we could open it. I will see if my ice dispenser problem is a switch. Great step by step video.

[@cshawnkeech]

Thanks for the video. I ended up using a binder clip to hold the switch to the side of the frame.

[@jeannettebowen1163]

Thank you! I followed your instructions and easily fixed my broken ice dispenser.

[@ronmoore2309]

This was such an easy fix! For a few screws and drilling some holes what a money saver that will permanently fix a poor design problem. Kenmore/Whirlpool should have used used screw to fasten the switches in the first place..

[@chaddarling7471]

Just saved me another $250 to fix the cheap plastic that keeps the ice and water dispenser switch in place, thanks Adam.

[@shannonsmith8979]

Thank you for the post.... I just fixed my ice maker thanks to you :) May God Bless you !

[@kellerrobert80]

Great work-around by replacing those fragile plastic pins with steel screws. Saved time and money and they'll never break. Very clever.

[@lamaterfamilias]

First I replaced my auger motor and that didn’t fix it, then I watched this video and my problem was identical. Thank you!

[@Travis_125]

Thank you! Same issue and same process in fixing it. The only difference was that I was lazy and drilled the holes with the wires still in tact - bracket still on the fridge. Worked perfectly!

[@robertgunter3997]

I have the same dispenser with the same problem. This helped tremendously. Thank you!

[@dominicebert5606]

Thank very much Adam, easy to follow video and I fixed my ice dispenser thanks to you.

[@mailterry]

Perfect video to fix my icemaker, I ordered the $16 bracket instead of using screws, but why doesn't the manufacturer make it with the screws to start with. It would last a lot longer, oh yea, then they couldn't sell you a replacement or charge for a service call by the company repairman!

[@kevinpaulson339]

Hey thanks for video, had the exact same thing going on. I was thinking the ice maker itself was the culprit and was going to replace it. Plus now I,m a hero in my wife's eyes, told her she has to keep me:)

[@marknemec7082]

Had a little different problem couldn't shut off the water dispenser. Not sure what actually happened but I did find a broken post and used your repair, worked like a charm. I put it back together and it worked like a charm. Thanks good fast fix!!!

[@AdamDIY]

Interesting. The switch must have been stuck in the ON position. I'm glad you got it working again!

[@donnazy1]

I also fixed my water dispenser with two screws. What a great video. Thank you.

[@2muchdance1]

Dude I just did this repair and it worked PERFECTLY!!! thank you so much!!!!!

[@sampsin1]

Thanks! Excellent video saved me some money and time. Same exact thing broke. Planned obsolescence.

[@karenmoore2551]

Thank you, AdamDIY for taking the tile to post thios video. Although my Whirlpool was a little different, I was able to make the repair using your screw idea. It worked like a charm. I know I saved a ton of money by doing it myself. A repair person may have suggested I buy replacement parts, and I would have had to pay for labor and a trip charge. Thank you, thank you, thank you!

[@AdamDIY]

Karen Moore Thanks for your comment Karen. It's nice to hear success stories!

[@Jerinelle]

Karen Moore

[@nickymack1236]

Hi Adam, just letting you know that I watched your Video with pleasure. My Ice and water dispenser not working. You gave me an idea how to fix it. Tomorrow I will try to open to see what the problem is. I will let you know the outcome. Such a great information and thank you so much. *A*

[@AXNJXN1]

Excellent video... Will be tearing mine apart now! Thank you Sir.

[@hardin1271]

Outstanding help video. I was actually working on the auger motor but the steps in your video for fixing the switch housings was perfect. I even watched the whole AD that popped up so you'd get paid if you're connected to AdSense. Thanks for taking the time to make that video.

[@nazmanr]

Thank You Adam you saved me a trip from the repairman and it took less than 1 hour. Superb.

[@mikeb6386]

Thanks those plastic guides on mine broke too. It's fixed thanks to u and will never break again.

[@paulbrown6269]

And it just worked for me! This video is the gift that keeps on giving!!

[@albertandrada6096]

Thanks you probably saved me a lot of money and it was not that difficult to do. Everything works fine thanks to your video.

[@bg147]

That was not built to last.Very resourceful approach.

[@coloartist]

Thanks! Helped a lot in diagnosing the issue. I opted for the new replacement part from SearsPartsDirect for $12.21. I figured all the plastic in the plate was bunk back then, and would go big.

[@Sp00nMan]

Thanks so much for this. Exactly what just happened to my icemaker side. Glad it's an inexpensive repair!

[@waynedavis3116]

thanks man... i have a whirlpool side by side and same exact thing plus the snap in part was broke... just took me 20 minutes and it is repaired.... thanks a bunch

[@fuigarious7]

Thanks for the video Adam, mine broke and I was thinking of gluing it but that wouldn't have worked very well. Used your method today and it worked like a charm!

[@azppmd]

Disassembly instructions led to ability for me to diagnose and find a temporary fix to the problem. Thank you!

[@360efi]

Just a tip, You can always use your phone to snap a picture of the wires so you don't have to remember the color or sequence. Its helped me many times from car repair to other electronics as well

[@geterdun57]

Just fixed the ice dispenser in less than five minutes with two old screws I had lying around. Thanks for the great video!

[@AdamDIY]

+Blake Owen That's got to be a record!

[@tonysantamaria19]

I had a broken peg on the ice dispenser switch also, I used a screw as you showed here. I hear the switch clicking now, but no motor sound, not even a hum. I emptied the ice bin, still no motor sounds, not turning the auger. I tried to turn the auger manually, and it turns freely enough. It's a Whirlpool side by side with dispenser on door like yours.

[@robertgustafson3636]

If you take out the motor for the auger. While taking off the spindle, if dont feel any resistance, your motor also will need replacement. If you decide to purchase on-line. Go to Sears.com, you will be able to purchase at less then half the price as whirlpool.com

[@mikecollins5174]

Thank you, Adam great job on video. You saved me a lot of frustration and time. My Ice maker dispenser was not working. It was exactly the same problem as yours. Thanks again and great fix. I think the screw modification was great ideal, probably more stable that original plastic post.

[@rg689]

I had the exact same issue with the ice dispenser. You saved me a lot of time and money! Thanks so much!

[@efficiencygeek]

Thanks for posting this. Same problem on my Kenmore. Drill and screws saved the day. Had difficulty removing the front plate / control panel. Must have calcified due to age of the fridge. Also, instead of removing each wire on the control panel, was able to detach using the wiring harness connector. Thanks again. :-)

[@AdamDIY]

+EfficiencyGeek I am surprised at how many people are having the same problem. It's obviously a design flaw. Glad to hear you got it working again!