no problem! Subscirbe for more! I intend to make a lot more videos about the Lynx coming up soon!
@jomme9186 ай бұрын
nice done. Are there any known issues of water or dirt getting in the bearings,, expecting my lynx 05-april-2023,, @@brianonwheels
@Riceman-o1p9 ай бұрын
Crunchy button is easily resolved with graphite powder. Ewheels gave me a new button panel but I didn't need it. 700 miles on my new wheel and it is problem free.
@nomadmusk9 ай бұрын
No sealant is a mistake, that is your last line of water resistance defence (aka dropped in a puddle), other teardowns show silicone there. I would add it as its not something you need to undo often, and stays in tack for tire changes.
@brianonwheels9 ай бұрын
thanks for the advice! I order some sealent here: www.amazon.com/dp/B08B5YFJMV?psc=1&ref=ppx_yo2ov_dt_b_product_details I'll reapply the sealent around the battery cables but it really didn't seem like there was sealent anywhere else
@nomadmusk9 ай бұрын
@@brianonwheels I realize this is a Patton, but they don't do new videos if its really similar. They basically say put it around the edge of the cover. kzbin.info/www/bejne/bqKYg5x_id10gdksi=Rwt0t69vKF14O3xZ&t=263
@brianonwheels9 ай бұрын
@@nomadmusk Leaperkim actually improved this design learning from the flaws of the patton! You can see that there is a raised metal wall around the board and it's no longer flat like the patton is. So they no longer need to rely on silicon to seal the cover around the board, only a bit of silicone is applied where the battery wires come out
@nomadmusk8 ай бұрын
@@brianonwheels yes definitely a great improvement for rain proofing, but idk if I'd trust it if I fell in a puddle, or if it fell off a little stream bridge. The reason it was there in the first place was because that compartment is not water tight.
@richsam2873 ай бұрын
I would recommend disconnecting battery before gaining access to controller compartment. Just dropping a screw on your controller could make fireworks.
@JarerSaro6 ай бұрын
oh the lcd flat wiring some of it disengaged you need to replace it; also the water will sip in once you open it and assemble back, to make sure put a silicone compound around the lcd and whole cover fittings to lock the gaps protect from rain
@grb19699 ай бұрын
LeaperKim needs to design a $0.001 spring to help return the button to its neutral position. The rubber button is getting stuck within the edge crease of the material and the toggle-button on the display board wasn't designed to have sufficient spring force to return the rubber into position. Temporary fix: use hot glue to stick a nub-handle (like a chess-pawn piece) to the outside of the rubber and slightly pull after pushing to power on. {Second, seal the top cover edge with GE-type2 Silicone caulk, every time you open the control board cover.}
@brianonwheels9 ай бұрын
ewheels gave me a new top panel that fixes the button! It works well now! If you look at the end of the video the button is fixed!
@InsanitiesBrother9 ай бұрын
Another thing people need to do is use loctite on the battery fuse bolts.
@brianonwheels9 ай бұрын
I'm aware of this issue but it doesn't seem like my model is experiancing it yet! I'll post a video about it if I get the issue. subscribe so you that you get notified if I run into that problem
@pacochawa27469 ай бұрын
Hope they sove this in next batch. Sad to see so many problems. The wheel has potential. Paton and ss dont have these issues? Must be a bad year for production... Its nice ewheels is on it. Spending this doe on it and no support would be worse. Its good ewheels does the effort.
@gabinator11779 ай бұрын
Just raise the toe pads to a higher setting if you don't like being locked in so much. Getting your feet stuck isn't much of a design issue since that can happen with any pad setup with a very tight toe area.
@brianonwheels9 ай бұрын
Thanks! That's what I ended up doing and I also bought an aftermarket toe pad that works wonders. Subscribe so that you see that video when it comes out!
@fqqures10199 ай бұрын
I would be mad spending $4k and having these issues Did u see these issues soon after you got this euc Did the seat come with the lynx?
@Riceman-o1p9 ай бұрын
Mine has the same problem. It started after about two weeks of ownership but the button never gets stuck it's just a little crunchy. So it has never given me a problem. I've applied some silicone lubricant to the button and it appears to be getting better. And yes, when I purchased mine from E wheels they provided me power pads and a seat with my purchase. And the seat is really high-quality, it's very nice.
@nomadmusk9 ай бұрын
Every wheel has had issues, and china is gonna china. As an s22 owner, I'm jealous as hell haha. This is pretty fixable without replacement, and the company isn't even fighting customers on replacement.
@EkoKolo_Katowice9 ай бұрын
Some Dremel work and button will work fine I think . This screen of death happen me few times in Sherman OG . Nothing done yet . Nothing important .
@matthewearl98248 ай бұрын
The light button doesnt work sometimes also. Ewheels overnighted me a new top panel. They are the best.
@bobelminero14278 ай бұрын
great video
@usmcmsgt54878 ай бұрын
How do you know if you have the first batch....? I want to purchase the veteran lynx 62 lbs suspension but don't want the 1st batches...... Looking at buying one in the next couple weeks.
@brianonwheels8 ай бұрын
Ironically it seems like batch 2 is facing more issues than batch 1 and now they’re skipping directly to batch 3 in March
@nicod9749 ай бұрын
Use conformal coating on every pcb except for connectors.
@curtflirt29 ай бұрын
Don't take any chances, contact E-rides and maybe see what Afeevs can do
@greenwave8198 ай бұрын
There are no known or unknown issues with the Lynx. It is very well known that Leaperkim is superior and they only produce perfect wheels.
@familytvbox52188 ай бұрын
Ahhhha, no.
@kabosune90979 ай бұрын
How do you like that Beidou seat? I was thinking about getting the leather one on Etsy. Is the trolley handle easily accessible?
@brianonwheels8 ай бұрын
It’s great! Highly recommend just fillip the seat forward and you have trolley access