Install Of Senders on small block with introduction

[@biartchnicyndi]

Very good clear explanation on the video, well done

[@caemaridwn]

2:21 it all became clear why mine din't work "Doh".Thanks

[@wrenchops719]

Nice crossfire renegade manifold! I know the guys who developed it!

[@mototrxsr3846]

Is it a must that the water temperature unit be on the side of the block or can it be at the front on the intake close to the water pump?

[@hkmoney6220]

This is the most awkward guy on the planet.

[@rickigunter1960]

He's funny..he looked like he felt stupid explaining something so simple..lol

[@johnfair62]

Good job! Thank you for the help.

[@Intellitronix]

Hello John, you are very welcome. Please let us know if we can be of further assistance. Your Intellitronix Team!

[@brandoncasares7624]

Thanks very useful !

[@gustavette8487]

Great video. I read somewhere that inside the orifice where you screw in the new sensor, there is a pin that inserts into the tine hole of the new sensor while you are screwing it in and that i should be careful not to damage that pin when you take off the old sensor. I am asking because I removed mine (C3 1978) and do not see any pin... Also, if there were a pin, how would the oil flow???

[@patriciasalaciak8495]

Hello Oceanpointe Distributors Corporation, you can contact Customer Support at 440-359-7200 ext 214 or email [e-mail] or the Help Desk at 440-359-7200 ext 201 or email [e-mail] and they will be able to answer your question. Thank you! Your Intellitronix Team!

[@vetteseller5]

perfect info, thanks

[@davidmckibbin4440]

your great , thank you very much

[@Intellitronix]

You are very welcome!

[@thomaswilsonsr.9206]

Hey. I can't find the connector on my harness for the oil pressure sender. You wouldn't happen to know what the connector looked like? It's from a GM vehicle, 1978 pontiac. I rebuilt the motor, and it seems as if I can't find the wire for it. I have the Temp sensor connected, but not the oil pressure.

[@Intellitronix]

Hello Gage, How are you? Did you get your issued solved? If not, send an email with your problem to our tech guy at [e-mail]. Please leave all of your information so we can get back to you in a timely manner. Thank you again for your support and we want to let you know we appreciate you and your business.

[@jwash2511]

I have a 1997 Chevy C1500 WT. I purchase the DP6007 kit which requires the oil pressure and water temperature sending units to be replaced. After replacing the oil pressure sending unit I encountered a no start problem. Later found out that the oil pressure sending unit energizes the fuel relay. What is the workaround for this issue?

[@ericdawson9104]

Was it easy putting the intellitronix speedometer in?

[@josephwashington7040]

@@ericdawson9104 I purchased the intellitronix GPS speedometer which requires no calibration, just connecting several wires. This was much easier to install and has better accuracy than using the OEM speedometer connection.

[@ericdawson9104]

Okay because I purchased the intellitronix speedometer DP6005and just wondering.

[@josephwashington7040]

@@ericdawson9104 I installed the DP6007 kit which was pretty straight forward except for the installations of oil pressure and water temperature gauges. Instead of mounting them per the installation instructions, I mounted them in the extry oil and temperature ports on the bottom left of the engine block. Don't know what engine you have but I have the 4.3 six-cylinder.

[@ericdawson9104]

I have a 5.7 v8.

[@nicholasyoder]

So that’s it no wires connect to the oil sending unit?

[@Intellitronix]

Hello Nicholas, you can contact Customer Support at 440-359-7200 ext 214 or email [e-mail] or the Help Desk at 440-359-7200 ext 201 or email [e-mail] and they will be able to answer your question. Thank you! Your Intellitronix Team!

[@mr.sinaloa1760]

What about for big block ??

[@marcuspurvis2897]

how do I connect the oil pressure sending unit to the gauge cluster?

[@kj9219]

You screw it. Real good.

[@jamespspivak247]

Hello Marcus, You can download the Installation Guide for your vehicle and it should explain how to connect the sending unit to the gauge cluster. Let us if you need additional help by emailing [e-mail] Your Intellitronix Team!

[@Intellitronix]

Hello Marcus, You can download the Installation Guide for your vehicle and it should explain how to connect the sending unit to the gauge cluster. Let us if you need additional help by emailing [e-mail] Your Intellitronix Team!

[@marcuspurvis2897]

Intellitronix Corp. this was 2 years ago

[@Intellitronix]

@@marcuspurvis2897 Yes, and obviously the person who had responsibility for KZbin 2 years ago did not answer the question. We are working on creating animated videos for the 6 main gauges to help customers with their install. We will post once they are done. Your Intellitronix Team!

[@StayFancyRide]

Soo, where do I connect the speed sending unit?

[@kasp8407]

how do you put the wires in the oil pressure sending unit i have the two port unit

[@shawnslenski3013]

One post has a S = signal wire, other has a G = ground, run to engine block

[@kasp8407]

@@shawnslenski3013 No what i mean is the two wire ports screw off do you stick the wires through them or take the ports off rap the wires around them and screw it back on? i never seen ports on a sending unit like that. thats why I am asking

[@nickythebull82]

What about the Ford Mustang 4.6 having some issues over here

[@Intellitronix]

Hello Nicky, could you give us more information about the type of issues you are having with the senders on your Ford Mustang 4.0? Thank you!

[@nickythebull82]

Intellitronix Corp. The sender is fine I got the package the installation is a pain in the butt the directions aren’t too detailed why do I have to use the oil pump and the coolant replacement or can I use factory

[@Intellitronix]

@@nickythebull82 Hello Nicky, I spoke with the Support Technician and he said that you have to use Intellitronix Oil Pressure and Water Temperature senders, because the senders work with Intellitronix gauges. If you have additional questions, you can contact Jim Fultz in Technical Support at 440-210-7646 ext. 203 or 440-359-7200 ext. 203 or email [e-mail]. Jim is very knowledgeable and will be glad to help you. Your Intellitronix Team!

[@nickythebull82]

Intellitronix Corp. ty

[@Hammy1088]

Where can I get that oil pressure adapter?

[@Intellitronix]

Hello Abraham, you can purchase the adapters in hardware or automotive parts stores. For further information, for technical questions please call Technical Support at 440 210 7646 ext. 203 or 440-359-7200 ext. 203 or email [e-mail]. Your Intellitronix Team!

[@buddyroper1174]

Where can we buy the adapter

[@Intellitronix]

Hello Buddy, you can buy them at any hardware store in the plumbing section. If you need further assistance, please call Jim Fultz in Technical Support at 440 210 7646 ext. 203 or 440-359-7200 ext. 203 or email [e-mail]. Your Intellitronix Team!

[@jnasiatka85]

Tachometer?

[@Intellitronix]

Hello Nasiatka TV, for questions regarding the Tachometer please call Technical Support at 440 210 7646 ext. 203 or 440-359-7200 ext. 203 or email [e-mail]. Your Intellitronix Team!