Installing a Thread Tension Release Guide

  Рет қаралды 20,112

Uwe Grosse

Uwe Grosse

Күн бұрын

Пікірлер: 39
@john-henryjohnson4077
@john-henryjohnson4077 8 жыл бұрын
Haha dude I just spent a few hours figuring out how to do this... then I find your video. your videos are great! I have not found anywhere else that explains this this well! thank you! !!
@aquilaleathercompany9891
@aquilaleathercompany9891 7 жыл бұрын
Thank you so much. I just purchased an old Consew 226 and have this exact problem. Just ordered the part to replace. If I could give ten thumbs up, I would :)
@boutch050
@boutch050 11 ай бұрын
Excellent video, I tried to change to Adler 269 now and I found that this part was not in my machine at all, thank you very much, it helped me a lot
@bizeigel
@bizeigel Жыл бұрын
Most excellent! Some notes: I zip tied together the spring, tension release slide and tension bracket and then cut once I had in position. I also found it necessary to remove the lifting rock shaft link in back in order to get the lifting bell crank back into place(the one that goes onto the three bushings or links simultaneously.
@juanrivas6048
@juanrivas6048 Жыл бұрын
Este es un trabajo muy Profesional Gracias señor , Yo quiero decirle que Gracias a usted yo ya soy un mecánico de máquinas Gracias míster le estaré agradecido por el resto de mi vida , Gracias por esa Gran paciencia que tiene para mostrar sus video Muy profesionales
@ibsoarin
@ibsoarin 8 жыл бұрын
Excellent video. I will have no qualms about this repair now. I appreciate the temporary mistakes you include in your videos. The "mistakes" are just as important so I do not have to make them. I would assume that a Singer 211G155 will be another machine which might need this repair. Thank you for your time, effort and expertise in these videos. Mark.
@AlexanderDyer
@AlexanderDyer 8 жыл бұрын
Thanks for such a well lit, edited and captioned video.
@Skellyman99
@Skellyman99 6 жыл бұрын
Alexander Dyer great video! Just discovered it. Can you tell me (before I take my Consew 206-rbl18 apart (to check this part) ...how much (ie: measurement / mm’s) is the thread tension release stud supposed to come forward when the presser foot is lifted. I am getting some tension release but it seems like ‘not enough’?
@slimmers00
@slimmers00 3 жыл бұрын
Thank you so much for sharing this video. This is what’s wrong with my singer 111w155 and I was really intimidated by the repair
@juanrivas6048
@juanrivas6048 9 ай бұрын
Muy profesional Gracias
@atwateratelier6139
@atwateratelier6139 6 жыл бұрын
Thanks a million! replaced it without a problem.
@juanrivas6048
@juanrivas6048 Жыл бұрын
Thank you mister Uwe Grosse
@juancarlosduque6114
@juancarlosduque6114 3 жыл бұрын
Excelente video, Tengo una Pfaff 546 con el eje principal doblado donde va la correa ( por un golpe), alguna recomendación a la hora de desarmar la máquina para enderezar dicho eje?. Gracias
@justindaniel2371
@justindaniel2371 6 жыл бұрын
I don’t think my part is broken but when i lift the foot the pin pushes minimally. Also, i am wondering if the foot lever and linkage are supposed to be moving up and down while the machine is operating. Thanks,
@keeprighthanddown
@keeprighthanddown 2 жыл бұрын
such a great video..
@jarrittflinn1635
@jarrittflinn1635 5 күн бұрын
thank you so much !!!!.......you da man !
@horaciocastillo1435
@horaciocastillo1435 8 жыл бұрын
This video came from heaven to me.I do have to replace this guide on my JUKI 562. My problem is where do I find this part on line. Can you please give a clue if you have one? Thanks so much for this wonderful video.
@UweXY
@UweXY 8 жыл бұрын
Just type the part number B1461-053-0A0 into a search engine and you'll likely be presented with a few options to buy the part, depending on where on the planet you live. I'm pretty sure I ordered mine from ABC Sewing Machine in California (www.abcsewingmachine.com/products/b14610530a0-thread-release-guide-asm) for around $10 plus shipping.If you're in Europe, College Sewing in the U.K. (www.college-sewing.co.uk/store/B1461-053-0A0-THREAD-RELEASE-GUIDE-LU563) is a good option. I recommend using the original Juki part - it's noticeably better quality than the aftermarket replacement parts. You'll be spending an hour or two replacing it, so $10 is a good investment in a quality part.
@horaciocastillo1435
@horaciocastillo1435 8 жыл бұрын
Thanks so much again,I just ordered the part from ABCsewingmachine in Los Angeles,California,it was $12.47 w/shi. to Florida.Used Pay-pal to pay. I did time my machine thanks to another one of your videos, so this is the second time I do get help from you. Thanks again,Merry Christmas to you.
@cccodfish
@cccodfish 8 жыл бұрын
Nice....thanks.... question ...were can I get those screws for holding the feet on? I change feet all the time and struggle with the slotted small screw..
@UweXY
@UweXY 8 жыл бұрын
I sell slotted thumb screws for mounting presser feet on the out presser bar on Juki LU-563 and many other machines. The same screws can also be used for attaching the swing-away cover plate on the left side of the machine head. Check out shop.uwe.net
@jaiv2001
@jaiv2001 8 жыл бұрын
hi. do you have a video on replacing the take up spring? i just bought a new one and have taken my assembly apart. but, the screw that the spring sits on...or around i should say, will not come off. does this need to come off to get the new spring in place?
@UweXY
@UweXY 8 жыл бұрын
That's not a screw, it just looks like one. Study the parts diagram to find out if something is really a screw or not many parts have slots that make it look like a screw, but it's not. It's really a shaft that's held in place by a set screw. Loosen the tiny set screw behind the tension unit at the bottom right. The shaft should pull straight out. Then you can replace the spring, and re-insert the shaft. Tighten the set screw again just enough to hold the shaft a tiny bit. Insert a screw driver in the front slot and turn counter-clock-wise until the spring has the right tension. Then tighten the set screw again. I usually replace the entire tension unit, they're cheap at around $15 even for an original Juki one.
@jaiv2001
@jaiv2001 8 жыл бұрын
+Uwe Grosse got it out! thank you
@cancelik
@cancelik 6 жыл бұрын
Can you figure out the function of the small spring between ''tension release guide'' and ''presser bar lifting bracket'' (its name from consew 225 parts manual)? It's hard to understand.
@cancelik
@cancelik 6 жыл бұрын
ok, I thought and found it I think. It is for preventing pressing foot lifter (doesnt matter it is knee lifter or foot pedal) move up and down. preventing vibrations and noise.
@samperarcosdelgado1016
@samperarcosdelgado1016 4 жыл бұрын
Excelente vídeo gracias
@justindaniel2371
@justindaniel2371 6 жыл бұрын
What if the part isn’t broken but the bar doesn’t move forward enough to release the thread tension?
@danielostrowski1148
@danielostrowski1148 5 жыл бұрын
Check and see if you have a tension release plunger in the tension stud of the tension assembly. It's a tiny little "T" shaped thing that is enough to mess this up. Link is for one for a consew 206rb southstarsupply.com/product/26-tension-release-plunger-10686-10793/
@leecopp8012
@leecopp8012 8 жыл бұрын
Thanks Uwe, another great video. Wow, had to get in there a kinda deep. You do an amazing job with clarity and focus .. what kind of camera are you shooting with? Lee in Florida
@UweXY
@UweXY 8 жыл бұрын
+Lee Copp This particular video was filmed entirely with my iPhone 6. Lots of light, a tripod, and iPhone focus lock (touch and hold the area on the screen you want to stay in focus) are the main tools I employ to get the clarity I'm after when making these videos. In other videos I had also used a Canon 70D with a 100mm macro lens to get REALLY close to something.
@dgzee66
@dgzee66 5 жыл бұрын
Is this the same way for a singer 111W153?
@UweXY
@UweXY 5 жыл бұрын
The Singer 111W153 appears to have nearly identical mechanical bits inside the head. You should be able to follow the same basic procedure.
@dgzee66
@dgzee66 5 жыл бұрын
Great, do you have a good source for a quality part?
@UweXY
@UweXY 5 жыл бұрын
@@dgzee66 I bought the OEM Juki part from www.abcsewingmachine.com/
@silaimashinewala5392
@silaimashinewala5392 7 жыл бұрын
762 juki machine cotter setting please
@cs-rj8ru
@cs-rj8ru 2 жыл бұрын
I saw this guy at an auction once. He was carrying/wearing a leather man bag.
@UweXY
@UweXY 2 жыл бұрын
I’m not sure who you’re referring to, but it wasn’t me. Note sure how this would be relevant, either.
@emccat
@emccat 3 жыл бұрын
Ah ha! I see you have one already!
Thread Tension Adjustment Explained
12:08
Alexander Dyer
Рет қаралды 138 М.
If people acted like cats 🙀😹 LeoNata family #shorts
00:22
LeoNata Family
Рет қаралды 45 МЛН
Mom Hack for Cooking Solo with a Little One! 🍳👶
00:15
5-Minute Crafts HOUSE
Рет қаралды 22 МЛН
Try this prank with your friends 😂 @karina-kola
00:18
Andrey Grechka
Рет қаралды 6 МЛН
Consew 225 Hook Timing
11:50
Uwe Grosse
Рет қаралды 340 М.
Juki LU 563 Instructional video
14:43
Gran Strachan
Рет қаралды 138 М.
Juki LU-562 Unison Feed Explained
6:27
Alexander Dyer
Рет қаралды 52 М.
Adjusting Juki LU-563 class machines
12:32
Uwe Grosse
Рет қаралды 206 М.
Juki Lu 562 - 563 Industrial Sewing Machine maintenance video
32:17
Bridgewater Sewing Centre Ltd
Рет қаралды 50 М.
Juki triple arrastre LU 563 cambio de lanzadera y algun datazo
57:02
GUFER Gustavo Fernandez
Рет қаралды 15 М.
Singer Safety Clutch
9:33
thumpr2good
Рет қаралды 38 М.
Safety clutch on Singer/Juki/Consew industrial sewing machines
7:15
If people acted like cats 🙀😹 LeoNata family #shorts
00:22
LeoNata Family
Рет қаралды 45 МЛН