Installing CV boot using a clamp tool

[@madcat4563]

Thanks a bunch.

[@simplelangperorock]

The forward-reverse moment is hilarious. Thx for all

[@rob12449]

yup, today I'm planning to use the same tool for the first time, I know there is winding and folding but did not know about the cutting feature. It is good to know how to use a tool before using, and reading directions is not a bad thing, sometimes you can criticize the directions for being confusing. youtube is the best thing since sliced bread.

[@koitorob]

I recently bought a pair of CV boot clip tools. One identical to yours and a different one that pinches a 'square hoop' shaped part of the boot clip. Not realising that they were for different types of boot clip, you've just stopped my head scratching in confusion! Thanks!

[@hav1byte]

Great video- just what i needed to know/learn, the band tool, for same right rear axel on my machine which i need to fix - thank you

[@lookoutleo]

Excellent tool much better than using nail plyers and side cutters on the old clamp, must get that , thanks for posting

[@vinces8974]

Great demonstration, I think you needed a bigger hammer though LOL

[@canuckfixit7722]

Just bought the 8milelake CV joint banding tool from Amazon and I have not had the chance to use it yet so I appreciated your demonstration. I think that the orientation of the clamp to face backwards is actually a good idea (no one else has hinted at that yet). Rebuilding the CV joints on my Honda Element.

[@thecompulsivecollector1472]

This was helpful, thanks!

[@jamiejazzy]

Very helpful,didn’t know there was a tool but that looks handy👍

[@whynotjusttry5401]

Thanks for watching.

[@SKILLS2KILLS_QC]

Hi me and my steo dad aer trying zo do the same job on a 2002 375 and we are stuck on trying to get the knuckle off the outter part of the axle any tips buddy

[@paulandrews3785]

thanks for the video got this tool for doing heat 🔥 bandage suppose it will work

[@koky7288]

Dont forget to remove air trapped in boot before clam install.

[@sailorbob74133]

Thanks, been a while since I've replaced a cv boot and couldn't remember how to use the clamp tool.

[@leod3963]

Great video man

[@whynotjusttry5401]

I was trying for short simple how to use video, because that’s what I look for when I need help.

[@texassmokingmonkey]

Nicely done. I pulled my outer CV acle out too far so had to pop the clamp to get it back in. Tried just a regular hose clamp, but the tightening fitting sticks up too high, and would have destroyed an electrical fitting after one rotation! Glad to find this, very useful.👍

[@whynotjusttry5401]

I’m glad it helped. Thanks for watching.

[@hav1byte]

Also, just fyi - suggestion- maybe cut off the corners of the band tabs, or round them off - wont be pointed or sharp

[@whynotjusttry5401]

Good idea. Glad the video helped.

[@rawbdiggity]

Good video, thanks

[@RocksNRuts4]

need to do the same as i see gease in my rim, how do i kno cv joint is bad, grinding n stiff?

[@whynotjusttry5401]

If you can rotate it and it’s smooth. If you clean out all the grease and look at it for any issues.

[@RocksNRuts4]

@@whynotjusttry5401 ty, does seem smooth but old grease is slightly silver so thought maybe shavings...

[@chiefer8368]

Where’d you get ur crimping tool? Video was quite helpful too as I wanted to see this done up close. Thanks.

[@whynotjusttry5401]

I purchased the tool from Amazon.

[@whynotjusttry5401]

There is also an Amazon link in the description for you to find it easier.

[@winandd8649]

Instead of figuring out which direction your axle is going to turn when installed, you can also bend back the remaining lip to be clamped underneath the 2 tabs, see : kzbin.info/www/bejne/ooLHdoCnnJiNmrs

[@whynotjusttry5401]

That works too. Thanks for sharing.

[@RocksNRuts4]

thought he did that...

[@kevinparker5657]

Nice shirt