Installing Pipe Flashings on Metal Roofs

Рет қаралды 87,669

Жыл бұрын

This video will tell you about the correct way to install pipe flashings on metal roofs. This is one of the most important things when installing metal roofing, as this is one of the most common areas for leaks.
Go to www.RoofingIntelligence.com to watch the complete 14 video series on installing metal roofing.

Пікірлер: 37

@roythurston7799 Жыл бұрын

Best video I’ve seen on metal roofing problem areas so far.

@dankaufman5594 Ай бұрын

Thank you so much for making these videos. You answered all of my questions for installation of a metal roof over shingles but more importantly we are getting an estimate for installation so I know what questions I need to ask. If we end up doing this ourselves I'll watch the videos several more times.

@eliascastillo3838 5 ай бұрын

Man this guy is a good roofer,a comment from a roofer too.

@tjbergeron 7 ай бұрын

Thanks for putting these videos out.

@RoofingIntelligence 7 ай бұрын

Glad you like them!

@chriswerkes8313 Жыл бұрын

Great video. At <a href="#" class="seekto" data-time="637">10:37</a> you illustrate many screws to hold the flashing down. I know from firsthand experience that that snow and ice can lift that flashing up and cause leaks because I only had six screws holding it down. I am going to drill it the same as you did to repair it.

@kroth14 Ай бұрын

Very thorough instructions. Thank you

@rowgler1 13 күн бұрын

You explain things well.

@mikewatson4644 Жыл бұрын

Thank you. Very good instructions.

@Kerfufflekitten Жыл бұрын

Thanks, I’ve always wondered if they made a heat resistant boot as those steep metal flashings are a pain for me as a plumber.

@joeolsen3553 5 ай бұрын

You always have good videos. I learn some good information. Much of it I know already but still enojoy videos. Thanks.

@RoofingIntelligence 4 ай бұрын

Glad to hear it!

@TheDavidscc32 Жыл бұрын

I have a power mast pole that runs through my roof decking. If I were to reroof with exposed fastener roofing like this video shows, would I be best off to do the second method with two sheets of metal? And use the last boot you showed in the video?

@RoofingIntelligence Жыл бұрын

You're 100% correct! You'll need to pieces of metal and the split pipe boot.

@jimacheson4933 Жыл бұрын

Just what I was looking for! Metal roof flashing where there is a ridge in the way. Very well explained. What would you do if you need to install screw eyes into the metal roof, will metal roofing caulk be enough around the screw eye that will be used for down guy? Thanks!

@josemondragon382 Жыл бұрын

Muchas gracias por dar este video se aprende mucho gracias y sigo viviendo sus clases

@RoofingIntelligence Жыл бұрын

¡Ningún problema! Me alegro de que hayas disfrutado el vídeo.

@ty0285 Ай бұрын

I was told from the company I bought my roof from, that those silicone heat resistant boots aren't actually approved. I have to use a metal boot for my fire place vent stack.

@noahschmartz2354 4 ай бұрын

top class,

@rkgordon3 9 ай бұрын

Who makes the rubber boots with the soft aluminum edge?

@toddrhine7648 9 ай бұрын

Hi there, I just saw your video now and liked it. Please can you tell me what's the best type of sealant for the flashings per retrofit boots/Whirly bird flashing on metal roofs. Thx much

@RoofingIntelligence 9 ай бұрын

I'm a big fan of Solar Seal brand.

@toddrhine7648 9 ай бұрын

@@RoofingIntelligenceThx much. Looking to purchase a great (Furnace) Heat Stack Boot kit for my metal roof. Metal will be installed on perlings over roof shingles. Can you direct me to a great kit please? Thx so much.

@dethmaul 11 ай бұрын

I heard that you should put square flashings over pipes diamond-like, with the point facing up. That way there's less xhance for water to in trude, because it will run off instead of sitting on the flat bit. Does it make that mich of a difference, or is it a waste of time?

@bluegorillacookies 8 ай бұрын

I don't think it would be a waste of time because it doesn't take any more time than installing it the other way.

@MariusSchilder Жыл бұрын

What to do if the vent pipe happens to penetrate right at the edge ridges of two joining sheets? Put a third sheet over the middle, from ridge line down to a bit past the vent?

@charlesburt7778 Жыл бұрын

13:22 should help

@zeropapa900 10 ай бұрын

What if my pipe flashing falls just on a seam for the next panel?

@offgridliving4128 9 ай бұрын

I want to metal roof over my existing 3 tab. I have watched every video on flashing. But I can’t find any to deal with ceiling fan vents. I’ve seen videos that they just remove them and let the air vent under the metal panels. I don’t like that idea. Plus I would prefer not to damage my existing roof as it’s only 4 years old.

@larryfisher4290 Ай бұрын

where do u get these things ? can't find em. how about some one showing how to put on ahard one instead of an easy one anyone can do!!!!! I got one that fits ontop of two ribs and one of those ribs is where the two pieces of tin join. explain that one!