Here’s a video showing the installation process of installing the newly released CNC billet gimbals into my V-Control Evo Transmitter. They are super smooth, I’m very happy with how they feel.
Пікірлер: 32
@skey19759 ай бұрын
Thank you for taking the time to make the video. I will use this as reference when my gimbals arrive.
@marcossallua198410 ай бұрын
Great video Rob. Congratulations !
@MrRctintin10 ай бұрын
Thank you
@CaptainCrash99910 ай бұрын
Great video Rob and very informative! I’m sure lots of people will utilise this to carry out the gimbal swap on their VControl
@MrRctintin10 ай бұрын
Thanks 👍
@seanoc35339 ай бұрын
Very helpful as always, thanks Rob!
@bigdigger2410 ай бұрын
Sir Rob, awesome vid ,definitely helpful,thanks
@MrRctintin10 ай бұрын
Thanks Bill
@markritchie90810 ай бұрын
Great info and great vid Rob... Many thanks... M
@MrRctintin10 ай бұрын
Thanks mate
@luismartincordero80786 ай бұрын
En la vbar me a dado fallo , a usted le pasado. Q se puse hacer tuve que montar los originales y mi me borró el fallo
@martinchurch286310 ай бұрын
Cheers Rob I’d appreciate feedback of how much better you think they are 👍
@MrRctintin10 ай бұрын
Thanks Martin. It’s a job to tell, without flying. The collective stick feels super smooth, but it’s going to take time to tell if the cyclic is better.
@BlairEwing7 ай бұрын
Thanks rob
@SteinarWalaker10 ай бұрын
You are best mate nice move 👌😊
@MrRctintin10 ай бұрын
Thanks buddy 👍
@IFLYRCHELICOPTERS8 ай бұрын
Great Vid, just 1 add-on on calibration, collective 0, long press.
@luismartincordero80789 ай бұрын
Me gusta esos gimbal donde los a comprado me puede decir muchas gracias
@brownietaurinski38157 ай бұрын
Turns out it’s a great way to brick your radio!!!!!! NO WAY
@MrRctintin7 ай бұрын
Mine has been fine so far.
@1c1r1x6 ай бұрын
Hi there, so what was your experience with these new gimbals..? Have you noticed any issues at all, or discrepancies..? How would you rate these in comparison with the stock ones.. Thanks
@MrRctintin6 ай бұрын
Hi, I’ve had no issues at all with mine. They feel smoother, but for me I live that I can adjust spring tension and throw length from the front of the Tx. I use a reduced throw pitch stick, have done since my Futaba days around 2009-10 and used to that throw. That’s easily setup from the front.
@chuckbirt92836 ай бұрын
I did the swap on gimbals following your video and my screen does not light up. The touch works just not the back light, any ideas? Is the screen light powered by the red/white wire?
@MrRctintin6 ай бұрын
I don’t now which wires do what, so I’d suggest you carefully go over each plug and check they are all installed fully. Also be absolutely sure the ribbon cables are fully reseated.
@JJ203717 ай бұрын
Why New gimbals? Original not good?
@MrRctintin7 ай бұрын
Originals are fine, new ones a billet aluminium, with Hall effect sensors, so even better than ‘fine’
@JJ203717 ай бұрын
@@MrRctintin thank you
@daverc514 ай бұрын
has your radio bricked yet?
@MrRctintin4 ай бұрын
Nope.
@daverc514 ай бұрын
@@MrRctintin cool, dont ever update the firmware :)
@MrRctintin4 ай бұрын
@@daverc51 yeah, sneaky buggers adding in seek and destroy patches….
@cdmc0125999 күн бұрын
@MrRctintin I've been looking at doing this to my 1st gen Vcontrol. It's completely factory with no updates from the day it was first released. So, I should be good to make the swap. I find it petty for a company that dominates in so many areas to redo their software block radios that has this swap. Of course theirs no proof of it other then the 100s of post I've read.