How To Remove Ford Fuel Line Fittings Without Fancy Tools! Quick Disconnect DIY

This is a video of me replacing the fuel filter on my 1999 Ford Ranger. I was able to make a tool to overcome the quick disconnect fitting couplers out of an old felt pen. This method should work on many Ford vehicles from 1995 - 2012

[@michaelgordon6146]

Simple genius guy! I told my wife, "go ahead and leave, I've got everything I need". Then I got to the freeking fuel line. An old dried up sharpie in my tool box and line off five minutes later! Thanks

[@yourputer]

You didn’t try and wow people with your intellectual prowess, just showed folks how to save some money in a pinch. You not only walked us through it, but also maintained that positive attitude you mentioned in the video! Kudos brother! Thanks again! Lou G. “If you can’t explain something in simple terms, you don’t have a firm grasp of the topic” - Albert Einstein

[@richardrogers2759]

I made my sharpie removal tool just as you described and pushing with a pair of needle nose pliers, instead of regular pliers on the make shift sharpie cap itself, the line easily released. Great idea, and great video. I watched numerous videos of guys trying to use the actual tool you would buy to do it and they were fighting their way through it. One guy even ended up tearing the retainer clip up and it fell out, he’s got bigger problems now. The plastic cap is much gentler on those spring clips, than that metal tool.

[@gregw3518]

Did this today, perfect man changed the filter in under 10 minutes and it was the first time ever. Remember folks pull the fuel pump fuse and start the vehicle or attempt to start to depressureize the lines

[@imericdean]

after fighting this thing for an hour with the "provided tool" .. after watching this the entire job was finished in 5 minutes. thank you very much. worked like a charm.

[@jenniesgarage]

+Eric Dean Great to hear, thanks!

[@sharpshootah8852]

+Jennies Garage I gave a thumb up

[@jjanlisa]

Thank you so much. I live out in the boonies and the nearest parts store is 30 minutes. This little trick did the job. I did have to grunt here and there and lift my left leg up about 6 inches but in 10 minutes I was done. Kid wasn't happy about losing a sharpie but hey, I owe him 15 minutes on his bed time.

[@dan.gpincock3371]

Qq¹¹¹11a

[@curtisbacon8070]

Tried for 30min with "their" quick disconnect tool no luck. Found this video and literally 2 mins later done. Thank you!

[@jomas3050]

Had to go on record. I watched your video and then followed your steps and SUCCESSFULLY replaced my fuel filter. It was not easy at first, and the cap gradually started getting roughed up, but after a few more tries it was golden. This is a hell-yeah video. Awesome job ;)

[@masterkohn1]

Helped a guy that was broke down on the side of the road.Came across this video and it Worked like a charm . ACES

[@joeyosemite6628]

Amazing! I fought and fought with this thing, looked at other videos online where people said they got stuck, then I found your video, went back and tried again, and was successful the first try! Thanks for taking the time and trouble to make this clear, helpful video!

[@swevans141]

Dude!!! You are a life saver. Explorer exploded friday on the way home from work. A full weekend of piano recitals, sporting events and then a medical emergency left me at 11PM still needing to replace the filter. One side came off by itself. The other side... not so much. after an hour of pulling, pushing, banging and prying, I decided to see who else had problems. Found your video and withing 3 minutes I had made the tool and... DAMN!!! Thanks again.

[@cyndicorinne]

Thank you! Whether or not you use the disconnect tool or a sharpie cap, it's so great that you showed what the clips look like and how they work. You clearly know what you're doing and it's great you show others!

[@jeauxbleaux7613]

Awesome tutorial, thank you so much!! In spite of all the dried-out Sharpies we have, I used a tool I had purchased a few months back. I had been postponing this maintenance because I didn't understand the mechanics of the connector. Your video did a wonderful job of showing the clips and their function. I also took your advice, even with the cheap plastic tool, a positive attitude came in handy (perhaps especially because of the cheap plastic tool). Great camera work on your part too!!

[@timmcdonald9645]

Thanks for sharing, you help me remember that there are good people like you still out there in this world.God Bless you and your family and keep you safe through the COVID-19 pandemic .

[@elljones4031]

11 years later, and this video still helps! I'm a 30 minute one way drive to town...saved me a trip. Thanks!

[@dthievin]

If Ford calls this a "quick disconnect", they're full of baloney. It took me two hours -- and that's using the proper tool. If you have the project wide open in front of you, that's one thing. In my case, the filter was behind the frame and obscured by other things. It was murder trying to get those "quick disconnects" to let go.

[@jenniesgarage]

+Gus Wah I'd hate to see what their "standard disconnect" looks like!

[@v125138]

+Gus Wah You are correct. Ford's logic is not always what they say it is.

[@hanskinslo326]

Really a "quick CONNECT" not "quick DISCONNECT!" I couldn't get mine off at all!

[@zerkfiter]

Han Skinslo .I've learned 0ver time to disconnect the lines while the filter is still secured in. Bracket..it's tempting to hold filter in your hand but for some reason it doesn't release..I learned the hard way.

[@hanskinslo326]

henry ford - yeah, I have learned that as well!

[@JaromieShrew]

My fuel filter Came with little plastic "tools" that broke when i tried to use them. Thank the Internet Gods for this Video!!!!

[@PowerUsr451]

That was genius! Thank you for sharing. I was trying to remove the transmission quick disconnect line from the radiator and ran into this problem. Stores were closed and came across your video. Grabbed a Sharpie off my desk. Literally took 5 minutes to construct the tool and remove the line. Thanks!

[@iflyiam]

Absolutely helped, thank you for taking the time to show the inside of the fuel line end piece and explaining what your tool was doing!!! 2000 explorer xlt rides Again!!!

[@jetnick3576]

That was a well done and informative video. Thank you for taking the time. Though I think I'll buy the quick disconnect tool, I really like how you explained and demonstrated precisely how the coupling works and what you are trying to achieve with the tool (store-bought or Sharpie-fabricated). The principle remains unchanged. Well done. Thank you.

[@robertogodoy4626]

Ryan

[@jsnelson2]

Thanks for the video! I love seeing someone figure out how to avoid the "go get this special tool" requirement on so many products. Good clear camera work, too!

[@bartstaton2059]

I miss your videos! even if you guys don't end up making any more things like this are actually super helpful. thank you for ALL the videos you made! This is going to be super helpful!

[@Chris-pj1os]

Thank you so much for posting this. It worked like a champ. I had bought the scissor-type tool made FOR fords, but it didn't work (wouldn't insert far enough into the fitting to release the clip). Your method was fast and easy, and worked like a champ. Pretty good "McGyvering" my friend.

[@th3r0d]

You crafty mo'fo. Thank you. Also, a positive attitude is often misplaced in the garage - good lookin' out!

[@TheMattc999]

cRod Ster no, it's not misplaced. I just leave my positive attitude on a hook outside the door before I step into my garage.

[@kennethfetter9743]

Hell yes I liked it

[@leequipe191]

This video is ageless. Extremely helpful. Thank you for sharing!

[@raywengerd4755]

Thanks so much!!! I used your technique tonight. It saved me a trip to the auto parts store plus the cost of the tool.

[@samsquires5193]

I did exactly what he said to do,and the frame mounted fuel pump came out in 3 seconds!!!I'm keeping that marker cap in my toolbox.Thanks for your video!

[@jdkyzer7616]

This is a great tip and made it very easy. (1993 Ford F150) If everyone who got negative comments stopped posting videos there wouldn't be any more videos. If you don't like the video just move on. Thank you for posting!

[@formula1fan992]

Keep up the good work! Even if you purchase the special tool, you often time have to modify it or it simply doesn't work as intended. I almost always create my own tools and improve them over time.

[@staciefreeman950]

Been a mechanic for almost 20 years I like the idea and the scissor tool is OK and only less than $8 but with some vehicles the tool is too long and have to cut it down to fit good thinking Bones, Parkersburg ,wv

[@b.walker930]

Of all the years of Fords/Mercurys/Lincolns I have replaced fuel filters, I met my match today on a 2010 Ford Crown Victoria. Not knowing there was such a special tool, I took the advice of the great guy here and oi'la! I have a Sharpie fuel filter tool! Thank you very much!!

[@wendykauling5880]

You are a genius! Tried using the little plastic clip the new filter came with. Yeah, that was a joke. Then I found your video and found an old sharpie. I cut the cap and took it to my husband who was under the truck struggling with the filter. He popped my makeshift tool on and the filter came right off! Thank you for saving the day!

[@m4v3ngaming68]

lol you're a life saver with that sharpie cap idea bro! I broke both of the easy to use clips to disconnect the filter from the hose....if you wouldn't have posted this I would have been out there all night trying to get it unclipped....the cap was actually easier than the clips were! Outstanding idea and awesome job bro!

[@jenniesgarage]

Cassidy Sr Loiselle Thanks for the compliment, glad it worked out for you!

[@alexbarcelo7869]

***** . I was like wtf this shit cant be done, when you said HAVE A POSITIVE ATTITUDE haha cracked myself up

[@Sk3pT1kaLVideo]

I always forget to bring my positive attitude..

[@jenniesgarage]

Don't skimp on that, it's the most important part!!

[@r-prizzle2168]

I do too

[@jeffbrown3963]

I have the correct tools and I still hate these fittings! Watching this gave me flashbacks to the last time I did a Sport Trac! Very resourceful video but there is no easy way! Always expect the worst because it's probably going to be a struggle.

[@stanmiles5078]

great explanation on how the connections work, and how to remove them. after watching the video, I made a tool and disconnected both fuel lines from the fuel pump in less than 5 minutes. thank you very much !

[@ButtMasterOO]

excellent idea. replaced old filter on a 1999 f150 4.2 v6. had one sharpie that was bad anyway... cut at 3/4" & worked perfectly, took just a few minutes to replace filter. just have the car running and remove the fuel pump fuse so the car dies and there is no pressure left in the system. also use some needle-nose pliers to help push in the piece easier. thanks so much for the great idea.

[@jenniesgarage]

I'm glad it worked for you, thanks for the comment!

[@underfasten]

Thanks for the tip. This is good for night owls that work on their vehicles in the middle of the night and can't run out to get a specialty tool when everybody is closed.

[@enterBJ40]

Lol!!! I love your description of gearhead worrking late at night in theirs rigs...''night owls''.....

[@lilythomson881]

Yes!!! My husband works at night during these Summer months because it's TOO HOT to work during the day!

[@enterBJ40]

Got it. Is the same here in the Caribbean. Temps are scorching high. I plan to work every weekend in my rig but the heat turn me down even if I work in the shadow. I garante each year is hotter here. Must be the I infamous Global warming

[@bdaileron]

You are the man! Needed to change fuel filter on my Miata and I didn't have the tool (which I THOUGHT I had). Just about to drive to a parts store, I figured I'd watch a video to get the right tool. After watching this vid, I sacrificed a 4 year old Sharpie and changed the filter in minutes! Worked perfectly! Thanks!!

[@markymark3730]

Thank You very much. I was just lying on the ground straining so hard trying to pull the fuel line off the old filter and now I know what to do thanks to your very helpful video.

[@RudyMartinez]

saved me driving an hour each way for a stupid tool. Thank you

[@electronicshelpcare]

Thanks for the great video.

[@anthonybell260]

It worked...thanks for the insight!! KZbin forever!!!

[@OperationRV]

Hello J.G. I really appreciate your video tip on this. I was replacing mine on my police interceptor this morning and realized I needed the disconnect tool. Due to your video, I tried it and it was successful, thanks again.

[@ejoshcoron]

Awesome idea! Thanks also for showing us the inside of the quick connect connection. It helps to see what the inner clips actually looks like.

[@douglasnvideo]

Way cool, thanks a lot! You’re a genius! Take the rest of the day off.

[@The247th]

After removing the fuel filter, I put an empty bottle at the end of the hose that comes from the fuel pump/tank and turn the key to cycle the pump for just a second. You wont believe the dirty fuel that comes out. I've tried it on many cars and its always a bit of dirty fuel that comes out of the tank. Its sort of like flushing your tank I guess.

[@jenniesgarage]

***** good idea, thanks!

[@josephscigliano3414]

You flushed out the tank by blowing some gas out the fuel line that was connected to the filter? Amazing. I would think it would be crazy but a deal?

[@r-prizzle2168]

Nice

[@murphychapman203]

@NZT TZN yes

[@wonnie46403]

I wish I'd read this before I changed filter otherwise I'd have tried this. Next time I guess

[@geoffschneider5760]

Finally, a good video that doesn't take forever to get there and is thorough. Thank you.

[@tedkravos7129]

I tried it and couldn't believe it worked! I had to use a small chisel to force the plastic pen thing into it, but came off after 5 minutes of pulling and using the chisel. It worked on both ends of the fluid filter. Saved me money on a tool.

[@kenclark3953]

This is excellent! But, I managed to do one better just now. I saw this and started looking around for some plastic thing I could destroy to use like the sharpie cap. Couldn't find anything, but then I realized that the new fuel filter came with plastic caps on both ends, and they were about perfect. I cut the narrow end off, drilled the wide end a bit to take off the lip inside it, cut it lengthwise, and it worked great. Saved a trip to the store and the bucks to buy the part, and used things I *had* to throw away anyway. Thanks!

[@jenniesgarage]

You saved the life of a sharpie!

[@ronvalley1973]

you are a clever dude, i went out to the shop, found the fuel filter box, and there were the plastic ends

[@davew8569]

I have a dilemma now, re-use the plastic ends or the old worn out sharpie I need to re-use. Politi-enviro-mechanically correct. lol

[@marmar1102]

This was an amazing video! The sharpie cap worked perfectly. How did you ever come about to think of it?

[@joseselina1990]

Sir I was given some wird plastic clamps to remove mine. And I couldn't use it or it wasn't even for it . but with your help I did it with no issue. And I came back to this video to thank you. This is the firt time I do it and it took 10 min . thank you.

[@markvandamage]

1. This trick works! (Amazon has a tool for $6, but not sure if it works well.) 2. Keep a small bucket handy to catch the gas in the line and filter- it will spill, especially from the filter. 3. I pulled the fuel pump fuse, turned the engine over a few times to relieve the pressure since it's a pressurized system. Not sure if it's necessary, but it took a few seconds just to do it anyway. 4. It will take a bit of effort to pull the fuel lines off: be patient. 5. I used an open-end box wrench to force the cap into the quick connect fitting. 6. THANKS FOR THE VIDEO! SAVED ME SOME BEER MONEY!!

[@RK-je9nc]

"quick connect" but takes much longer than undoing a hose clamp.

[@thealliedspy4170]

Exactly, why can't they make stuff simple?

[@joe4171]

Ren K with the $3 tool they actually are faster than a hose clamp

[@fuckjoebiden4976]

Because they have to pay the idiot behind the computer screen that doesn't have a clue on how the filter works to begin with anyway 500k/year, so they can justify hiring him.

[@UnknownDevices91]

Joe Nault Bahahahaha Bullshit.

[@adcraziness1501]

quick connect not quick disconnect! Faster when the car's on an assembly line. They werent worried about the guy working on it!

[@h.m.sdasilveira5710]

Thanks for the "sharp top tip". Whoever said the Pen was mightier then the sword was right. Quick Q. Where did you get your Bench top Vise? It looks massive!

[@TheAtheistWarrior]

Other people attempting to video their 'How To' video's should take note of this persons multiple camera angles and cuts. You can't properly demonstrate every aspect of your demonstration without re-positioning the camera. Great video. Great production effort! A+

[@jenniesgarage]

+Kenny Nipp Thanks for the comment, I'm glad you enjoyed the video.

[@jeff3741]

This worked great for me. I didn't bother with the hacksaw. I just used the wire cutters for all the cuts. $8 Fram filter from Walmart, a pen cap and 2 minutes. Thanks!

[@Duke_Togo_G13]

I just fuckin did this! THE CAP TRICK WORKS FLAWLESSLY! Thank you for this trick! Pure genius!

[@gregbrooks9546]

Now I know why I have owned Toyota trucks for the last 30 years. Easy to work on. The Ford Engineer's need to be strung up by their balls and then made to try to unhook one of these in zero degree whether in their underwear. I tried the sharpie trick and it worked for the end of the filter towards the front but after I unhook the end with the arrow facing the front I have went thru 3 sharpie caps and finally gave up after an hour of cussing.

[@mickblock]

Quick connect. Not quick disconnect. Also that's a darn good idea. Thanks for sharing.

[@jenniesgarage]

Michael Block Yeah you're right on that one. Slow, confusing, tedious disconnect.

[@thomashilfer1343]

Absolute genius tool hack. Years ago, I bought one of those fancy panty pressure relief kits that didn't work well as I got pressurized gas sprayed in my eyes. I had turned my head to the side. and once I regained my vision I spotted a recently used condom about 6 inches from my face. I was so terrified that I my forehead against the the underbody of my 88 Oldsmobile. On a positive note I must say that the flow of blood into my eyes washed away the sting of gasoline nicely. Anyhow, I'm way off topic, but I shall try your sharpie cap trick this weekend (this time using a fancy car lift in a condom-free environment) on my 94 Ranger and will promptly report back to you with the results. Have a nice day.

[@narutogokumode]

worked like a charm on my 04 Corolla! I'm working at night and couldn't go out to get the right tool but this worked as a quick substitute! thanks again.

[@scottdavenport2967]

I used the tool. $5 for a whole set lol. had the job done and watched half a hockey game before you even measured lmao.

[@randythompson2151]

Exactly 😆

[@ladyoftruth6651]

Ok, I am 65 year old lady out 70 miles from town. Was told the codes that I need fuel filter. Purchased the filter before I left town. Did not get a special tool to release fuel lines. I Did what you said and it totally worked. Bless you! That is kind of stuff people need to know.

[@mattarmstrong1562]

🤣

[@TheScannerz]

The new filter has caps on it that can be cut instead of the Sharpie.

[@billlewey6573]

I tried this at the fuel pump and it worked for the small grey line but was too fragile for the large blue line. Getting the tool. Thanks for the video telling us how this works!

[@laytonvires2953]

the great thing about this video is you can see clearly every move to make to get it disconnected. great job

[@johnkean1196]

Actually you will use that tool every 15k miles when you replace that filter.

[@ProfessionalDad]

Who changes their fuel filter every 15k??

[@johnkean1196]

An ounce of prevention is better than a pound of cure they say, if you change your fuel filter every 15k you will help prevent any future filter issues. Many well respected aftermarket oem suppliers recommend 15k as well. www.airtexproducts.com/news-blog-the-importance-of-a-fuel-filter-and-how-it-can-influence-your-fuel-pump.aspx

[@lpburke86]

Everyone who actually gives a damn about their engine

[@carterstillwell3001]

Liam Burke k

[@darkfireBikes]

John Kean ford says every 75k in my book. you're wrong

[@geargriden19]

Funny these folks commenting to just buy the part it's cheap and less time consuming. I think they are jealous of this trick, parts salesmen or just one of those people who assume you live close to a parts store. Even if the parts store is 2 blocks over its quicker to make this tool than to go there and cheaper! Anyhow i'm off to the parts store for a Ford Taurus. Have a good'nnn

[@jenniesgarage]

thanks! hope you get your taurus fixed up

[@geargriden19]

Decided to take it to the shop this upcoming week and let them figure it out, then go from there on fixing it. Have a good'nnn

[@bluespig1]

Crikey mate. Where's all the anger coming from? I hope you don't have children.

[@charlesrohrer667]

This disconnect tool is 6 dollars, that Sharpie was about 1.50 And he can't usr the sharpie anymore.

[@bobspurloc]

actually harbor freight sells a set of multiple sized plastic quick disconnects for $5 -25% their bimonthly coupons so less than $4 . the sharpie isn't worth destroying to save $2 and waste all that time.

[@Cutlerup]

Thanks for the help! The hardest part was finding a sharpie. Worked perfectly. I went with the blue sharpie!

[@10ring]

Great video! For my 1999 Kia Sportage, I did the same thing, except instead of a pen cap, I used the front half of a 9mm case, with a cut so it could slip around the fuel line.

[@gotrocksinhead]

Thanks a bunch. Your clever idea saved me a couple bucks and a lot of time driving into town to get one stupid tool. I appreciate the tip. Oh, yeah... ignore the trolls :)

[@tamisands2548]

gotrocksinhead ii

[@thomasl7917]

left video playing while I went to store got the tool. came back home and changed filter before ended.

[@alki9859]

😅😅😅

[@Virgil7long]

Second time changing mine on 1995 F150, it’s located in between the frame and tank and it about took me 2 hrs trying to remove the fuel filter. The worst is removing the filter that’s spring caged. Fram came with removal tool it worked. I believe this was causing the vehicle two have start cranking problem. Mine my have clogged, it was black on the tank side of filter. Great video.

[@gc3022]

THANKS MAN, after 3 homemade different ones, and buying the universal tool that didn't fit, Pen cap is the WINNER...

[@pgpete]

Sharpies are just as expensive as the specialty tool where i live!

[@fdkisselsteinjr9939]

Yeah no shit

[@yankeeprepper.3393]

Maybe his Sharpe was all dried out.

[@thomashilfer1343]

Sharpies are free from the office. Nyah ha haaa!

[@dkhill27]

Damn wasted my last good Sharpie when I went to put it over the line it shattered causing me to start cussing. Busted my knuckle and sprayed blood all over. Cussed some more and kicked the neighbors cat for shitting in my driveway. Then cussed the neighbor out. Today was not a good day

[@hansoncrack]

Thank You!!! 2000 4.2 v6 E-150 econoline which uses the 5/16 fuel line. I had watched this video and borrowed the tools for the fuel line release from the local hardware store. The removal tools were to big for the clearance on my fuel filter by a 1/4 inch. Sawed down a sharpie and with a "positive mental attitude" got the filter replaced!

[@terrymeals6098]

Remember to release fuel pressure before removing filter! Will have to watch a video on relieving pressure, was waiting on you to elaborate on that. Thanks for the video

[@robertoortiz85]

tool is like 6bucks in harbor Freight

[@jenniesgarage]

haha yeah harbor freight just be careful to double-bag and bubble wrap it so it doesn't break on the way home :P

[@dyvrsI]

***** Not to mention the gas you burn goin there and back. My local store isn't just around the corner. Saved me a trip for sure ha. Thanks!

[@jijzer4581]

***** 8 usd for a feul filter is NOT expensive ok i am mostly paying 20 usd

[@murphychapman6157]

roberto ortiz

[@murphychapman6157]

roberto ortiz I guess everyone don't have a harbor freight in their backyard like you do idiot!!!

[@gothicasshole]

8.74 pricy?? Your lucky for my s10 cost me 43 dollars!!!!! And no don't go hating on gm plenty of gm cars have less expensive ones but mine has a return line so bc of a new hole and fitting they jack it way way way up so your lucky

[@MyoMyourin]

he was obviously joking

[@petergoat66]

Great, very informative and well done video; thanks for showing the interior of the fuel line quick disconnect fitting- it really helps to know exactly what one is dealing with up front and not working blind so to speak.

[@SuperChriscunningham]

I tried his method and it was very difficult using the end cap of a sharpie. Very tight not much room. I drove to Oreilys auto parts and for a few bucks found the the plastic tool to remove it. it was well worth buying the tool, it came right off.

[@khvnp1l0t]

While I value thriftiness and clever thinking, I wouldn't do this to my truck. A sharpie cap is a bit thicker than a scissor-type disconnect tool, you don't know if repeated use will bend the retaining clips back too far due to the thicker sharpie cap. If that happens, you're out a fuel line. Seriously, the cheapo 4.99 harbor freight tool is fine for someone doing their own maintenance and much easier than the wrestling you did with that thing. And you will be using it far more than "once in your life", I see estimates of fuel filter changes ranging from 30k to 70k miles on the ford ranger. Being thrifty means saving money doing this yourself, but also investing in the proper equipment to keep your car running as long as possible. Get the right tool and do the job right. Don't spread potentially harmful information.

[@aux1z11]

I watched this video a few weeks ago and cut my sharpy up and used it on my fuel lines on my ford ranger and it was a pain in the ass plus it bent all my tabs but I took my pick hook and got them back the way they was, after that I bought a 27 piece set made of aluminum in a case for 22.95 and works much better.

[@yankeeprepper.3393]

You do it your way and he can do it his way. Good video.

[@wheelingndealinglife8656]

I upped you. I used a old condom, filled it with gas and wrapped it around clamp, lit it on fire, and ran like hell. When fire dept. left fuel filter was removed but downside is truck needs a little more work now... and currently walking to work. Maybe should have sacrificed a sharpie looking back...

[@SupraSav]

Thank you for this video. That slight struggle with disconnecting the clips for the fuel line has me hesitating to really mess with it. Knowing my luck I will break something and I'll be SOL.

[@familypell5956]

Thank You for taking the time. I really appreciate your time and effort

[@upyoursassmonkey]

That's a lot of trouble considering that you could buy the tool while you're at the auto parts store getting the fuel filter. They are like $6 and you don't have to dig around for a sharpie.

[@jenniesgarage]

Hi! To each his own, but It's not "a lot of trouble for me". I don't like spending money if I don't have to, whether its $6 or $60000. Plus I get much more than $6 worth of satisfaction knowing that I made something myself to do the job :)

[@markgildersleeve9319]

Hey DeadCat - if you consider cutting the end of a Sharpie cap off "a lot of trouble" perhaps you shouldn't be working on your vehicle in the first place. Although I am very mechanically savvy and have most any tool I might ever need in my shop, I didn't realize I needed a special tool until I had returned from the parts store, had the truck up on the jack and the fuel pressure relieved. So - undoing that, plus the mileage cost for driving 8 miles round trip to the auto parts store and back plus the cost of my time to drive there and back plus the cost of the tool... I would say that cutting off a sharpie cap is a BRILLIANT alternative solution. If you have 2 ounces of mechanical ability, cutting the Sharpie cap and splitting the edge should take you about 2 minutes. That's if you're blindfolded. JG, thanks for the tip and my sympathy goes out to you for the ignorant thankless morons that always know better. Peace.

[@upyoursassmonkey]

Mark Gildersleeve Lol, you weren't even bright enough to check and see what special tools were required for the job before you started, and you are going to try to tell someone else "perhaps you shouldn't be working on your vehicle in the first place" whatever you say buddy. Obviously you don't do much work on cars if you thought you "have most any tool I might ever need" since the quick disconnect is used all over modern vehicles. Of course the most laughable part of your comment is where you mentioned having the fuel pressure relieved as one of the reasons you didn't want to stop and go get the tool from the store, if relieving fuel pressure is a big deal for you, you're obviously doing it wrong.

[@markgildersleeve9319]

DeadCats You're right. You are obviously so much better, smarter and more successful than everyone else here. You certainly have the right to critique everything that everyone on the planet does because you are perfect. I wish I was more like you.

[@markgildersleeve9319]

and by the way - if you are so knowledgeable about vehicle repair, why were you watching this video in the first place? You know everything.

[@CheeseyGutterBall]

you are a fucking genius

[@jenniesgarage]

haha no, I just didn't want to drive to town and spend $5

[@lizcappello3895]

Jerry Pratt codep1395

[@philliphoefler6663]

My filter came with the cheap little plastic tools. your video is obsolete.

[@millionairesclubllc3193]

Phillip Hoefler oem motor craft fuel filter I bought today from advance didn't come with no tool so you're mistakenly wrong . Every filter is different newbie

[@ctjohndeere]

GREAT! Someone always comes up with a better mousetrap. Positive attitude is always a plus. Fuel release pressure is a must ruined a pair of $300.00 lenses

[@TCWRHF]

Life saver! Thank you for sharing this trick! I bought the tools that were supposed to work and didn’t.

[@jimjackle2739]

the cost of a sharpie is more than a plastic disconnect tool. These tools are cheap as dirt

[@metro3692]

Not as cheap as this guy.

[@gymhourfee]

$38 dollars for the tool where i live then tax. That's one expensive sharpy!

[@corywelsh269]

I have a "how to" video with detailed instructions on nail clipping. You should check it out.

[@jenniesgarage]

Cory Welsh thanks for that valuable pointer on personal grooming. lets get all the mechanics lined up for a manicure & eyebrow wax.

[@purestress2]

Jennies Garage LMAO

[@vertigo6982]

men who work with their hands prefer long nails because they're basic tools for prying and digging. Notice I said "men" because men don't worry about what they or their hands look like. You must be one of them girly boys out west.

[@TakeItEasyC6]

I used this method on my 2001 Mazda Miata "NB." Worked great! Couldn't get it with a 4-way metal tool from the parts shop, but a Sharpie cap did the job.

[@wonnie46403]

I can't believe this worked really well. Thx for the tip. I finally changed fuel filter with your marker top tip

[@patrickhurley707]

For $5 you can buy a 3/8" disconnect plastic tool. It took me 1 minute to disconnect it while you struggled.

[@purestress2]

Patrick Hurley took me 10 seconds while you struggled for a minute. Arggg Hulk Smash!

[@skystormfishing]

HA AH you were DUMB enough to spend $5 and now have $5 less than everyone else who was smart enough to do this! BUHAHAHA

[@lucasmccann1]

Nails are so long

[@dingo0408]

Appreciate the video - Saved me a ton of time & frustration. I have a prized "89 Ford Crown Vic and needed to replace a leaking transmission cooler quick connector @ the radiator. The line size is 5/16" and I was not able to locate the proper sized tool, without special order & mucho $$. So, using your ingenious idea, I found a BIC Brite Liner in my junk drawer, cut the closed end off the cap, sawed a slit the length of the cap, left the pocket clip in placed for better leverage - Voila - a perfect fit & instant disconnect. One plus on the cap - the open end is factory beveled, so made it a snap to insert in fitting. The cap is going in my tool box. Thanks J.G.

[@jenniesgarage]

Thanks for the comment, it's good to know that this type of connector is used on other connections besides the fuel filter, and there are other pens in the office stash that work to release them.

[@lbcsv]

“...positive attitude.” 🤣😂😂 Seriously, thanks for showing the inside of the connector. No one else did and seeing the tabs, helped.

[@Fldavestone]

Oh my God people just go get the tool sheesh,save yourself the trouble.

[@JohnKoessler]

I can't believe he wasted a Sharpie!

[@upndnglo]

David Cleaves so simple to make, especially if stores are 10 miles away and you're already working on the car!

[@ny1t]

Some people have never read the Blind Men and the Elephant. They only know the world from their own pespective.

[@TheEldest928]

With the money you saved on the tool maybe you could buy a finger nail clipper. Disgusting...with those hairy arms it looked like Wolfman was working on that car.

[@SemperFi85to91]

A grown man is actually gonna take the time to comment that another man's fingernails are disgusting. SMH. How's your nail salon doing?

[@joshuarobinson1397]

Love the whole "positive attitude" remark... Great work bud. Ill be using this today!

[@techman1274]

Thanks I only have one car & I was stuck not knowing how to remove the Lines from my 1998 mountaineer and no ride to by the tool & you Sir saved my tail end and I was able to get the wife off to work on time. I will buy the tool but that sharpie idea was awesome! I used to be a A/C tech I had all the A/C line release tools for every size but that one because they don't make A/C lines that small with quick release. I wanted to say thank you so much for the idea that saved my BUTT! lol

[@grewil3]

Thank you for sharing this great idea, sir! I don't have that tool, and was wondering what to do, and now I know.