07376369067 www.williamsmobileclutch.co.uk Support the Channel Donate: www.paypal.com/donate?hosted_...
Пікірлер: 139
@nhatdoesit75703 жыл бұрын
you made it look so easy! bouta do my first clutch replacement on my e46 323i. thanks alot man
@WMCS3 жыл бұрын
Hope it all goes well. Remember safety always. Have a spotter close by for an extra pair of hands if needs be.
@silviosdse14 жыл бұрын
great work kevin, i'm from brazil and i love to wacht your videos, your skills about change clucht is incredible.
@danmarcu25054 жыл бұрын
Nice alignment for clutch with 2 pins, good job
@WMCS4 жыл бұрын
Dan they were actually 2.5mm Allen keys. Does the trick 100% every time.
@greenmarcus44444 жыл бұрын
Clutch master 😅 good job bro, as usual 👍
@nitroheal59033 жыл бұрын
respect.. I did it with my friend on e46 m57 hard work and you do it solo. hard part is with transmition heavy shit. good job really like it
@christiankayal4 жыл бұрын
Omg.. Very good.. Your a clutch warrior..
@JustAnOrdinarySimmer4 жыл бұрын
The clutch warrior beasting it again as usual! tonnes of respect for you!
@zamsystemdevonmiles.12913 жыл бұрын
Good mechanic UK and good service.
@gregdelasavoie21054 жыл бұрын
Thanks you mate for this vidéo....it's not easy to you to take good angle of view but you are arrive...👍👍👍 Sorry for my english....
@drexxore4 жыл бұрын
Awesome video as always dude!
@user-cs6us5px1s4 жыл бұрын
perfect job again
@Markstevos4 жыл бұрын
Another good job well done mate. 👍
@marcs59604 жыл бұрын
Love the new car jack
@WMCS4 жыл бұрын
Hi Marc..,, I’ve had the jack for a while now ..,, but it comes only usually when I’m doing RWD for easy access to the underside of the vehicle..,,, Really appreciate the time you’ve taken to leave a review on our forum
@supertirk4 жыл бұрын
It seemed easy from this living room 😎
@bmwm5bmw6103 жыл бұрын
Omg that gearbox very heavy for one person to lift up or put it down good job Kevin 👍
@WMCS3 жыл бұрын
They are a little bit in the heavy side.
@maxautouk4 жыл бұрын
I did a starter motor on a Mercedes a150 and I think it probably took as long as this clutch job 😂 subframe down.... Remove loads of gubbins..... Too hot for it! Nice to see you still hard at work, we are lucky really people always need their cars and need mechanics
@WMCS4 жыл бұрын
Hey Max..,, nice to hear from you. The saga of the A class ..,, honestly they are such a tight squeeze they are ..,, sometimes it’s best to drop the whole engine down. Fair play to you to take it on in a mobile capacity..., Still at it everyday.., you’re right the heat really slaps us out here 🤪...
@maxautouk4 жыл бұрын
@@WMCS I had the starter on that a-Class...then some module diagnostics on a dacia that had been crashed and won't start... Then to top it all off I get to my last job to do a shaft, drop links and front brakes and as I get there the owner said he'd lost the locking wheel nut and didn't mind if I 'just ripped them off'............... I'm home now and glad to be in the shade!
@WMCS4 жыл бұрын
Max Attack 😂😂😂😂💪💪..., that is a proper day that ..,, is your lady pampering you now ..😆🤩
@cosyclown42544 жыл бұрын
Soldier brvha Hope you are well and staying safe Great video Kevin 👌
@maxthecaddy84514 жыл бұрын
amazing work for one man to do, and heavy to lift on your own 👍👌
@WMCS4 жыл бұрын
Max that 3.0L gearbox was heck of a lift .., the video didn’t do it justice in terms of it’s size ..,,
@maxthecaddy84514 жыл бұрын
@@WMCS i no buddy massive job on your own i bet you didn't look forward when that one came up on your list😡
@WMCS4 жыл бұрын
maxthecaddy it was done yesterday and the heat really spiced things up under there😂😂..,, it’s all good tho. I love it really.., 🤩
@bobbobby57244 жыл бұрын
Fantastic fantastic video
@denissetruquini73054 жыл бұрын
Very good job man ai ting You are very stong thankyou very much
@danthecarman84404 жыл бұрын
Hi Kevin, great video as always. I look forward to your videos. I would of liked to of seen exactly where you poked them Allen keys in when aligning that center plate, but you got to keep a few tricks of the trade to yourself haha.
@WMCS4 жыл бұрын
It works every time them two Allen keys. They are 2.5mm..,, thanks always for the support. Very much appreciated.
@teodormihai89053 жыл бұрын
@@WMCS Can you let me the link with the special tool alignment clutch for my bmw e90 330D 2007 ? Because idk how to use this two allens like you did. Would be great ! Thanks a lot ! You did a great job Albert ! Hope you have a good day !
@teodormihai22442 жыл бұрын
@@WMCS would you Show US how to use the clutch bonding glue ? I ve seen you tellin this on latest Video bmw f10.
@aarjordan4 жыл бұрын
Hello Kevin’s got a new toy
@pedroluisvelaarranz33163 жыл бұрын
Que grandisimo MECANICO!!!!
@user-zf9kv8wi8v4 жыл бұрын
i love your Job 🇩🇿
@tomdavies3780 Жыл бұрын
Great video! Is it ok to re-use pressure plate and bell housing bolts on this car?
@edgarsoto8860 Жыл бұрын
What a total badass ! Made that look easy what is it you did there with the clutch when you popped the little center piece out
@nordineb146111 ай бұрын
Good job
@duboispascal11724 жыл бұрын
Bravo👍
@sorrymate41894 жыл бұрын
awesome!
@aidsy604 жыл бұрын
Thanks again for a fantastic video, love the scissor lift too btw.
@Boymentation19944 жыл бұрын
Great video as always! How long did this one take you
@mcqcjc84094 жыл бұрын
What do u think of that lift? Is it better than jacks?
@user-ox4eu3xi3s4 жыл бұрын
that box looks heavy, do you ever use one of the jack - gearbox mounts for a trolley jack? surely some boxes are just to heavy depending on the car / van to be lifting on your own, at least you can go home knowing youve earned your money!
@isitgoodtodo28343 жыл бұрын
did it acutally take 45 min? or longer because of editing trying to tackle this job myself
@j.j20294 жыл бұрын
Top 👍
@unbehagen434 жыл бұрын
respect
@stoiancostel51474 жыл бұрын
Hola amigos me gusta tu video un saludo de madrid,,
@WMCS4 жыл бұрын
Saludo amigos. ✨✨🤩
@teodormihai89053 жыл бұрын
Can you let me the link with the special tool alignment clutch for my bmw e90 330D 2007 ? Because idk how to use this two which you did. Would be great ! Thanks a lot ! You did a great job Albert ! Hope you have a good day !
@WMCS3 жыл бұрын
It’s two 1.5mm Allen keys.
@pussinboots11454 жыл бұрын
Why red grease as opposed to any other?
@e.mvehiclesolutions54603 жыл бұрын
Hey MR CLUTCH great videos as usual What grease are you using?? And where can I buy the quick jack from. Thanks in advance keep up the good show 👍
@WMCS3 жыл бұрын
Hey 👋.., it’s red rubber grease and quick jack can be bought off eBay now.
@iantumulty4053 Жыл бұрын
Cheers 🍻
@madformodz7252 Жыл бұрын
Great video wers the best place to buy cluck kit myn is rattling like mad
@WMCS Жыл бұрын
Euros
@westawesta90634 жыл бұрын
Yoooooooo Kevin 👍👍👍👍👍👍
@danmcnelly59013 жыл бұрын
Hi Is this the same procedure on an bmw e46 330d? I.e. can you do it without removing exhaust or prop shaft bearing Also do you need to support engine when removing gearbox? You make it look so easy👍
@WMCS3 жыл бұрын
Hi Dan. There’s multiple repair vids for BMW. I think there’s a specific one for your one.
@danmcnelly59013 жыл бұрын
I found two videos of you doing 2007 330d If you ever do a 2003-2006 e46 330d it would be great if you make a video 👍 Thanks
@GeorgeAusters8 ай бұрын
Someone definitely not replaced that flywheel when they last did the clutch.. Clutch had plenty of life left in it!
@WMCS8 ай бұрын
Happens a lot. Then a few months to a year the whole thing needs to be redone again. A but if false economy not having it all done first time.
@zaydounezz48883 жыл бұрын
Good job you are not supposed to bleed the air in the circuit at the end? Cheers
@WMCS3 жыл бұрын
It’s a sealed unit so not really necessary
@tonyc28374 жыл бұрын
That is damned hard work . How many do you do a week on average.
@mcqcjc84094 жыл бұрын
I bet he does in between 10-20 a week looking how fast he goes through
@mattchater55052 жыл бұрын
How did you align the clutch using the Allen keys? What holes did you put them in?
@drm48574 ай бұрын
Anyone have a photo or diagram of where you inset the allen keys? Cant make it out in the video!
@haythemgharsallaoui3 жыл бұрын
when to know when to change the clutch kit ? i bought a Mercedes Class C 2013 with 160 000 km thanks in advance
@WMCS3 жыл бұрын
When it’s starts slipping or when the gear feels hard to engage ..,
@williammcgowan66874 жыл бұрын
what is the rate for supply and fit clutch for ford mondeomk4 2ltretdci 6speed 2009 140bhp thanks
@WMCS4 жыл бұрын
Text me the registration and I’ll put a price together for you 07376369067
@Mority072 жыл бұрын
I was thinking it is impossible to replace the clutch without remove the exaust
@mcqcjc84094 жыл бұрын
Again red rubber grease not good for that at all. Red rubber grease is made for seal protection - it is compatible with brake fluid seals but it is a simple vegetable grease Its temperature range is not adequate for clutch and its anti seizing properties are not that good at all as it cooks of at higher temps. U can get a 500g ceramic grease can for 15 quid and u can use it on any friction points - it melts at 1000 degrees and does not get thin when under high temperature making it to be pushed out
@marlonhofmann77363 жыл бұрын
Where does the wiggle come from ? The clutch or the two mass wheel 😅
@WMCS3 жыл бұрын
The double mass flywheel
@slitherdurant Жыл бұрын
Bro just dropped the trans on him self I’m over here acting all scary with a jack. Good shit 🫡
@WMCS Жыл бұрын
Thanks for the feedback mate. .. much appreciated
@DonMikson3 жыл бұрын
Hi. Do you know if in version 2.0d engine m47n2 is exactly the same way or are some difference ? Regards from Poland
@WMCS3 жыл бұрын
It’s a lot easier than this. More room. But same layout.
@swms96794 жыл бұрын
Another great vid, how long have you had the Milwaukee for ? It looks pretty beaten up haha
@WMCS4 жыл бұрын
Thank you John..,, I can’t remember the exactly but it’s passed the two year mark. It does take quite a bit of bearing to be fair that Milwaukee.., but it’s a really good impact.
@swms96794 жыл бұрын
Kevin-Albert Williams i got the same one as well and yes it does wonders 👍🏻
@WMCS4 жыл бұрын
John J I rely on it that much that I keep a spare one of the same ..,, it’s honestly one of the better impact wrench I’ve owned...,, are you a full time mechanic then.
@swms96794 жыл бұрын
Kevin-Albert Williams i can see that it is your main tool haha , no im not a mechanic, i just do work on my car when theres a need and help out friends and family .
@mcqcjc84094 жыл бұрын
@@swms9679 He asked if u r full time mechanic. How can u say u r not mechanic when u said u fix your cars and family cars? Makes no sense to underestimate your skills. U should have said u have no clue at all - in the end u havent finished any mechanic school or trade course. So for that fact even if u can make a cylinder bore milling u are not mechanic because u have no papers for that
@nathancannon96833 жыл бұрын
How much do you charge I have a 55 320d and the flywheel has just started to rattle
@WMCS3 жыл бұрын
Hi Nathan. send over your details via. www.williamsmobileclutch.co.uk
@dzk67143 ай бұрын
Im planning to do it on my 330xd , does being xdrive make it harder or is it the same ?
@WMCS3 ай бұрын
It’ll be a bit harder due to the transfer box.
@noelkelly76804 жыл бұрын
Nice lift is this a new one higher or same one in another vid
@noelkelly76804 жыл бұрын
Another good job as usual
@WMCS4 жыл бұрын
It’s the same lift .., I’ve changed the rubber blocks to bigger ones.., it gives an extra two inches. ..,, but makes the difference.
@Megalocade4 жыл бұрын
You can't beat a Longitudinal engine, so much easier to work on when it comes to clutch time, just done a mates mitsy shogun we managed to slip the box back using the box support beems below just enough space to get the flywheel out and the rest of the job done. Nice lift, a lot better than those mobile scissor lifts, certainly looks sturdy enough, you alt to invest in a low lift transmission jack mate best bit of kit I ever purchased especially with the twin tilt to get alignment right, bench pressing tranys if fine when your young but at my age it ain't happening.
@WMCS4 жыл бұрын
Shin Gouki in-line engine all day long. Agree with you 100%... that’s all you need really. Just enough access to drop clutch and flywheel.., I’m gonna be doing a transporter next week. Just enough room to get a breaker bar in there ..., how old are you to still be tackling them repairs then. A shogun .., with the transfer case attached..,, I’ve stopped doing them. Too heavy.
@Megalocade4 жыл бұрын
@@WMCS 51 chap, I don't do this for a living now, I don't mind for close family and friends, much prefer the restoration side of it, doing up classics.
@americandream12642 жыл бұрын
Hello Kevin! I watched your's videos on youtube on how to replace the clutch on a BMW and I followed them step by step Kevin. After 7 hours, I finished putting the parts in the car together . First I started the car, and then I hit the clutch pedal to put it in the 1st gear but the stick can not move. I could not put the stick on the 1st gear or in the reverse. I do not know why. I am so worried. My clutch kit is new. Does anyone know why I can not put the stick in the first gear or in the reverse to move the car? Wanna know. Thanks for your time, everyone.
@Depytat964 жыл бұрын
22:16 What is the name of the red grease?
@swms96794 жыл бұрын
Дмитрий Фонинов red rubber grease
@adriandukes76904 жыл бұрын
Wow love the lift, I bet it saves some time jacking the vehicle up, was it a costly investment
@WMCS4 жыл бұрын
It cost me about £1300..,, I only use it for RWD ..,, as all wheels needs to be up in the air to be able to move freely under the vehicle ..,,
@adriandukes76904 жыл бұрын
Kevin-Albert Williams end of the day if it saves you time it makes you money
@WMCS4 жыл бұрын
Adrian Dukes definitely saves a lot of time ..,, plus it’s quite sturdy. Only thing is needs to be on a very flat and level surface.
@Videostop2023pt Жыл бұрын
Good friend I have a bmw and my big problem is to put it in the air with only one or two jacks and easels ... do you have any method due to your experience? if i had this monkey it would be easier but they are still expensive...thanks if you can help
@WMCS Жыл бұрын
I personally wouldn’t put myself under all wheels up only on axle stands… it can be quite detrimental
@Videostop2023pt Жыл бұрын
@@WMCS yes friend but to change the gearbox oil of a bmw 320 2017 what do you advise, this of course to be done at home
@Tom-ol6cu Жыл бұрын
@@Videostop2023pt use axle stands but leave a jack under rear subframe just for extra measure.
@philrussell98272 жыл бұрын
I can't get the bolts out on the top side of the gearbox??? Any suggestions
@WMCS2 жыл бұрын
Pry bar. Have you undone the 10mm bolt behind the gearbox for the plate.
@philrussell98272 жыл бұрын
Mate the last 2 bolt (one for the starter and then the last M16 top bolt) I can't get my hands in there i have tried going in with extensions from the back aswell
@WMCS2 жыл бұрын
A bit tricky they are but you can get it.
@lcka813 жыл бұрын
If you change a BMW clutch, you have to replace the ball pin in the gearbox too, part number 21511223328. Otherwise the clutch won't work properly, regards Simon
@WMCS3 жыл бұрын
Thanks for that little bit of info Simon. Much appreciated.,, Regards. Kevin-Albert
@sls1273 жыл бұрын
Spartiate!
@madformodz7252 Жыл бұрын
Are you mobile ? How to to change cluch in 330d 2006 auto im based Lincolnshire? Thank you 😊
@WMCS Жыл бұрын
www.williamsmobileclutch.co.uk
@johnp66364 жыл бұрын
What’s the hardest clutch you have ever done?
@WMCS4 жыл бұрын
For me personally it was an Audi A8..., it’s a great car but a bit of a squeeze getting to certain bell housing bolts.
@johnp66364 жыл бұрын
Kevin-Albert Williams don’t know how you do it all on the floor I once did a 2012 Toyota hilux 4x4 clutch on the floor never again. keep up the good work 👍👍
@WMCS4 жыл бұрын
Paul P oufff a 4x4 hilux that’s one heck of a gearbox and transfer box I’d imagine. ..,, put you off did it ..? ✨😆
@johnp66364 жыл бұрын
Kevin-Albert Williams yep no more 4x4 gearboxes on the floor took me and 2 other mates to lift it in and out that was one big lump 🤣
@cristianojoana18984 жыл бұрын
I once did a hilux 2013 4x4 d4d 144cv but didnt take it ou just twisted it to left and pull it back enough to change the clutch.. it rested in the support bracket that are betweeen frames its very heavy..
@DonMikson3 жыл бұрын
26:05 you are crazy :) how much does it weight ?
@WMCS3 жыл бұрын
A little bit 🍻
@zaydounezz48883 жыл бұрын
What is the name of the part you have in hand at 38:53? Thanks
@WMCS3 жыл бұрын
It’s just a bush that sits between the cradle and the gearbox.
@zaydounezz48883 жыл бұрын
@@WMCS is it known as "gearbox silentblock "?
@ivandrago12674 жыл бұрын
i look that you have a lift now and dont look your van ...So are you working at home ?
@ivandrago12674 жыл бұрын
Sorry .. i see your van at the end of work ! So you build the lift every time ?
@Josh.Sanderson Жыл бұрын
I did this job and it took 24 hours 😂 video on my channel criticise my technique haha
@WMCS Жыл бұрын
Send us a link to your channel and we’ll give it a thumbs up 🍻🍻
@Josh.Sanderson Жыл бұрын
@@WMCS Damn thank you man! ❤️🍻 hopefully you’d find it entertaining!!! kzbin.info/www/bejne/q5OTdpVsl9Oej5o
@Linged Жыл бұрын
Im doing this clutch today and got no clue how to remove top bolts 🤬🤬🤬
@WMCS Жыл бұрын
You need 1/2 drive extensions and feed it all the way back to prop shaft and undo it from there.
@WizzRacing2 жыл бұрын
I bet this guy has abdominal muscles made of stone..Lifting the Gear boxes all week long.. No need to go too any Gym to workout...