Made with Film Maker play.google.co... music by audionautix.com
Пікірлер: 33
@boitumeloepheciamaraba374711 ай бұрын
You did not remove the bungy cord you used to hang the caliper. Excellent video...I love the way you do it
@jdurango6 ай бұрын
Excellent job, the only thing that i would do extra is clean the pieces that are rusty, it is very excessive. Thank you
@rowenramnath2016Ай бұрын
Do I need to put new disks. My is still fine?
@toztak3131Ай бұрын
O.K. - i like it . And at the end of the work CHECK LEVEL of the BRAKE FLUID .
@JasonMcguire-t9e Жыл бұрын
You get that bungee cord you used for the caliper?
@alfonsoamores1287Ай бұрын
Hola buen video desde España, se le puede echar a los pines la misma pasta de aluminio, ( en mi caso de cobre ), por ni encontrar la grasa especial frenos? Gracias 🫂
@electrofiction.22 күн бұрын
Use silicone paste on guide pins. Copper grease is based on mineral oil and slowly eats away at the rubber boots, causing them to fail prematurely.
@bigskrilla81647 ай бұрын
is this the same process for the kia K5 ?
@maoinc132 ай бұрын
Why is there Christmas 🎄🎁 song playing in this video 😊 ???
@rowenramnath2016Ай бұрын
Yes, same mind. 2 more months than Christmas 😂
@MagnetOnlyMotors Жыл бұрын
Where is your jack stand ?? Especially with a scissors jack! Oh my 😮😢.
@Nor0252 Жыл бұрын
He had the wheel under the car though,
@petemaverick45385 ай бұрын
You should invest in a torque wrench. Good video nonetheless.
@StoictionАй бұрын
2007 santa fe included?
@WB50507 ай бұрын
Ich möchte nicht, dass ich nach so einem Supermeister ein solches Auto bekomme 😱
@mriverbach62765 ай бұрын
Warum? In den meisten Werkstätten wird es nicht besser gemacht. Im Gegenteil. Hier wird halt noch ein bisschen mit der Drahtbürste den Rost abgebürstet, die Stifte neu eingefettet und der Sattel hängt nicht lose am Bremsschlauch. Die meisten Werkstätten haben dazu keine Zeit. Top. Hat mit dem Werkzeug das er zur Verfügung hat eine saubere und sichere Arbeit gemacht. Auch wenn nicht alle Drehmomente eingehalten wurden. Dann sind die Schrauben eben fester. In der realen Welt ist es eben so.
@christurner-p8l2 ай бұрын
Do u repeat on the other side b4 pumping brake pedal and replacing the resivour cap ?
@king.mecanique3232 ай бұрын
@@christurner-p8l Yes
@christurner-p8l2 ай бұрын
So you don't pump brakes until both sides have been replaced
@king.mecanique3232 ай бұрын
@@christurner-p8l exactly
@rooba636 ай бұрын
Excellent job. It's getting so hard to find a decent mechanic I'm thinking about fixing the brakes on my wife's i30 myself.
@codewalters5 ай бұрын
Thank you !
@jamesmckinney6553 Жыл бұрын
Brilliant thanks
@Tiabrine3 ай бұрын
😊😊😊
@JP-nm5by5 ай бұрын
Did he bleed brakes or need to?
@dennismadigan20232 ай бұрын
He didn't open the line, so there was no need to bleed the breaks
@richardhaywoodh7 ай бұрын
Nice job. If you wire brush the hub before trying to get the brake disc off it can make it easier to get the disc off. I wouldn’t use anything on a socket wrench to tighten up the carrier bolts because next time you come to undo them will be more difficult...