Kohler Command Governor Setting Take 2

[@JWACGB95]

OMG!!! Thank you so much. Been fighting with a Kohler 23 since last night. Replacing the carb. I didn't pay enough attention when I took the throttle rod off to know how the spring assembly was suppose to function on the governor assembly. You just saved the day for me. Thanks once again.

[@rebeccanorman9692]

THANK YOU SO MUCH YOU SAVE MY BACON!!!! I have the manual and have been trying to set this governor for 5 hours!!! You're a God send 🙏🙏

[@OmarGonzalez-uj3ot]

Great video. Thank you for the nice little tutorial. Much appreciate it. God Bless.

[@deon6860]

Thanks!! For a amazing! and helpful video.

[@IA_64]

Very helpful, thank you 👍

[@charleshogan]

Thanks for sharing this with me I've been needing to set my governor on mine for a while now it's surging bad for a while now

[@markslick8611]

Thanks for the excellent instructions.

[@petrturcovsky7035]

Thank you very much great video.

[@ZippoVarga]

Glad you liked it!

[@robertwallace5675]

Very clear,very consice,keep up the great work,the manual doesnt even describe the adj.that good,😂

[@falanmcbride]

You do not have to disconnect the throttle rod, just loosen the governor adjust bolt, hold throttle all the way open, move governor rod all the way clockwise, tighten back down. You may not have to remove the governor spring.

[@ZippoVarga]

Thanks for the tip! It's greatly appreciated Alan! Zip~

[@jimstelljes3925]

Excellent Video

[@philliphall5198]

Thank You 🙏 very good information

[@billmalec]

The key on mine was setting the shaft the governor arm clamps to first. After that everything fell right into place. Before that, nothing I did fixed the over revving problem I was having.

[@SrIrv]

THANKS BRO. THIS WAS GOOD!!!!!

[@Jeremy46202]

We're on the video that you reset the governor where did you get your breather for the carburetor

[@ZippoVarga]

I'm sorry Jeremy. I'm not sure I understand your question. You can email me at the address found in the Description box of the video and send me photos. Zip~

[@wadestewart9891]

Although it has nothing to do with a Kohler I adjusted the gov.on my 16 HP Briggs and installed a nova ll point eliminator and all my problems went away so thanks Zippo for all your videos

[@ZippoVarga]

That's great Wade! It's why I post videos so y'all can benefit from them. Cheers! Zip~

[@philliphall5198]

When you first said 60 ft lbs I laugh 😂

[@stevenbell6932]

Thank you so much.

[@jonl5889]

Why disconnect throttle rod? cant you do all of this without that step?

[@FastEddieQ]

Thank you, saved me a great deal of grief…

[@ZippoVarga]

Thanks for the Subscription Eddie! Zip~

[@ChrisThompson-ev2hq]

Ty.very help full

[@brianb5779]

Is there a way to know that this needs adjusted? What i mean by that is i have a kohler 7000 series thats 4years old (zero turn mower) for residential use. Idle hunts as well as high rpm,,,fuel filter has been changed, carb cleaned (looked great initially also). Im left thinking its the governor. Thought maybe the pump but not sure if you can check for volume output. Thanks for this video also.

[@robertruggles5584]

One closing comment you made was concerning the governor holding the throttle at idle. So, if you move the dashboard throttle handle all the way down, this releases spring pressure and the governor pulls the throttle all the way to idle. At this point, is there supposed to be any tension on the spring at all? I have a Kohler Command CV16s and at idle there's no tension on the spring. It's just floppy and sloppy in the slot which that end of the spring attaches to. But still, the governor isn't taking the RPM all the way down to idle target of 1700. I'd like to know how the governor is supposed to "hold it at idle" in this situation. What can I do?

[@johncates7038]

There is a little spring above that long larger spring. You take a pair of needle nose pliers and bend that tab to the left to take some tension off it. It's a pretty crude way of adjustment but it works!

[@xlilnetx]

Hello sir where are the next videos to series for the next arms after the governor like then cables that hook to the throttle cable

[@autorepairandmore3842]

I think my main linkage rod that goes up to throttle cable is actually backwards at bottom facing away from engine vs how this engine on video is bottom of rod where spring goes on throttle rod facing engine the correct way. I'm going to see if I can spin it the correct direction

[@dziggy3004]

BINGO! Stuck in the middle of the project right now... hopefully, this will make a difference! (will update)

[@bcm1567]

Ever had an issue with the governor shaft leaking oil? Is there a seal that can be replaced on the shaft?

[@ZippoVarga]

Hey BC. Yes, they can weep oil as the engine ages. The correct fix is to install a new governor shaft and have a bushing fitted in the wallered out hole to minimize oil seepage. Zip~

[@martinbeville7295]

Getting ready to do a sump gasket and bottom crank seal on one of these in a 27hp, looks like it be done without touching the governor assembly, by pulling the bottom pan after turning motor over to work on it, what do you think?

[@jeffvaughn9808]

I've gotta get your opinion Abt why my Kohler Courage 26 HP after cleaning fuel system and replaced all fuel line and filter cleaned carb did an ignition upgrade and I half spark on both cyl. I also set govern as per you video. Why is it still surging

[@monstercoinz9460]

So moving the throttle to fast/slow doesn't actually open the throttle valve when the motor is off? The governor automatically does that?

[@ZippoVarga]

The Governor regulates the power. When you increase the engine RPM's it's done through the governor. When you pull the throttle cable to speed up the engine, it's actually pulling the governor linkage, not the carburetor directly. Zip~

[@johnl3068]

Is the spring on bottom considered a chrome color

[@garymartin8619]

Thanks for the video

[@ZippoVarga]

No problem!

[@Chuck_S]

I done this to my Kohler Command 22 hp horizontal engine and it still runs way too fast. Even with the throttle cable on idle. Any ideas?

[@hudorim]

After 20 minutes of operation (motor cultivator) the engine (Kohler CH395) starts to give and reduce gas and then shuts down. After that it will not light up for 5-10 minutes. Most likely until the engine cools down and then starts again and runs for a while until it shuts down again. What is happening?

[@hattersequiptmentrepairllc4661]

Bad ignition coil

[@rayedison5132]

I noticed when you was holding the carburetor open its opposite of what mine is I have to pull forward to have it open and pull back to have it closed you're saying that the opposite way and I'm not understanding that unless in the carburetor has a pin pull throttle from the top instead of the bottom.

[@anthonymartinez5086]

I reset my governor as you said but I still get surging when I increase the speed. Once I lower the speed it levels back out to normal. Should I adjust the governor spring to different holes?

[@suzieq8379]

how do I put that tiny spring on the linkage I bent it just a little? do i need a new one or can I make that one work , they tiny spring on the link after you unsnapped it from that small tab?

[@johnolson733]

Is the governor lever suppose to float up and down while the engine is running?

[@ZippoVarga]

It shouldn't surge if that's what you're asking. Often that's a carb setting issue though. Zip~

[@garylohden6937]

Dose the carb need to be open or close to set it

[@gusmarrero6030]

Hello there! Will this fix my issue with It not wanting to run what seems to be idle? Choke has to be all the way on and throttle all the up to idle

[@oldscout2514]

In video you are in front of, behind, or on top of engine ? Your set up does not look like mine. My motor was installed new in 1985 or 86. I am sure some improvements have been made.since 1985. Some "Ahole" mechanic said he adjusted the governor, ran 10 minutes after l got home, blow up hole the size of half dollar in block. My son ran it out of gas a few days ago. I took carb. off, and blew it out. Now I think the governor is out of adjustment, I think l can reset the governor after watching your video. Thanks

[@todhowell5049]

Im trying to set mine. And the book said clockwise. Those butt heads. ANYWAY why did you unhook your throttle linkage from that arm. The trottle is wide open anyway. Or did you need that arm to actuly move up further than what it would with it hooked up?

[@jimbrackeen8354]

very good video. very clear. Than you.

[@jayj4387]

Great video I have a similar engine but my governor shaft has movement in and out of the engine about 3/8 to half an inch. Is that normal?

[@robertruggles5584]

Exactly. My Kohler is the same way. I have the same question.

[@CB-ug6xh]

Do you know the part number to that exact governor spring? I am having a hard time finding that one.

[@ZippoVarga]

Zilla, go to Partstree.com or Jackssmallengines.com and there, you can search for your needed parts via their large data bases. Zip~

[@oldscout2514]

I have a Koehler V-Twin. That manual on page 49( online copy of manual) says to turn governor shaft clockwise. You say counterclockwise. Which is correct?

[@ZippoVarga]

For your engine, follow the manual Scout. Zip~

[@oldscout2514]

Thank you !! Zip

[@nathanlee67028]

Same problem with me. The manual is WRONG. Zippo is correct. Turn the shaft counterclockwise, looking at the end of the shaft.

[@stevieg.4816]

I want to see someone repair a Kohler 7000 series engine that severely surges. I've done mine but after running it the surging returns. Impress me please.

[@timothygraham6601]

Great video. I have a question. Now when my kohler is running it will rev very high. And i put a spring an the opposite side of the governor spring to keep i at idle. But as soon as i move the throttle a little bit and the throttle butterfly opens slightly it starts to rev high again. What would suspect the problem is? Thankyou

[@billmalec]

The shaft the governor arm clamps to has to be set all the way clockwise or counterclockwise first. Try one way first and see what happens. If that doesn't work turn it the other way. I swear mine went all the way counterclockwise but I could be wrong. I thought my problem was the spring location also and it wasn't. It's that rod.

[@guillermotroncoso4276]

Where I could buy a parts for these lawn motor.

[@ZippoVarga]

jackssmallengines.com, partstree.com, Amazon, eBay.

[@jefferyspinelli7952]

Nice video but the adj should be done with the clip in the hole

[@ZippoVarga]

This was following the Kohler Technicians Manual. I thought what you thought as well and it made more sense to me to do it with the throttle rod attached. No clue what wacky tobacky they were smoking when they wrote that lol. Cheers Jeffery! Zip~

[@ronnierussell5904]

Boy he sure made a job out of something simple.

[@palmrose2]

Ha ha ha. I love your vids Zip, but when I heard 60 lbs/ft on that little nut, I thought, sure. You won't do a bit of damage.

[@ZippoVarga]

Yeah, I'm glad I caught that flub! I'd have gotten some serious flack over that for sure lol. Cheers palm! Zip~

[@michigantler5046]

thanks

[@robertyearian227]

Hey zippo I got kohler 20 hp need set governor hellllp

[@moparmadman1134]

Trying to remove the governor gear ,do you need a special tool

[@larsrodbok1285]

First view, wahoo!

[@ZippoVarga]

lol. Congrate Lars! Great to see you stopping by for the edited version where I corrected a mistake I made while taping. Cheers! Zip~

[@larsrodbok1285]

Always a treat to watch your videos, Zippo!

[@ZippoVarga]

Glad you like my style! It's not for everyone! Cheers Lars! Zip~

[@bobmay9887]

Good info but wow makes it like watching grass grow with that presentation