What most don't realize is, the PCV system also allows vacuum draw on the flimsy oil control ring and 2 compression rings which allows better sealing against the cylinder walls at higher RPM's .This is engine design 101 .If supercharged or turbo charged then this is a good mod,not NA.I run 2 oil catch cans to my PCV valves .To note: some supercharged drag raced V-8 will use the exhaust to pull a vacuum on the engine crank case/piston rings for better sealing at higher RPM's as well.
@imsurroundedbyidiocracy6 жыл бұрын
There is less and less vacuum as engine load increases which happens as your rpms increase unless you let off the gas and the throttle bodies close which in turn drops the load. This is engine dynamics 101. Additionally while you are correct that drawing a vacuum on the crankcase will help those rings seal the real sealing effect on a road car comes from the combustion gasses applying pressure on them and those gasses making their way down the ring set due to ring gap or nonuniform sealing by the rings against the cylinder. An OEM engine and PCV system will pull only a few PSI on the crankcase and that is only at idle and is really the only measurable place a benefit is seen. Again this vacuum and benefit decreases the higher the load. Only an actual vacuum pump system or exhaust scavenging system that you referred to will draw enough vacuum above idle to cause the event you are referring to. This is easily verified by comparing the vacuum the engine naturally draws vs the pressure that the crankcase experiences from the blowby gasses. Again, engine dynamics 101. Lastly a boosted application really needs a catch can setup due to the increase in blow by and using this kit would not be a wise decision as the blowby volume is too great and really needs a can so the oil and water can fall out of suspension into the can.
@rockybagga46276 жыл бұрын
You're right it dose not make sense to have an PCV delete on NA motor. 🤔 One thing it "might" help to do the PCV delete if oil is build up in the intake manifold. I mean still.
@heilong_q505 жыл бұрын
Dino Maxi you got pictures of your catch can setup? I was thinking of doing the same to my 3.7 Q50
@goldfishAS5 жыл бұрын
Could you do a review video on the HPS intake tubes?
@Baroy10105 жыл бұрын
when you do pcv deleted, the engine release smoke through the tiny filters and you can smell burned oil so I don’t like that
@timtaylor95905 жыл бұрын
may as well do a catch can and run a tube outside the engine bay for a breather filter
@g32k4 жыл бұрын
Well when you don’t do it that goes into the intake so
@PistonAvatarGuy4 жыл бұрын
@@g32k PCV helps remove combustion gases from the crankcase, which improves oil life and helps reduce wear on your engine. There's not really any reason for it not to go into the intake, it's just blow by anyway.
@g32k4 жыл бұрын
PistonAvatarGuy until you’ve cleaned out an intake manifold with 70-130k miles which is what most of these cars have you won’t realize how bad it can really get I bet most people with a high mileage engine could clean their tb/intake manifold/heads and actually pickup power on a dyno lol.
@PistonAvatarGuy4 жыл бұрын
@@g32k It depends on the engine, I've seen 300k+ miles with almost no oil in the manifold. If oil is making its way into the manifold, it's better to put an oil/air separator in the system, rather than eliminate the PCV system altogether.
@dylanscott64852 жыл бұрын
This is awesome, Thank you. I can't get over that fact that you put the connecting parts of the zip ties facing up though... it would look so much better hidden and just showed the flat part of the zip
@ILoveYahuah316 Жыл бұрын
Thanks man. I just bought an AAM COMPETITION upper intake manifold and this was just the information I needed to go with the install. I just purchased it. $150 upgrade. I have an 08 G37 Coupe. If you are going to install a nice Upper intake manifold you must have this kit. I haven't installed my new intake yet because of knowledge. I'm new to everything and my new intake doesn't even have the ports in the front because it's made for this upgrade. So thank you again. This video really helped me.
@kova_motive Жыл бұрын
Glad it helped!
@Noneofjoebusiness2 жыл бұрын
Where’d you get the plugs? The silver ones for the intake. My resonator broke off, can I just run the hose without it to connect it?
@inasimulationwelive3 жыл бұрын
Those things you use to replace the pcv valves had holes inside?
@colewo927 жыл бұрын
Man you're killing the game with videos on these G's. I never have any questions/concerns after I'm done watching. Just ordered my PCV delete kit from EPS Tuning this morning because of you haha. Just waiting till I have my other mods first, then doing it all at once. Maybe a video on the Akebono Big Brake Kit upgrade?? Just a thought!
@elijahowen17273 жыл бұрын
Sorry to be offtopic but does anybody know of a method to log back into an Instagram account? I was dumb forgot my account password. I would appreciate any assistance you can give me.
@jairojaxon95043 жыл бұрын
@Elijah Owen instablaster :)
@elijahowen17273 жыл бұрын
@Jairo Jaxon Thanks so much for your reply. I got to the site thru google and I'm waiting for the hacking stuff atm. Looks like it's gonna take quite some time so I will get back to you later with my results.
@elijahowen17273 жыл бұрын
@Jairo Jaxon It did the trick and I now got access to my account again. Im so happy:D Thank you so much, you really help me out :D
@jairojaxon95043 жыл бұрын
@Elijah Owen you are welcome =)
@hamdanahmed26647 жыл бұрын
what did u gain after deleting your g37 PCV system? i would like to know please
@waugy370z85 жыл бұрын
You no longer get the oil residue coating the inside of the intake and building up on the intake valves. Since these are direct injection engines there is no gas spraying on the intake valve like in a port injection engine. Now since car manufacturers are seeing the issues with a pcv system on direct injection engines they're coming from the factory with oil catch cans. Or they now have both direct and port injection.
@yashasan835 жыл бұрын
Waugy 370z vq37vhr is not a direct injection engine
@waugy370z85 жыл бұрын
@@yashasan83 Yes it is. www.engine-specs.net/nissan/vq37vhr.html
@yashasan835 жыл бұрын
Waugy 370z I’ve taken my engine apart on my 370z and i guarantee you it is not direct injection.... in direct injection the fuel injector is mounted so it sits inside the combustion chamber, the fuel injectors on the vq37 are not mounted there, they are mounted on the intake manifold, therefore it is port injected
@waugy370z85 жыл бұрын
@@yashasan83 After i read this last comment i thought "damn it someones wrong here" and it was me. And im glad you kept after me. Listen, google it or whatever and every single site says direct injection. Even that spec sheet I forwarded in my last comment. Thats the whole god damn reason i wanted a pcv delete. Anyway i looked up injector replacement on KZbin and found a video pretty quick and sure as shit they were in the intake runner. Thank you for keeping at me and not doing like some people and being ignorant right away. Seriously though look it up cause theres a lot of people calling what we got direct injection. Thanks and take care 👍
@tonylopez52396 жыл бұрын
Is there any part #s on the fitting that thread on to the valve covers
@numutekwipu20065 жыл бұрын
Quick question I have a Fx35 VQ35 3.5 V6 I see that u have 2 throttles I only have 1 throttle can I switch the top manifold and place that one u have on mine has that ever been done ?
@my737373737 жыл бұрын
Is it possible to just put a filter on the tube coming out of the pcv value or does it need to be bypassed? Also, do you need to get your engine re tuned after this because crank case pressure is free to leave without the valve? Thank you !
@OxXxnard7 жыл бұрын
Will it should be possible just gotta block off all other valves. Ima go ahead and try it. There should be no difference
@mitchellmitchell69387 жыл бұрын
It was always free to leave it's a check valve. One-way flow Doug
@uthanwintun6 жыл бұрын
is there any option to fit a relief valve or similar to prevent high crank pressure in case of filters getting blocked? thanks
@TennisWorldSetPoint4 жыл бұрын
Question I didnt do the delete kit when having the cold air intake I stalled. It seems that the shop tied a bunch of hoses at the ends. Now I'm worried I could get oil in the takeda intake? Went to Speedworld figured they would know how go do everything correctly. Suggestions
@r.c.8505 жыл бұрын
Deleting the PCV system will fix blowby?... I have some steam and smock came from the oil cap. I believe i have bloyby problems. But doing this will fix the too much pressure??
@myvideotablemyvideotable5285 жыл бұрын
No. Because blowby increases as the engine ages and your piston rings are worn.
@myvideotablemyvideotable5285 жыл бұрын
See more videos on how much blowby is normal. Can easily test it .
@jimleonetti6575 жыл бұрын
Can you run both hoses into a tee and one filter
@epuga157 жыл бұрын
so is there a noticible difference with the silicone intake tubes? and would u recommend hps over mishimoto?
@kova_motive7 жыл бұрын
I don't think there would be much of a noticeable difference just with the tubes. But, with the tubes and K&N drop ins, I noticed a slight power increase and better throttle response. HPS and Mishimoto are basically the same design. I would recommend either.
@eleazararellano39577 жыл бұрын
AlexKayRN. hi .hey brother from where can i get the pcv delete kit for my. 2013 g37
@michaelperry39295 жыл бұрын
Hey man. I don’t know if you’d have any thoughts on this, but I have been chasing this problem for months. My 09 g37s will randomly throw a p0300 (random misfire) code, but only on first start up when engine is cold. After that it will not throw it while driving and can turn car on and off all day with no code. Have done coil packs, spark plugs, both primary o2s, pcv valves and car has been tuned on uprev. I’m at a loss at this point. Have any suggestions?
@michaelperry39295 жыл бұрын
Do I need to take it back to who tuned it for that? Or have it returned?
@michaelperry39295 жыл бұрын
Retuned*
@Avus954 жыл бұрын
Excellent and informative video! Question: Do those little breather filters ever get oily over time from the PCV vapors? Is is this pretty much an "install it and forget about it" type of mod? I think I'm going to get this kit soon for my 2010 Nismo 370Z. Install should be exactly the same except for the added step of removing the strut brace before you can remove the engine cover.
@samokash6 жыл бұрын
Hopefully I can get this question answered. So is the EPS PCV install process a little different for a G35 (same engine) VQ35HR???
@TheShazteck3 жыл бұрын
What is the size of the an fitting going into the valve cover ?
@myvideotablemyvideotable5285 жыл бұрын
Alternatively, just add a catch can and route it back to intake manifold. Just go for a drive on highway at least once a month. The engine doesn't really need to be clean as a kitchen table.
@MikelGoodman6 жыл бұрын
I had the same issue with my skyline, and just want to say thanks so much, it worked perfectly.
@JoshuaClaypool7 жыл бұрын
What made you decide to go this route over catch cans? I've heard about issues with oil residue getting all over in the engine bay with a PCV delete with filters. I'm interested in doing one of these upgrades (delete or catch cans) at some point in the near future, but I'm on the fence as to which. Thanks!
@kova_motive7 жыл бұрын
Thanks for the interest, much appreciated. I went with the delete over a catch can mainly for ease of placement and cost. If you don't have a catch can integrated into your coolant reservoir (can be expensive), you have to find a spot for it and sometimes it can look out of place. With the engine cover on, these are hidden very well and don't stick out. Also, I've had this same delete on my Z for a while and haven't experienced residue getting all over. Plus, with this kit, if you run your engine cover, any residue that may occur will be blocked by the cover and won't get all over your engine bay. Hope this helps!
@Sergio-rn7os7 жыл бұрын
AlexKayRN why is the link to buy them for the 3.5 not 3.7, is it the same cause 07 and 08 g35 have the same two throttle body in engine. so if my car is a g37 I can buy the $80 kit?
@kova_motive7 жыл бұрын
S. Quesada The kit for the VHR is not listed on their site. You have to message them and they will take care of you. The VHR and HR kits are different.
@Sergio-rn7os7 жыл бұрын
AlexKayRN I see it thru administration tuning, but it's thru other website it looks different with catch cans. how much is this one? Thank you.
@kova_motive7 жыл бұрын
The Admin Tuning one is a catch can. If you just want the delete, that is thru EPS. It is about $150 shipped.
@BTBGARAGE Жыл бұрын
Do I need a retune for this if I already have a tune?
@kova_motive Жыл бұрын
No
@lbbburke99064 жыл бұрын
Hi cuestion ...to l kent used My PVC valve in 2 house un put to liro filtro to?
@miguelv_1055 Жыл бұрын
Can you do oil catch can and pcv delete ?
@MetroCollectablesandvlogs7 жыл бұрын
Thanks for sharing. Just bought some HPS tubes but noticed they have the resonator spot for them. Any ideas where I can get the plugs that came in the kit? I don't want to put resonators bk on. Thank you sir
@jaxen-x12165 жыл бұрын
I do like the ideal behind the delete kit, but what happen when the 2 new filters installs get too dirty and need to be replaced over time? Are the filters a standard item that can be purchased from any auto supply store or do they need to be purchased from the kit supplier? Either way, what is the reference part number?
@leedavis74546 жыл бұрын
I Installed This Kit on My 2008 G37S and now I get Crankcase Fumes In the Cabin when Running A/C Or Heater Blower...HELP !!!
@demonmodz23315 жыл бұрын
Lee Davis stupid that’s how it works
@Ivan.Nismo00184 жыл бұрын
Get oil cach cans instead of pcv delete, that will fix your problem.
@DocHavoc05126 жыл бұрын
Do you know why you need AN fittings for the PCV system?
@celestecarbonel55077 жыл бұрын
This is actually a PCV Question... * See below I would love to know your opinion on my VQ37VHR "Infiniti M37" 2012. I HAD a serious Engine sludge Problem "HUGE"! Basically did several serious douche tricks/Flush. Basically a rebuild, so I chose to throw in modern Chemistry and some old school flush... Used 50% diesel fuel in Crankcase. Had P0301, P0340 and YES P0011. Evidently oil-sludge made its way pasts rings on Cyl 1. Replaced plug and checked compression on 1 and She idles great no P0301. I replaced both Camshaft sensors and CPK... also cleaned both solenoids IVT. Vehicle runs great, but still in limp-mode at 3500 RPMs. Its driveable and no hard shifts as long as I DONT HIT 3500 rpm. "Im good with that for now"- Im a Uber driver! I will bench test sensors soon. " Pretty sure its still Sl;udged" *My main Question is about PCV system: It started blowing lots of smoke after repairs. I cleaned valves twice kinda worked? Decided valves were trash and decided to plug intake and just remove valves (let it breath) until new valves were delivered. Smoke STOPPED! * I just replaced 1 PCV valve (they only had 1 in stock) and it immediately started smoking. I bought valve from Rock Auto "Intermotor # V503". Is the valve defective or is there more to the PCV Problem? Also.... I cant find "shit" about this motor on KZbin??? I will continue to post and communicate...I'll even do a video when All problems resolved. Please facebook me at (Peppi Manton "Dj earpu5e"). More than happy to give you music and my videos for colab and use messenger. Really need your input? FYI trims are good
@Dolson8612305 жыл бұрын
Galley gasket, don’t drive it
@chrisc25825 жыл бұрын
Doesn't oil build up in those filters and leak?
@alexwilcox95596 жыл бұрын
Are the silicone HPS post MAF tubes worth the buy? Im curious because they look much nicer, but I feel the claims they make aren't truly accurate
@SpeedCultureStudios5 жыл бұрын
I would say they are worth buying, if you haven't already. I've done a video on this, but I don't think they increase power at all, but combined with a set of high flow drop in filters, they reduce turbulence into the engine making it more efficient. If nothing else, they clean up the engine bay and can reduce heat transfer from the engine to the intake air as silicone is a nice insulator!
@Maxrizzz4 жыл бұрын
so whats a better oil catch can ? or pcv ?? help please !
@e7bk5 жыл бұрын
PCV valve used to remove unburned fuel inside the engine, I advise you to put it back without filters only keep oil catch can
@dimitrovbmw4 жыл бұрын
yea, whats the point of even putting filters there... this kit is a nonsense, the filters are good if there is a sucking in this case there is pushing from the crank case out therefor there is no need of filters there! those people are clueless!
@e7bk4 жыл бұрын
@@dimitrovbmw correct, also it doesn't work if you connect the filter on air intake manifold hose if delete the PCV valve because the air will bypass air mass sensor
@dimitrovbmw4 жыл бұрын
@@e7bk the only correct way to do this is by installing good catch can only with out removing anything! The vacume is what sucks the shit out of the crank case therefore less build up is going to be accumulated there!
@el34glo595 жыл бұрын
What did this accomplish? Sorry I'm honestly not too familiar with this procedure. Just residue for the intakes?
@waugy370z85 жыл бұрын
Yeah it keeps the oil residue thats vented from the crankcase from sticking and building up on the throttle body and the air ducts connected to the throttle body. If you look at the throttle body of a car that vents the crank case back into the intake, the front of it will be caked with oil in a sludge type form. I changed mine over around 50,000 miles and im so glad I did. Everyrhing was gummed up with that crap. My car idled smoother also aftwards. And these engines are direct injection so they dont get the gas sprayed into the intake which helps keep this problem under control to a point. Defiantly worth doing.
@jacquesc31662 жыл бұрын
@@waugy370z8 Lol so much wrong with this comment. Start with understanding that this in fact a port injected engine, not a DI engine. Then look at where the PCV connects into the intake tube. Then understand the actual benefits of a catch can. Changing the TB(s)? What for?! At FIFTY thousand miles??? 🤣
@KevinWilliams-ie7oe6 жыл бұрын
Okay I have a 2008 G35xS. Will the g37 pcv kit work on my g35? It has the same dual throttle body set up.
@neonskyofficla6 жыл бұрын
HR and VHR will need different kits
@rizocars61156 жыл бұрын
What I im missing? You didn't show what did you do with the hoses that go from the pcv to the intake manifold, not the ones from the air intake to the valve
@Avus954 жыл бұрын
Did you even watch the video? That was what the 90* elbows and -AN fittings were for. They connected to those little breather filters that then sit in front of the now-blocked off nipples on the intake plenum.
@Night_Watch4135 жыл бұрын
How do you like and rate the hps intake tubes
@makaibonaparte33613 жыл бұрын
Where did u get dis kit from I need one myself please
@JustJJ5557 жыл бұрын
Did you see any improvements or changes by getting the HPS intake tubes? And what air filters are you running?
@kova_motive7 жыл бұрын
I can't really say if I noticed a difference with just the tubes as I installed them at the same time as my K&N filters. The combo seemed to add a little pep though. Nothing crazy but a little.
@michaelmorell74514 жыл бұрын
Ventilating to air/ozone is illegal. Leave your PCV valves. Install a 2 double, cheap oil catch cans, with barbed fittings at the drain bottom. Run hoses down to a (Y) fitting then to a valve near bottom pan for draining. Put a piece of steel wool in ea. can to prevent splashing. After your all done, clean valves. Combustion chamber, piston tops of all the burnt oil and carbon. Then clean the plenum and throttle body as well. All of this will save your 02 sensors and cats too. Recommend this for all cars. Even brand new
@Joel02974 жыл бұрын
Why don't u use oil catch cans?
@eastpaloalto6502 жыл бұрын
does this require a tune to do it ??
@cristiansalas24583 жыл бұрын
Are the valves hallow?
@BiZalLiNTV7 жыл бұрын
I agree that using a pcv delete kit should in theory raise octane rating and reduce knock. But that creates a massive vacuum leak and the cars prolly not running as good as it should and you dont notice it. Also, it will require more force to move the piston down in the cylinder. Now for emissions regulations, you will never pass emissions inspection. New vehicles come with pcv system monitors so pcv and evap wont "ready up" for emissions.
@kova_motive7 жыл бұрын
comdawg Not sure about other cars but the PCV system on these cars is not connected to any sensors. Also, its basically a ventilation system that re-routes vented oil/air back into the intake system. Only different is now its venting into the filters/atmosphere instead of the intake system. Doesn't negatively affect the functioning of the engine at all.
@johnboy56324 жыл бұрын
Hi I'm new to your channel...... So I'm not quite clear what are the benefits of deleting your pcv valve? So if this is done. An oil catch can is probably recommended?
@kova_motive4 жыл бұрын
Deleting your PCV valve or running catch cans helps to eliminate oil being circulated back into your intake system. This causes intakes, TBs and intake manifolds to get gunked up. Usually you either do a PCV delete OR a catch can, not both.
@johnboy56324 жыл бұрын
@@kova_motive oooooooh. OK. I've seen alot of guys do the oil catch can thing. I have an 08 infiniti g37 coupe. Love it! I plan on getting a full motordyne catback coupled with Berk hi flo cats. Then I'll look into doing the ecutek tuning done..... Your video pushed me over the edge to get that done.... I know alot of G owners are doing that.... Oh Btw do you know what a Sprint Booster is? Thanks for the Reply
@aomaggots-6 жыл бұрын
Hey man! Do you know why the MFG wouldn't design the Z like this in the first place? It seems so obvious...
@dynamic216 жыл бұрын
Emissions laws.
@oscaraguilar79036 жыл бұрын
I have a q50 3.7 it's the Sam's engine as the q60 but the q50 is not on the list of the VQ engines. Does anybody know the difference its the same platform as the VQ 3.7 engines
@alexanderbmx5 жыл бұрын
I think you have the vqHR motor.. If you do.. Then all g37s mods will work for u
@370gtalej56 жыл бұрын
Damn. I must buy this soon! Hey quick question. Is there a certain point those tiny filters are to be changed or clean?
@hezharanya5 жыл бұрын
I dont see why could not just Wash it with degreaser soap n let it dry completely .
@dres10814 жыл бұрын
What size are those filters
@pmote003 жыл бұрын
Does this work for a Vq35hr?
@07wrxtr17 жыл бұрын
Very cool. Seems like a good idea especially with all of the TB issues on the forums after higher miles.
@kova_motive7 жыл бұрын
Yea, this will really help to decrease the gunk/sludge build-up in the engine. From my experience, the VHR seems to suffer more from this than the HR. When I deleted my PCV system on my 350z, my intake tract wasn't nearly as dirty as my G. Def a mod worth while that will help in the long run.
@mohdezwandymohdsulaiman5 жыл бұрын
I don't get it. Right now you just install on on valve cover breather or pcv?
@dimitrovbmw4 жыл бұрын
Its better that you didnt get it, because you will save yourself a lot of trouble later on by doing this nonsense.
@trd27277 жыл бұрын
Alex is this kit the one that's $80 on there website says 350zhr? Will be the same for g37vhr
@kova_motive7 жыл бұрын
No, this kit is specific to the VHR and comes with many more pieces than the HR kit. If you message EPS on facebook, they will be able to hook you up!
@trd27277 жыл бұрын
I see thanks bro!
@kova_motive7 жыл бұрын
No problem, they'll take care of ya!
@Sergio-rn7os7 жыл бұрын
AlexKayRN what car you got a g37 or g35?
@kova_motive7 жыл бұрын
S. Quesada G37. The VHR kit isnt listed on their page. Just send a message and they'll take care of you.
@bccapone8374 жыл бұрын
Great video bro. Just to clarify is it two open tubes with filters on both sides ?. how has oil consumption been since and does yours chuck oil out 👍👌✌
@kova_motive4 жыл бұрын
Yes, 1 for each side. This won't change oil consumption. If your car is consuming oil, it still will. It will just show up on your filters instead of going back in your intake. If you don't clean the filters regularly, yes, there will be a build-up of oil.
@ThePunkabahkau3 жыл бұрын
What is the pcv thread size? In NPT?
@kova_motive3 жыл бұрын
Not sure off hand.
@cris258407 жыл бұрын
do you get any oil vapor smells from doing this mod?
@kova_motive7 жыл бұрын
cristian rodriguez I haven't noticed any. Had this mod on my Z for over a year and never noticed anything.
@oldirtydave226 жыл бұрын
Why didn't you go cold air intake?
@SpeedCultureStudios5 жыл бұрын
Because they yield very little results for the cost. K&N drop in filters have been proven to net you just as much power in the end as cold air intakes. $100 for filters vs. $400+ for intakes for the same amount of power and throttle response. Easy decision!
@coles_infiniti2 жыл бұрын
Definitely going to do this on my 08 G sedan! Thanks bro
@TopShelfGear7 жыл бұрын
hey Alex, have you seen the 70mm EPS throttle body kit?
@kova_motive7 жыл бұрын
I have. I would only get them if I re-did my whole intake setup to include ported manifolds and 3in intakes. Not sure what route I am going performance wise for the G, So I am waiting for now.
@EATSLEEPJD7 жыл бұрын
Same for the 3.7l Q50?
@kova_motive7 жыл бұрын
Jithin Daniel Yup, same engine.
@Rixhz347 жыл бұрын
your videos are great and dont take this wrong but please do us all a favor and do not use that song at 5:55 it's horrible
@kova_motive7 жыл бұрын
Thanks for the input.
@Rixhz347 жыл бұрын
AlexKayRN no problem I hope u didn't take it the wrong way my dude your videos are great
@kova_motive7 жыл бұрын
Rich Not at all, constructive criticism is appreciated. Hard to find decent music that isnt copyrighted.
@Rixhz347 жыл бұрын
AlexKayRN I hear you, my wife runs a successful KZbin channel and that was one of her biggest issues. last thing you want is a strike but try reaching out to up and coming artists. You'd be surprised how much of them reply and give permission. if you don't want to go that route just Google search royalty free music, you'll have thousands of options
@kova_motive7 жыл бұрын
Rich Great, I'll have to do that. Thanks for the advice!
@lukerutherford32933 жыл бұрын
Can I delete just the front side
@r7blue2 жыл бұрын
you can find other pcv delete kits for around 40$ which id say its worth buying for 40$ since you can source all the parts your self for around 40$
@s.maverickharrisonii60196 жыл бұрын
Can this be did to a 2007 g35 x
@roosterhowerton77556 жыл бұрын
Hey dude... great vid.. the questions I have.. how often do you have to change those delete filters.. and once you started the vehicle.. did your ECU throw any engine codes.. thanks..
@BigKfishing7 жыл бұрын
so this mod inst for performance?
@melhemsaidy17076 жыл бұрын
how to buy the kit other than facebook?
@davidthetico7 жыл бұрын
Thanks really helpful I hate having oil in the intake on my coupe
@kova_motive7 жыл бұрын
Glad I could help!
@ken6x7 жыл бұрын
I bought this same kit and cant get my car to run right. The idle jumps around and dies every once and a while. Anyone else run into these problems?
@kova_motive7 жыл бұрын
As long as you hooked everything up correctly, you shouldn't have a problem. There's no sensors connected to the PCV system.
@OxXxnard7 жыл бұрын
Gotta make sure you have not vacuum leaks. That’s what is causing the problem
@wrxsubaru027 жыл бұрын
Isn't it good to have a little bit of oil fumes going into your intake? it kinda coats everything to prevent corrosion right?
@MrAri1969md6 жыл бұрын
That was cool man. Can I ask you a question about something that's happening to my 2010 G37?
@myvideotablemyvideotable5285 жыл бұрын
That hose should run all the way to the rear of car and a baffled can in between so not to spill drops of oil on road. Becus the filters will clog up later and also those fumes in engine bay are very bad.
@hamzaakram45017 жыл бұрын
My infinity 2016 MODEL pcv vale lekd way brablam plz help me i m new pcv veale sam lekd
@mitchellmitchell69387 жыл бұрын
Huh?
@rianatraxler59806 жыл бұрын
Mitchell Mitchell I think he’s trying to say his pcv valve leaked and it’s a big problem, he’s new and his valve leaks 🤷🏽♀️
@richbf27 жыл бұрын
Thanks for posting a detailed video about it. I saw a 2013 Z that I was interested but as soon as the hood pop up and I saw engine without cover, I got scared and found excuse to turn down the deal (vehicle comes with aftermarket exhaust, stillen intake. Everything I want). Now I know why previous owner got rid of the cover.
@kova_motive7 жыл бұрын
richbf2 There are many reasons to remove the cover. Just make sure the car was well taken care of.
@scottyscott18986 жыл бұрын
Should have got it with all that already put on it.. unless it was just priced too high
@clark85115 жыл бұрын
im doing the same bro. thanks for the video demo.
@610savages86 жыл бұрын
what is the horsepower increase
@TheSnake1997PSN6 жыл бұрын
StealthGamer lol nothing. All that kit does is expose your blow-by gases to the atmosphere. No power gain, no benifet. Good money grab lol
@stanleyshie76467 жыл бұрын
catch can , dont delte pvc, let it flow nthrow the can... i use a 3 way heater hose conection so i onyl hae one breather.. isntead of tweo
@kova_motive7 жыл бұрын
That's an option as well.
@dylansides75373 жыл бұрын
My new engine came with broke off pcv valves anyone have this problem?
@GuyX20136 жыл бұрын
The video was put together nicely but this mod makes no difference to power output to an NA engine which I understand wasn't one of your reasons but worth mentioning as well. Since oil will no longer be getting back into the engine , it will overtime get all over the outside of the engine, those filters never really stop the fine oily mist coming from your engine. This mod seems like it's more trouble than what it's worth on an NA engine that is so finicky to begin with all that electronic bullshit everywhere and its tight fitting.
@bn42416 жыл бұрын
Hey man. Do you know if they make these kit for 2015 Infiniti Q50? I looked everywhere and I haven't been able to find any.
@SpeedCultureStudios5 жыл бұрын
I spoke with EPS about this and they don't make one specifically for the Q50 and said they haven't tested this kit on a q50 but don't know why it wouldn't work. He basically told me to buy one, try it and let them know...I didn't really like that response, so haven't made the purchase yet. I don't see why this kit wouldn't work.
@bryanvelazco83697 жыл бұрын
I like it bro ,really nice ,!!!!where can i buy this kit i have the same car and i will like to install it in my car !!!!
@kova_motive7 жыл бұрын
Awesome! Here's the link to their store. facebook.com/pg/epstuningtx/shop/?rid=1580249515526213&rt=39
@drevaughnwood20583 жыл бұрын
ordered, thank you sir!
@stephenmatos4682 жыл бұрын
That's Awesome.. I have a G37,I will be doing that to mine.. Thanks for ybe Info.
@ovidiscool7 жыл бұрын
does this apply to the 350z vq35hr motor
@kova_motive7 жыл бұрын
ovidio vasquez This kit is specific to the VHR but the HR kit and install process is actually easier/more simple.
@kossac24922 жыл бұрын
chad install man, Very cool
@518jeremias7 жыл бұрын
Motordyne M370 Manifold next?
@kova_motive7 жыл бұрын
I'm going to keep the intake side of things the way they are for now. The VHR manifold flows super well. I might work on the exhaust some more down the road and make a custom true dual exhaust and maybe cut down on the drone some.
@Malte-Micha7 жыл бұрын
Will it work on G35??
@kova_motive7 жыл бұрын
Not this exact kit, but yes, you can do this on a G35
@mcfragil2 жыл бұрын
so what's the point of doing this to your car?
@marcsolorzan94873 жыл бұрын
Ima pretty much assume that your installing a hardware version of snake oil bro. Deleting that system maybe bad for your car, and or may make you fail smog. If it was that easy nissan engineers would have done it without zip ties.
@tatankahaska6 жыл бұрын
Awesome video !!
@Eric486348637 жыл бұрын
nice vid short and sweet thanks!
@9thgizzyguy5 жыл бұрын
Why not just get an oil catch can kit ? Sometimes my kids are in the car and the last thing i want is them smelling nasty burnt oil fumes every time i turn on the Ac or heat. Im good ‘ catch can kit for me 😎
@kevinalvarez33247 жыл бұрын
Guys I need help I am going to get a g37 and I want to modify it but also don't want anything to crazy but also want to increase hp can some one give me suggestions
@datkidelmo7 жыл бұрын
Arctic_ Max K&N drop in filters and a catback exhaust starting off will give you a nice power gain especially across the mid range
@mitchellmitchell69387 жыл бұрын
Here's the real. Without turbo or supercharging you can spend thousands of dollars on exhaust and intake modifications and only gain 15 wheel hp. This is not an LS motor. Bolt one don't do shit for this car.
@timothyfranco98646 жыл бұрын
Love it I want this kit!
@Japalian247 жыл бұрын
Damn. Dude i love your channel nice! Keep up the good work. Subbed.