Laser Distance Measurer - LMG50 - AEG Powertools

Point and shoot system - one person measuring with only one simple press of a button. Area, volume, height and width measurement
ae.aeg-powertools.eu/products/...

[@loveloveiloveuforever7247]

Great product!!! Would buy again.

[@parekuy]

Can I calculate elevation and azimuth using this tool? Basically i want to get blockage zone on an active satellite antenna.

[@petez7140]

So I see where it calculated the surface area of a wall that was elevated and not easily accessible. I assume it should be able to just do height or length as well. Can anyone confirm?

[@rajeshharsora5806]

is there machine which measure in exact mm wall to wall iam alluminium window maker in mumbai i take mat by tap in inches n 13/16 ect

[@armorvestrus4119]

It looks great but is it useless outside?

[@stamdrako1975]

I test my laser measure with 3 other and is out 3mm how can I calibrate my AEG laser distance?

[@surveykamal3924]

Thanks

[@tomprovan6817]

Does anyone know of a 90-degree Target that a person could put on a 2 x 4 and use this like a tape measure?

[@rishabhshirke1175]

how do you know that you are pointing exactly at 90 deg?

[@shadyabu-raya6751]

Rishabh Shirke I am waiting for the answer of this question since 1 month..... how can he be Sure, that he is pointing in 90° ...

[@shadyabu-raya6751]

I bought a Hilti PD-E . It has a integreated compass. It Shows the degree in vertical Modus. And in horizontal modus you can pic the short distens to the wall. This will be the 90°

[@SurfnPics]

You simply go by eye unless you need a more accurate measurement then hold a framing square at the rear surface and follow the 90deg straight

[@vishnuvkumar-fn8qd]

In Bosch GLM series it shows spirit level like bubble in screen..by using this function we can level 90 degree

[@technicalmentor5192]

how to measure outer and inner length of elbow

[@daaanger000]

how exactly do you know what your pointing at? it there a laser res dot or something

[@AEG_Powertools]

Hi, yes there is a small Red dot to indicate where you are aiming.

[@vishnuvkumar-fn8qd]

How can I measure horizontal length indirectly???

[@armorvestrus4119]

It has the Cosine feature he uses it in the video to show the horizontal length.

[@aampudia8]

i'd love to have a tool to measure distance indirectly without having to point it at 90° afterwards.... it can be done with a distancemeter and a 6 DOF IMU knowing the angle between both measurements.....

[@johnsmythe1744]

yes, it's hard work pressing buttons

[@aampudia8]

john smythe it's not to save me from pressing buttons, it's that I need to measure pipes remotely, and all those laser distance meters need a perpendicular measure, and that's not always possible, and even if it is, if you don't have it perfectly perpendicular it affects it's accuracy a lot....

[@johnsmythe1744]

fair enough. I only ever use them for estimates. When it comes to installation tapes are far quicker and convenient and everyone has one. Our pipes only come in 6M lengths so tapes are more than adequate. Now that I think, measuring a section of pipe to be cut with a laser would be way more trouble than it's worth, possibly requiring 2 people

[@dooda1193]

how to measure angle.... left to right if i am at center

[@ClaytonInman]

Is this tripod mountable?

[@tomprovan6817]

I haven't seen that in any ads but I would like to know that answer as well

[@manohoo]

terrible example on how to use the device accurately, holding the device with your hand?