Tesla Valve | The complete physics

[@SabinCivil]

kzbin.info/www/bejne/paupc6aDrt53iac - Here is a simple experimental demonstration of the Tesla valve. Some people have casted doubt about its effectiveness. Trying to understand the Tesla valve and Nikola Tesla's mind was a real fun. Thank you for the love :) Your support is needed to keep this channel alive - www.patreon.com/Lesics Cheers Sabin Mathew

[@MmMm-gz6sp]

Thanks for the time of your's, it was more then just helpful

[@systemerror-tg2dx]

can it create vibrations due to vortices generated in divergent flow?

[@TheCarpenterUnion]

I think you over estimated the amount of steps Tesla would have taken to developing this. It is trivial to realize that forcing fluid back on itself will cause a high reduction in flow. To me it seems the first step would be to start with a series of the lobes that we see, then adjust the angles between them to be optimal, rather than what was displayed in the video. Granted, your intent may have been to demonstrate the way a modern engineer would approach the problem, which would have been fine had you not portrayed it as Tesla's design process.

[@puckspirit2573]

I'm actually considering to use it in a work application. Could someone help? The thing is, we have a centrifugal pump with DN70 inlet, sucking fuel from a tank. But we also need to create pressure in front of it, using a specific gear pump. We tried using conventional one way valves to keep gear pump from just sending fuel through a loop, but it ends up just closing them and suffocating the centrifugal pump. Will Tesla valve work in this scenario, when you have a flow going one direction, but pressure is coming from the other one. Seems kinda impossible when put into words, but I hoope there's someone here, who can help

[@deathskayebolo6806]

What happens with superfluid if you use and expansion chamber between two of those valvular conduits ? Would superfluidity prevent the turbulence or not? Some one need to test this, cause we will soon realise Space might actually be superfluid ocean in wich planet floats. An article published on September 21st 2020 from Lancaster teach us object in superfluid helium act as thought they are in a vacuum.

[@vatsal9005]

Never thought Nicola Tesla would have had anything to do with fluid mechanics

[@Omgtired]

It is kinda common for genius scientist to work in various areas, it's just usually they impact certain field of study so much, that it overshadows their achievements in other fields, which are remarkable by themselves

[@snowblazed3442]

Electricity is kind of similar to fluid, except it's the electrons which are flowing instead of atoms.

[@srtghfnbfg]

@@snowblazed3442 i'm pretty sure you can't create a tesla valve equivalent with wires =v however i'm a software engineer so my knowledge in the matter might be limited

[@dtom2126]

Fluid and electricity both take the path of least resistance.

[@srtghfnbfg]

@@dtom2126 hmm so every secondary flow could be wires from a higher resistance than the ones used for the primary flow ? =o Now it actually seems plausible

[@JaredOwen]

Very cool! Thanks for sharing and great animation too

[@satyamwahi340]

Another great animator..

[@sierraapples8099]

Oh lol

[@nikoligogle3153]

I am a fan of yours too! 😀

[@cheesebusiness]

Are you going to make a video on how this valve is made?

[@Absurdi5t]

Why u are not getting a check mark

[@ohger1]

The interesting thing about this apparatus is that the reduced flow from the output side is fairly consistent no matter how much pressure is on the input side. It's not adjustable but this would have applications where someone would need a relatively stable volume of liquid flow regardless of the changing input pressure. I think that is the real purpose of this valve, not so much being a one way valve.

[@prjndigo]

its a solid state oscillating pump, remember he was working on pumps

[@oscarwoodly7392]

I wonder if there’s a lower threshold whereby if the input is slow enough, the various divergences and vortices are minimised, therefore the the output would be increased compared to if you had a higher input (which would seem to create more restrictive flow?)

[@VenhaVerIsto]

@@oscarwoodly7392 i was wondering the same, anyone got answers?

[@walterbrownstone8017]

There's probably a fairly linear relationship between input pressure and output volume.

[@ben3989]

I think you are right. It’s a simple and robust way to meter something using higher pressures elsewhere. It really can’t stop flow because it relies on the dynamics of flow to even work.

[@LetsPlayScience]

Superb Animation ! , i am big fan of Nikola Tesla😊🏆🏆🏆🏆🏆🏆🏆🏆🏆

[@kampungbumbu]

I was in the middle of nowhere and ended up here. Hence I watch this glorious video till end

[@rtlt2000]

Same here

[@whith5184]

I was watching a video about China. Suddenly, I was learning about the Tesla Valve. I feel smarter

[@DavideDeSilvestri]

Here I am too

[@makkashakka]

@@whith5184 I was watching a Japanese candy making video!

[@spontanious1072]

Same here

[@stevelangstroth5833]

"Tesla's valve is dangerous, immoral, illegal and nefarious!" ---- Thomas Edison

[@Hey_MikeZeroEcho22P]

" ... But ...WHY?? Is it because YOU didn't think of it??!!!!" - Nikola Tesla

[@stevelangstroth5833]

@@Hey_MikeZeroEcho22P "Heh, Nicky,....wanna work for me, instead of that Edison guy?" ---- George Westinghouse

[@Hey_MikeZeroEcho22P]

@@stevelangstroth5833 NICE! I wish I knew how to reply to that one!!! I'm assuming he that Tesla said, "no".

[@jasonterrell847]

Edison: I'll prove it by drowning an elephant with it.

[@blacksheep25251]

Went straight to comments looking for Edison to take credit for this...

[@arodmitton]

When you say "let's see it work" pretty sure everyone was expecting a real life version. You can make anything happen with computer animation

[@lick28]

Can you show the difference of water speed in a valve? It's an animation based on laws that are accepted. Like animating an object falling because we know gravity exists. Jesus

[@guywiththebottle]

@@lick28 His point was that you can animate anything. You can animate the valve breaking from excess pressure. You can animate an anvil falling on it. You can animate glitter coming out of the other end. You can also animate generally accepted "laws" in the logic of children's cartoons but that does not make them real nor evidence of any kind of "laws". And yes, you can show the difference of water speed in a valve. Today we have plastics and glass to make small scale low pressure valves. We also 3D printers and pressure gauges. I am surprised that a reasonable person would suggest that the only way to demonstrate how a valve works would be through computer animations. Because we all know the significance of computer animations when Nikola Tesla made the valve in question...

[@lick28]

@@guywiththebottle and my point is that there's no reason to make up anything false. It's also much easier to just animate something we know to be the effect of a certain action than to go out of our way to waste physical resources like water and money. It's also easier to articulate how the inner workings of something goes in an animation as you can highlight the important things to be noted. Complaining about the fact that it's animated in this context seems very nitpicky

[@guywiththebottle]

@@lick28 There is reason to make up something false if you can get away with it or do not know better. People care about 'fake news' more than ever and everybody is the publisher on youtube. The guy asked for another reason to believe the premise of the video. If people know the effect of "a certain action", there wouldn't be a point to making the video. Is it a waste of physical resources to teach people about valves? You can highlight whatever you want in an animation, that was the point of the critique. Not sure why it would be nitpicky that the guy expresses that he would be more convinced by a recording of a stream of water rather than a simulation of a stream of water.

[@neavo8421]

@@lick28 We live in 2022 and you really wanna say theres no reason to make up anything false? The dudes right, I wanted to see it for real. I dont want what he thinks will happen in an animation, I wanna see what does happen in reality.

[@beningram1811]

Something not mentioned in this video is that alongside the mentioned flow restrictions of the Tesla valve, after the first switchback the "main" flow will be directed towards the next switchback each time. It doesn't appear to be an even split into primary and secondary.

[@paratrooperboys1692]

TESLA: I used the pressure to destroy the pressure.

[@elephantgrass631]

He used the pressure of the pressure to pressure the pressure of the pressure.

[@pikachu-jf2oh]

He pressurised the pressure to make a big pressure which gives pressure to the pressure which gives enough pressure to crush anything but P R E S S U R E

[@elephantgrass631]

@@pikachu-jf2oh kzbin.info/www/bejne/l2GUgoSQrtFglas

[@pikachu-jf2oh]

@@elephantgrass631 kzbin.info/www/bejne/n6bEn4SwqrupjZI

[@elephantgrass631]

@@pikachu-jf2oh kzbin.info/www/bejne/p2qlpYx7o9eenZY

[@georgefan2977]

Also the primary flow in tesla valve isn’t a straight line. For every section of the “bucket” structure the primary path is tilted so that it matches the entrance of the next bucket structure, so making is very effective at dividing the primary flow into a secondary flow that opposes itself

[@puchookida]

So the answer to can you create a valve without a moving part question is NO. The Tesla valve increases the pressure drop in one direction so the flow will be reduce drastically but their will be a flow... It allows then a control of the flow rate not a perfect stop of it. You would not be able to use this valve instead of all the valve that you shown at the beginning of the video.

[@danieltakawi9919]

That's what he said at the end of the video, that there will still be flow so technically its not a non-return valve.

[@GummieI]

But at the start of the video (which is seen by way more people then the end (that is true for ANY video)), he heavily implied at least, that it was possible to make a actual one-way non-moving parts valve on par with the ones he showed with moving parts

[@XpVersusVista]

it still replaced the former valves in modern jet engines.

[@GummieI]

@Palo Kan Yes, because in such a place a total valve is not needed a flow decrease is enough. If the answer to the proposed question had actually been "yes" the only places the other valves would have stayed would be if there wouldn't have been enough room for the tesla valve, but as it turns out it only replaced the valves in a few places where a flow decrease is enough, the vast majority of tradition moving parts valves were not replaces because they need to shut the water completely

[@jack765ful]

@@GummieI I echo what you said, AND: “Replaced ___ valves in modern jet engines” implies the more traditional valves with moving parts were used in those sections of jet engine first. Show me. Were they? I have zero background in jet engine history or design. But I want to say NO, those traditional valves with moving parts were never used successfully in those sections of jet engine. So the “Tesla valve” replaced nothing in modern jet engine. “Found application in” and “Replaced” are two very different things.

[@groundchuck83]

As a 20 year master plumber I love the design due to it not having any mechanical parts that could fail for a pressure reducing valve this would be great

[@nischals510]

So this valve can only reduce pressure and not completely stop the flow of liquid. So complete stopping of water without moving parts still is impossible

[@killerdroid99]

As he said increase the patterns to increase resistance..... So , maybe add a loooong Tesla valve?

[@Fullyautomagic]

KILLER DROID it will never go to 0

[@johnny_eth]

> So complete stopping of water without moving parts still is impossible It is possible, use a gradient/slope.

[@natoisnazi]

Be a liquid my friend

[@akhileshravindranneena5600]

Just close the tap kid

[@laernulienlaernulienlaernu8953]

Fluid dynamics is a very interesting and very complex field and has an impact on so many day to day things that we take for granted. Tesla was a true engineering genius.

[@amzadansari4145]

hmmm

[@mikewhocheeseharry5292]

Like the valves and vessels of our blood.

[@mikekelly5869]

A visionary, certainly. A showman , definitely. A genius, I think not.

[@laernulienlaernulienlaernu8953]

@@mikekelly5869 I bet you are so much smarter than he ever was 😏

[@mikekelly5869]

@@laernulienlaernulienlaernu8953 That's a stupid comment. Tesla is a cult in the US and much of what's attributed to him is mythical. Whether or not I'm smarter than he was is irrelevant. The fact is that Tesla was a talented engineer but was not a physicist of any great ability. His achievements are greatly overstated and the hyperbole in this video is both incorrect and pathetic.

[@ObsessedCollector]

Imagine all the great things we woulda got earlier if it wasn't for the greed of Marconi, Edison and JP Morgan. Tesla was the greatest inventor ever!

[@tyriliusmc9798]

Capitalism will always stand in the way of humanity's progress.

[@Homeside301]

Because it was for the people, not for money.

[@lanhabanjanac294]

Exactly!

[@FaizanAmjad07]

Indeed, the greatest inventor

[@anothaeasywin]

@@tyriliusmc9798 you mean white people

[@thabangmashabela6837]

This was the pick of lesics, our brains were thinking of engineering. 😢Gonna forever miss this period

[@RandomYT05_01]

That man was a genius for creating things that are even used today.

[@rohanreji5440]

Like light bulb

[@RandomYT05_01]

@@rohanreji5440 that was Edison.

[@iwonaszaasny7954]

Yes, like an alternating current, which revolusionized electricity in our world and more inventions through it. I admire this person, it's amazing what he did.

[@Sarutulf_Lertimud]

@@RandomYT05_01 Edison did not invent the lightbulb, he just improved in it.And it is possible even that was not his own work.

[@FrancesFarmer00]

tesla was working under edison. edison told tesla that he will give him 1000$ if he can improve the running time of a lightbulb to 10mins. Tesla improved the running time to a time where the lifespan couldnt be tested in a few days. when he wanted to receive his 1000$ edison basically told him to fuck off. after this tesla left the company. so tesla only improved the lightbulb but from a few seconds to a time that made them usable even 100 years later. thats also why the lightbulb is patented by edison, because he owned the researchcompany

[@Tiriris]

Well I'm suprised the video does not show an actual water test.

[@david203]

Yes, showing actual fluidic components and models would be helpful for understanding. Notice the pulsing, as this is not only a partial diode but a partial fluidic oscillator.

[@inthemaze7441]

May be they don't have a wood or metal worker? Animations worked well enough as even if you could see though a plexiglass face, due to the valve slowing the flow, you could not see the direction of the water flow. This would then need animations of arrows again. What I would find interesting is more mathematical information. How long, at what diameter, fin size, and liquid pressure going into.

[@davilathegreat]

That would substantially increase production costs. You might be able to get someone like William Osman to do a video fabricating and testing a Tesla valve.

[@Tiriris]

@@davilathegreat not really. A cnc can cut out one for very cheap, and would have elevated the video above ufo sightings videos. You know, animations are costy as well.

[@davilathegreat]

@@Tiriris They are obviously working from an animation studio. It might be cheap for youtubers who perform on-screen, but that requires a whole new set of equipment and staff.

[@GEEK368]

That was really nice, please show more of tesla inventions

[@UkuleleBoy46]

A very helpful video! Thank you for explaining this.

[@solapowsj25]

The teaching method is excellent. Tesla valve is remarkable.

[@HAL-dm1eh]

One of the very best demonstrations I've ever seen on KZbin, and short and sweet just enough for my attention span.

[@casher7821]

Actual conversation with my wife: What are you watching? Something about valves Why? I don’t really know but I want to know how it works What it’s for? I don’t even know. But I feel like I’ll know everything about valves soon.

[@lillyanneserrelio2187]

Agreed. I was surprised by the 4k+ dislikes. Perhaps it was from people unable to understand the video... or maybe they are just Edison fanboys 😜

[@sircrapalot9954]

Claiming to be a “total physics” video without demonstrating a real world model of such a simple device is a fail. The simulation software is fine but not a complete picture. Also this valve is crap under any appreciable pressure. You’d get backflow in no time. It demonstrates that it is not possible to make a true check valve without moving parts. A small ball check valve easily handles the job.

[@solapowsj25]

@@sircrapalot9954 Application of newer technology is much needed. A train 🚂🚋🚃🚋🚃🚋🚃in a tunnel with walls that reflect the divergent air on to the rear of the train would have twice the efficiency of trains today. Using turbo jets to clear air from the front would prevent wind resistance in the tunnel while additional forward thrust is developed. Directing this displaced jet of air on to a modified Tesla mechanism on the tunnel walls to redirect the air jet on to the rear of the train would again add forward thrust. This is significant since wind resistance at 100 mph is equal to the weight force of the average vehicle. Also, the hyperloop intended to remove air resistance by creating partial vacuum in a tube is more dangerous than the Titanic. Lastly, Tesla has been successfully tested in jet and rocket propulsion. It's a topic to be studied by all engineers in this field. 🚴三 happy traveling.

[@xjet]

I have never seen an actual *working* pulsejet engine using the Tesla valve. The reason for this is that the valve is too "soft" and absorbs a lot of gas before it is "full" and the choking effect becomes pronounced enough to cause compression in the combustion chamber. For that reason, any engine built with such a valve would be unlikely to run well -- if at all.

[@s.s9397]

kzbin.info/www/bejne/o3ScYql7gtykY6c

[@abhishekgerald9774]

Completely agree

[@melonlord1414]

Do you encounter pulsejet engines often? I know the theory, but I never saw one in person...

[@xjet]

@@melonlord1414 I have built a *lot* of pulsejets. I was in an episode of Scrapheap Challenge and also technical advisor to Junkyard Megawars on their pulsjet drag-boat build.

[@lylestavast7652]

could this be adapted for use in "silencer" tubes used to dampen firearm discharges ?

[@derekc4919]

Big brain takeaway: Tesla Valve is not a check/one way valve, it is a regulator. Edited

[@Drottninggatan2017]

Yes. There are no moving parts he said, but you have to turn the whole thing around for to make it work.

[@frederikmoeller88]

@@Drottninggatan2017 Ridiculous right

[@greenhatzelda8273]

@@Drottninggatan2017 I think not exactly... the Tesla's Regulator works the same way as an one-way valve, but instead of completely blocking the current, it supresses its flow. In the example of the video, the mecanism just had to be turned around because there was only one current to flow through it.

[@Sejiko]

So basically a diode?

[@Jupiter__001_]

@@Drottninggatan2017 Just like any other one way valve, the purpose is to restrict fluid to only travelling in one direction, and not the other. Your comment is meaningless.

[@nicholasadams2374]

Tesla might be the most underappreciated engineer of all time. Alan Turing aka "The Father of the Computer" is another, albeit a computer scientist. Any video that celebrates visionaries is a plus in my book. Thanks Sabin!

[@apokalypthoapokalypsys9573]

I'm pretty sure Neumann János is the "Father of the Computer". No, I won't be calling him "John".

[@tomtomblos2909]

EINSTEIN is most overappreciated .... he never invent anything ... only theory that not proven yet

[@keithperdue4993]

I enjoy watching this every so often & it always blows me away how Tesla could think. Whudda guy!

[@darreno]

Whudda man whudda man whudda man whadda mighty gooood mannn

[@claudevieaul1465]

I'm guessing the main reason this type valve hasn't caught on is simply because, as stated, it can not complete block the reverse flow. For instance water without a lot of pressure behind it (from static height or a pump) will create less vortices and therefor less resistance. The harder you push the water through (use a big pump), the pressure loss will increase exponentially, and so in relative terms it will be more efficient. It still won't stop flow completely though. It will also mean more damage to the valve due to pit corrosion (the same you get on ships propellers), and that would severely restrict the lifespan. But it is certainly an ingenious design, no doubt.

[@Roatmeal]

That’s not necessarily a bad thing. When you have low flow and low pressure, the moving parts associated with a true one-way valve will be less likely to fail and will have less associated wear.

[@eryck123]

You can put a mechanical vale at the end which will be suspectible to less wear and tear.

[@CCNightcore]

Still useful 5:30

[@zarthemad8386]

Tesla's "valve" is a piece of junk. its only directional orrifice that restricts one side more than the other. It has no practical use. If you needed a 1 way orrifice... check valves and a spillback loop would be cheaper than manufacturing this POS

[@PtotheMtotheK]

@@zarthemad8386 - What a true simpleton you are. You really tried to speak poorly of Tesla's work? Slap some sense into yourself, boy.

[@rochditidjani]

I never heard of it (Tesla valve). However, I am stunned at the way it works. Thanks for sharing.

[@dannyredcdsdunn6634]

taking it step by step was very helpful, thanks

[@matthewhendy5785]

Tesla was a true genius. His ideas were so simple and beautiful.

[@bodyofalegend]

👍

[@anom3778]

Breaking news.. tesla was a ingenious

[@vickprakash8247]

Personally, I wouldn’t say his ideas were simple as what he provided to the world with Alternating Current is still quite complex to the average individual. When you dive deep into his research and inventions, it’s downright remarkable. For the average individual, it’s just turn a light switch on or turn the tv on and it works.....but in reality with frequencies, potential differences, step up or step down transformers, AC motor and generators and the Battle of Currents, he changed the livelihood of the entire world and died penniless and infamous.

[@Karuiko]

So basically more a resistor than a one-way valve. Still has its uses though. Edit: More like a zener diode

[@s.s9397]

kzbin.info/www/bejne/o3ScYql7gtykY6c

[@csnider_1281]

Like a zener diode

[@TyrDrum]

Pretty much.

[@faizanchunawala8407]

No

[@mihaigrigoras7956]

Yeah, also thought this isn't really a valve but more of a flow regulator.

[@osagetorch8045]

So he created a one way valve that doesn’t stop water one way just “drastically reduces its flow”, brilliant!

[@andrequimpo9363]

And what have you done?

[@timprescott4634]

@@andrequimpo9363 What a ridiculous statement.

[@palodoxaliqua5809]

@@timprescott4634 No, he pointed out that the critique is ridiculous, because completely stopping the flow is not what this invention is about. Knowing the most efficient way to reduce flow rate is in many cases exactly what's needed. Also with enough loops you can get a almost coplete seal. Not having 100% efficiency does not reduce the usefullness of this invention.

[@timprescott4634]

@@palodoxaliqua5809 No, he didn’t. Had he done that I wouldn’t have said anything. He just punted to the intellectually bankrupt, “What have YOU done” reply which is RIDICULOUS.

[@andrequimpo9363]

@@timprescott4634 really? My reply is more ridiculous than the one who sarcastically said the invention just reduced the flow is brilliant?

[@THC800]

I wonder if the Tesla valve can be used as a muffler or a silencer to minimize sound wave travel…

[@thedanwin]

It can but it's not as well since water and sound are way too different. Sounds can go through objects as well while water can't. That's why there are specific materials used to lower sounds such as foam.

[@jctroutt]

It would be more accurate to compare this to a pressure-reducing valve, rather than a check-valve / back flow preventer.

[@AnujFalcon]

Yep.

[@TopLevelJiuJitsu]

Was thinking the same.

[@byronndavis1074]

I would love to see you do it. Just think of what would be accomplished and designed by you.

[@titirititiri6360]

@@byronndavis1074 I would redirect the fluid all back to the original source mono directionally, this would be equal pressure in opposite direction of original flow, they would cancel each other out

[@TomorrowisYesterday]

That’s what I was thinking. For a sump pump check valve. Only problem is those are supposed to be vertically integrated. But I would imagine that the sound of it turning off would be drastically reduced if you put a couple 90 degree elbows just above the pump. It would of course need a traditional shut off valve below it though. I mean even the more expensive “quiet” is by no means quiet. And they break, too.

[@robertgiroux9891]

When you look at his achievements inventions and abilities, stacked against any other man throughout the entirety of humanity, that we know of, Nikolai Tesla is by far the number one greatest mine.

[@techytech1907]

You may want to look up Leonardo Devinci life’s work. Now that’s a dude that takes the title of the most successful human being within our species.

[@eduardogaxiola3907]

Let’s not forget about Newton. That man defined our current understanding of classic mechanics and created amazing mathematical tools that help the ordinary man to reach the extraordinary (calculus)

[@godzilla362]

@@techytech1907 seriously. A hippy is being compared to actual scientists 😒 Y'all are goin to hell.

[@justincameron9123]

@@godzilla362 Did you just call Leonardo da Vinci a hippy

[@somuchsoul3041]

@@godzilla362 what? Do you know who Leonardo Devinci is?

[@UDEMF]

Yes, after 18 times recommended I finally watched it. Great mind of Tesla, ill make one to use on my money flow :o

[@armando1is1great]

2:40 the two hoses' streams colliding made me laugh so hard for some reason. Great vid and explanation

[@fpvflyer4758]

2:24 Guy: “You guessed it!” Me: What the heck are you talking about?

[@abibnoor]

😂😂😂😂😂😂😂😂😂😂 I swear I had the same concern.

[@-weaponized6493]

Its like Dora the Explorer asking you if you see some abstract concept and needs you to click on it.

[@taxxddlleetadpoleelletpoac7622]

@@-weaponized6493 it all seems so USEHOWNOWFULL... (Starchildtroo) per? WOODULIIK2KNOMOREEESSSSSPLZ.

[@pjpdjs]

Yes, I was thinking the opposite effect would occur.

[@irjan]

It is just like asking a dog if it believes the universe is deterministic, and then shout out "You guessed it, good boy!"

[@TracyA123]

Everytime I think Tesla can't impress me more I see something like this. That man was just incredible.

[@Darxide23]

He was also sexually attracted to pigeons. The more you know. :)

[@TracyA123]

@@Darxide23 Tbh I've seen some pretty hot pigeons myself and I can understand the compulsion.

[@cellulairerare]

@@TracyA123 what

[@TracyA123]

@@cellulairerare Yep! I've also seen a few really fine squirrels! They're too fast for me to catch though😞

[@NostalgicMem0ries]

@@TracyA123 lmao

[@moorelucas5441]

This is pretty amazing video on Tesla, very innovating, educating and inspiring, young lads should go into more of things to build a greater and invested future for themselves

[@millerrichard2014]

When bitcoin started it all started like a joke now the worth of it is mind blowing, those who took the wise step then never regretted it

[@mitchelleprime6490]

This crypto of a thing I've got interest in investing but afraid of doing it on my own to avoid loss from my own end 😕🥴, and also would love how to trade it too

[@wilsherefrank7554]

@@mitchelleprime6490 that's why you need the help of a professional who trade and understand the market more to earn good income.

[@wilsherefrank7554]

These professionals understand the markets like it's there own farm and makes maximum profits for investors.

[@bellamike5868]

I have been investing and doing it on my own but end up losing all. Just last week i lost $7,450🤨😮

[@MrJbt2112]

Thanks!

[@hayeopreis]

Seeing the nice graphics 0:27 the working is clear without any explanation.

[@AppallingScholar]

Not everyone has that intuition bud

[@explosivemallard8038]

r/iamverysmart

[@Wojtgaw]

After seeing this in my recommendations for the 1000th time, the time has come to watch it.

[@N0xiety]

Lol same

[@__shifty]

i was a plumber for years. this valve is a joke. it cannot do what's advertised. want proof? go ahead and try to find a video of this valve in operation. the water shoots out either side just as fast as you pump it in the opposite.

[@N0xiety]

@@__shifty You know when this valve could work? Lets say you have a junction with one side a normal pipe, and the other with this valve, the water will obviously choose the way with the less resistance. If you somehow had a pipe blockage or an overflow in the other pipe, the water will then be forced to move into the valve. This is a scenario i think it would do a good job at. It is not a valve that can stop water when you force into it. It can only be a resistive valve.

[@Ramingo1983]

You acted like the Tesla valve, much resistance but in the end you've watched it.

[@AM-te1ff]

😂😂😂

[@johnny_eth]

I would have loved to see a real demo with a colored liquid.

[@BGraves]

It doesn't work. Someone already tested it

[@e.c.listening326]

Stella smith „colored liquids matter“

[@marcograsso1386]

@@BGraves i think is used on steady flow irrigation system, if you open a dripper with fixed flow rate you see something like this.

[@revimfadli4666]

@@BGraves who tested it? Tim from Grand Illusions tested it and it worked

[@MM-rr1kp]

@ #CLLM

[@screwsnutsandbolts]

Excellent video ! 👍

[@Idontknow-xy7bc]

2:25 “you guessed it” No I really didn’t, I’m not even sure why I’m here

[@myhanslombard]

lmao

[@jennyanydots7582]

Yeah, me too. I fell into a wormhole and now I’m in Tesla’s mind 🤪

[@smileycacho2936]

Hahahah yea2x

[@domtron8873]

Cliche television

[@ProfessorGroyper]

Frank Stallone

[@landoragan4894]

Truly an under appreciated genius mind of science was Mr.Tesla. There’s been none like him since.

[@AZCobraman]

Except the guys that invented the transistor, the laser, the microchip, split the atom....

[@adamwal4591]

Tesla was not a scientist and performed zero research.

[@titanusgojira8875]

Water: flowing peacefully.. Tesla: No..we don't do that here..

[@jsing_races_everything]

Out of all the subjects in school physics is the only one that makes complete sense to me

[@XpVersusVista]

You guys forgot to mention another genius effect of this valve, which is the reason why it isn't near 180° (for example 178°): when the flow of one secondary stream mixes with the main stream, it doesnt just slow the mainstream down, it redirects its forces into the following secondary stream, since the secondary flow comes in at an angle instead of (near-)directly from the opposite side. Thus the force in the following secondary valve is increased, helping it to slow down the main stream even more.

[@oscarsilver3773]

I was waiting the entire video for them to mention that 😁

[@mirceastaicu4131]

One thing that would be worth mentioning is that Tesla's design relies a lot on Bernoulli's principle. The trade off, in this application, is between pressure and speed. The speed is determined by the Coandă effect. According to the definition, if a fluid meets a curved surface, in our case the added obstructions, it will attempt to follow it. When this happens, the fluid that needs to travel further on the encountered obstruction will speed up (and drop in pressure), resulting in a higher velocity, which will result in the diverging stream clashing with the main stream, obstructing it

[@stevealaska73]

Precisely! ....( I had no idea )

[@feizal7554]

true... they use examples to be in line with their theory.. which is incorrect

[@mirceastaicu4131]

@@feizal7554 Can you share with us a link to a resource that outlines the correct theory? I'm sure a lot of people will be curious about it

[@jamesalonzo6207]

Yes, and the design also has similar affects as Archimedes describes with pulleys. But most importantly it all ties into the theroy of relativity and how we are moving thru spac and time. I think

[@786ALHAQ]

@@mirceastaicu4131 There is no "correct theory", it is simply a theory, not having all the datum of each subsequent obstruction and / or separation of the fluids. Basics in physic... the more obstructions in the flow path, the lower the ve locity of the flow and the increase in the pressure, if there is a constant force applied to cause the flow i nt the fiorst place

[@johndii2194]

Is it possible to design a one way valve with no moving parts? 0:02 So the answer is no?

[@chriso1373]

Well if you consider that its technically a throttle valve, and not a cutoff valve, then id say yes, yes you can.

[@southtonorth-original]

@@chriso1373 NRV

[@Josh729J]

@@chriso1373 if it was larger and the pressure not too high and it was stood upright so gravity helps maybe it would work

[@bmxscape]

@@chriso1373 a throttle valve except you have to take the whole valve out and flip it around to get out of idle

[@chriso1373]

@@bmxscape throttle isnt just a car term buddy. However you can easily reverse the flow with clever use of plumbing and cutoff valves

[@lo-tar1442]

I love it! Tesla basically created a Diode which is an electrical component on circuit boards which will only let current flow in one direction - except he created the "Fluid" version of a diode. Which is awesome. I just watched the tesla turbine video and it seems he was doing what we do today just with fluid instead of pure electricity.

[@cornman1123]

Dammit you said it first

[@EricLeafericson]

Oh that a cool way of thinking about it! It's a water diode, that makes a lot of sense. Great comment.

[@tasost]

What a genius Tesla was. And the system obliterate him because he was not 'cooperating'

[@joshuachandy8060]

@tasos t , you seem enlightened my friend.

[@harrisonwells4600]

O really did the system eliminated him.

[@zilchbupkis3109]

@@joshuachandy8060 haha he really does doesn’t he hahaa

[@SKITCORP]

Tesla had connections with aliens...or future us...

[@michaelmccullough458]

@@harrisonwells4600 nah nigga, he was part of the system n they where like "wtf you trying to do kill us all? We biding time here tell the next cyclic disaster." I'm white btw... I got my black card lol.

[@userasdf1546]

I don't know why I'm watching this, I don't even fluid engineer

[@bitchplease1114]

Zheka K how much watch?

[@botlarry4437]

It never hurts to learn

[@dannyyo7948]

well you can become one!! good luck!

[@stukagamerxtreme]

Anything with Tesla's name on it aells

[@warpspeed8305]

Procrastination

[@harshahk3639]

The first sentence of video has to be like, “The Tesla valve cannot block the flow completely”

@Ronin yes, there are 100% in the real world with valves, they will stop the flow of water.

[@MGZetta]

@Ronin In real world, your sink never closes? Lmao.

[@JSpradley123]

Stella smith almost all valves leak. Bubble tight valves exists but they are $$$$$

[@Robbedem]

@@JSpradley123 I think you underestimate available valves. We have 100'es of valves at the factory and they all seal fluids 100% at pressures under 5 bar. (different story for gases or fluids under high pressure) The only real maintenance is replacing the rubber seals once every couple of years (depending on the usage)

[@roomtemp6374]

It's not designed to be a constant pressure valve. Under pulsing conditions, and with the right size/length conduits for the density of the fluid and pulse width, it effectively does block flow completely. Think reed valve, not water faucet.

[@Tod_x]

We should support this channel, not those immature challenge video

[@raziel33581]

These principles also apply to the human cardiovascular system.

[@TheLocoRunner]

Incredible. I'm going to research that. I'm guessing that the tubes get increasingly smaller?

[@sonalipatil1278]

Exactly that's what I was thinking

[@dizmatt1]

I didn't realise this, I thought that recirculation was best avoided in the cardiovascular system and that the venus system has moving valves. also the elastic properties of the arterial wall help propel blood through the system. Venus flow is dependent partly upon muscular compression of the venous system and valves. Recirculation is massively avoided in the arterial and venous system such as the Miller Cuff using during femoral artery bypass (if I recall correctly) and in arterial aneurysms, recirculation and stagnation cause sclerotic build-up and eventually stresses that cause rupture.

[@thorandlundeve]

Actually our heart have moving part. It's not rigid

[@Kurogane-el2vq]

I only noticed until you mentioned it 😳

[@KevinATJumpWorks]

One additional perspective: Tesla thought in oscillations and capacity - As demonstrated in his work on alternating current. While this valve works for steady-stream applications (like constant pressure water flow), it is intended for oscillating flow (like in the pulsejet engine).

[@dakilakilada3053]

what i am doing here 2am reading comments, guess anything from NTesla is interesting :)

[@wastedwizard5112]

Aye, constant flow isn't impeded by the valve nearly as well as pulses. It's very clear this was made to catch bursts of pressure 👌🏻

[@xerxis301]

@@wastedwizard5112 I don't think so.

[@Robert_McGarry_Poems]

Tesla was intrigued by the idea that vibrations, so basically sound, had the capacity to mimic other chemical and physical reactions. Modern science now calls this study phonons. Later, he would update his ideas to include sonic resonances from many different phenomenon. This obviously influenced his work on radio and alternating current. And directed his ideas later in life about wireless electricity, through microwave transmission. He probably didn't have an understanding of microwaves yet, but that is what he was thinking about.

[@davidbaker9089]

I’m sure had Tesla directed more time and contemplation towards this valve , he would have incorporated a full stop application. But to serve as an indication of the type of mind Tesla possessed, he was at least as brilliant as Edison, if not more, and fit to sit at the table with Einstein

[@EmoFox9]

I'm s ok annoyed that this is just animation and nothing done in real world testing

[@jocerv43]

Huh, I was more pleased to see it animated. Mostly because it's explained clearly. But I wouldn't have minded seeing it in action.

[@desertbrewcrew1974]

Yup. Actually, at the 5:10 mark, the pressure reading on the pressure or inlet side should spike up to whatever max pressure is sending it, NOT remain the same.

[@Pjc05002]

Maybe you should make a video? Obviously you'd be the superior channel. Leaving money on the table if you don't 😅

[@mvn4844]

well thats simple, it doesnt actually work in real life aplications,, just try switching this valve for youre one way valve in your hydraulic or pneumatic system and you will see that there is pressure arriving at the end, if there is flow sure it would be restricted and not be as high as without the valve but the point of one way valves is that there should not be any flow in one direction and this just simply isnt possible with this valve otherwise you can bet on it being used in real world aplications

[@arshawitoelar7675]

I think veritasium did a video on this topic, which includes real world testing.

[@mohamedzakriaellgarib6240]

Video is more than wonderful Keep it up I want more innovative hydraulic ideas

[@nickputkaradze1181]

Basically, it's a diode. Can't wait to see fluid transistors

[@BlueberryCats_]

Didn’t someone make a liquid calculator? If so it shouldn’t be *that* hard to make one

[@JassZoigel]

@@BlueberryCats_ the amount of work to get 4+3is astounding

[@nandechi7563]

Its rather a resistor

[@Robert_McGarry_Poems]

@@nandechi7563 Transit one way/resist the other, transistor. Resist both ways resistor.

[@sumitmishra3037]

Lero lero lero lero

[@kristianspot2683]

The animations are insanely good

[@CLINT_theNotorious_TTG]

That’s more like a pressure regulator than a stop valve. Still very cleaver though! 💡🤓

[@garyheaton4791]

That is EXACTLY what I came away with. It would slow the water by a great deal..but it couldn't stop it. Not without a shutoff VALVE to do so. I guess I am to stupid to understand what they mean by the word..VALVE. 😂😂😂😂✌️

[@bradhardy100]

Some folk need to look in a dictionary

[@OttoByOgraffey]

@@garyheaton4791 *too. *too stupid. LOL!🤪

[@michaelmccullough458]

@@garyheaton4791 hello binary friend, put the unit at an angle n u can stop the drip. Stop acting so linear .

[@luiexluie]

No, not a pressure regulator but a flow regulator. Like in drip irrigation. I do wonder how the flow reacts to an increase in a higher or lower pressure.

[@RomanZerstoren]

This video reminds me of another old-school video about car differential. Another masterpiece.

[@terryspence7609]

As a "flying/physics" guy I see the airfoils everywhere, but what I think is genius is finding uses for the trickle leak. Bravo!

[@raintoshine2604]

I don't think it's possible to understand how Tesla's mind actually worked.

[@JensHove]

He fell in love with a pigeon, so there were a few nooks and crannies in there.

[@joyroy366]

@@JensHove tf

[@lolrekt6269]

Push the water back with water? Its really simple if you think about it

[@Ok-zr6ev]

He is said to have been a schizophrenic

[@catmills22]

@@JensHove yeah, but you should've seen that pigeon!

[@hamsterdoom360]

Just when you think you know about all of Tesla's amazing accomplishments, you learn about another one.

[@igoranisimov6549]

Gee, do you call "amazing accomplishment" something that was never used in practical applications because it is not even effective?

[@roshasensi2220]

@@igoranisimov6549 wdym "never used"? at 5:43 he says "model valveless pulse jet engines use the tesla valve to replace the reed valve in conventional pulse jet engines"

[@igoranisimov6549]

@@roshasensi2220 or really? Do you mind telling which company makes them?

[@100100freak]

@@igoranisimov6549 oh shut up Igor

[@roshasensi2220]

@@igoranisimov6549 bruh he says model valveless pulse jet engines USE the TESLA VALVE to REPLACE conventional pulse jet engines that means they replace the reed valve for the tesla valve.

[@MechTechSimulations]

Awesome Explanation of the excellent concept. I'm interested in doing a CFD simulation of this valve after watching this video.

[@guyfeeyeti375]

Seeing the applications for this was mind-blowing. My jaw was hanging when you showed the pulse jet example.

[@GregMoress]

They should have called it the Tesla Jet Engine

[@namgoCS]

I was in the middle of studying and somehow ended up here

[@mattialandoni6944]

I'm in the middle of online classes and I'm somehow learning more by not listening to the teacher

[@kevinraymond4912]

@@mattialandoni6944 damn

[@codyism666]

KZbin is weird like that. Sometimes, if you keep going, you can find the bottom of the abyss inside the rabbit hole. Once you get to the bottom, you wont want to leave. Finding your way out of the rabbit hole under the merry go round, is a maze thats almost impossible to leave.

[@kevinraymond4912]

@@codyism666 well said

[@apolosilver2054]

Well, you're still studying.

[@aznpanda510x]

Such a shame that he die because other people want his work. Just imagine what he could’ve created

[@ac350nas]

He had no money :(

[@elbabydelflow4459]

@@ac350nas your right but con edison dint want to hire him instep he wanted to still all his plans because all Nicole created were better dam hiss

[@ac350nas]

@@elbabydelflow4459 you're right

[@ezekielnduli5181]

@@elbabydelflow4459 yeah. Tesla's greatness faced huge obstacles. People who cared more about themselves than the advancement of knowledge. We still have people like that today.

[@turdle69420]

@@ezekielnduli5181 this just in - he entirety of our history has been a struggle.

[@johns1625]

Has anyone ever tried to make a firearm silencer in the shape of a tesla valve? I'm interested to know how well it would work at slowing down gasses and whether the moving projectile blocking the primary flow channels would effect it as it travels down the valve. However my instincts are telling me the gasses would just push the projectile downward in the direction of each curve and it would probably just blow up lol.

[@testurenergy]

Yes there are couple patents on it actually.

[@artstudio9673]

As I was watching was thinking of asking same question. I think that it would be part of a good design but because gas can be compressed and fluid can't that not all of the same physics applies the same way.

[@spicycrabnoodle9049]

kzbin.info/www/bejne/jmPCeoJ3gtGErKc This is suppressor CAD design using tesla valve

[@czarekaj1098]

Nobody really knows how Nicolai Tesla mind worked. He was a genius.

[@lanhabanjanac294]

Absolutely agree!

[@wibes6043]

Its Nikola not Nicolai

[@apIthletIcc]

Makes you wonder if they had Tesla's works in mind when designing tire treads that push rain out from under the contact patch. Cuz I'm looking at the first set uof examples up to the 3 minute mark and can't help but see tire technology as well.

[@mateonicholls7875]

Just thinking outside the box, he is thinking about biology to make mechanics and fluids work. This structure looks exactly like a shoot system of a plant.

[@agustinvis5720]

Interesting. Well...he studied a lot a subjects.

[@suryanshsaini4784]

Yeah I noticed it too... These old school geniuses observed nature very precisely and they use to find solution to many problems in nature... Finally people in present era are starting to do the same & so Biomimcry is increasing now...

[@BGraves]

Too bad it doesn't work at all

[@shadowdance4666]

I also thought of biology

[@marsgo8938]

@@BGraves No offense but that's an oversimplification: "Granted, my understanding of physics and engineering is largely autodidactic and therefore incomplete, so this may be incorrect. Many of the arguments against this valve seem to be centered on the fact that it cannot 100% stop flow when fluid/gas is introduced from the restricted side (RS) while the unrestricted side (US) has no flow into it. For them, this means that the valve does not work. However, it seems to me that that is not the correct usage for a valve such as this. Rather, it is an effective way to show how flow within the valve works. Under working conditions, I believe the valve would work to prevent a complete flow reversal in a single-direction flow environment. Because of the design, reversed flow entering from the RS loses pressure as it moves through the valve, which allows the intended flow from the US to overpower the reversed flow and keep the larger system working correctly. In application, this would be useful for situations where backfire can occur, as it would largely prevent exhaust gasses from flowing backwards and reaching the combustion chamber prior to the valve. The lack of moving parts to prevent backfire means fewer places for mechanical failure and fewer necessary redundancies to prevent catastrophic failure. One-way valves also introduce a certain amount of drag/impedance into the system during normal operation and the Tesla valve appears to have a far lower amount of drag/impedance during normal operation, which may be another reason why it is being used in experiments in lieu of mechanical one-way valve." - fogotn 1 above this comment

[@Readioheed]

Yes, I am very awed by the man's genius!

[@JC-XL]

1:14 The 2 options shown actually have pretty similar resistance both ways. You say one is diverging and the other is converging, but that's not true! For example , the one you say has diverging flow (you're only looking at the increasing distance between the obstacles along the centre), but what about the obstacles converging toward the walls?!? Both options have converging and diverging areas and will have pretty much the same resistance either way. So these are not demonstrating what you're trying to prove.

[@randomgamerman4179]

I'm so glad I found your comment so I didn't have to write it myself

[@sotirissoyvleris6966]

the water gets in from the center this is the main flow see the video again with open mind and dont try to find the wrong its not there

[@Danon60Hz]

SOTIRIS SOYVLERIS Mate, you should use an ‘open mind’

[@sotirissoyvleris6966]

Ok whatever 😌

[@JC-XL]

@@sotirissoyvleris6966 Man, you can look at it with a mind as open as possible - philosophically, mathematically - but it is not possible to have a flow with one and the same repeating diverging section, without having a converging sections in between. Think about it. Imagine a diverging section where the flow starts with a section of 1 square inch and increases to 5 square inches. Then in order to start the next diverging section at 1 square inch again you have to converge your flow back into 1 sq inch, i.e. you'll need to converge the flow. It's just logic. I am not bashing on the tesla valve either. It relies on a different principle, it splits the flow and uses the kinetic energy of half the flow to reduce the kinetic energy of the other half, robbing the flow of its kinetic and respectively potential energy and significantly reducing it in one direction. It is designed for a very specific use - high velocity gas flows, or more specifically inlet valves for pulse jet engines.

[@boowonder888]

I just had to sub. Never heard of this before. So much stuff Tesls invented that is being used without us even knowing it.

[@gefiltafish2187]

One of the greatest minds to ever walked this earth. Just imagine what could he accomplish if he was living in our times

[@ashqelon7267]

actually he was NOT. There are designs and mechanics that far exceed anything he produced various compelling theologies, and physics. like the canaanites that learned to move 2000 TONNE solid rocks stones from quarries. Other created intricate precisely tunes musical instruments 4-6 thou[sand years ago, great furnaces with grape juice & copper vats making HEAT TO furnace and produce metal swords. ETC.

[@mVpkilla93]

@@ashqelon7267 wtf are you talking about ? Where are your sources on this ?

[@garrettg5130]

@@ashqelon7267 I think one big flaw in that logic is that the inventions you reference were likely the life's work (or multiple life's work) of whoever invented them. Whereas Tesla created this as well as hundreds of other history changing inventions/concepts (mostly in electronics). I get it, people seem to worship Tesla. But, just because he might be over-hyped doesn't mean he wasn't a formidable genious.

[@devilbowser253]

Every once and a while youtube brings us all to an interesting video like this and we all learn something new

[@rudolphleroux47]

Under steady state conditions this valve will only yield a constant pressure drop without any further control to the pressure or flow. It looks intriguing but it is just one design for breaking a fluid during its flow pattern. Valves like these are actually horizontal orifices much like vertical orifice used in pitot tubes to measure pressure differentials. The real benefit to control would be if the directing vane angles could be altered through another mechanism to then alter the flow and pressure gradient through each subsequent units.

[@prasadjonnalagedda8633]

once we introduce moving parts, the basic spirit of the invention may get effected. i am wondering about additional units arranged in a pattern, some how creating a fluid transistor/ diode kind of circuits.

[@amadeuszw5929]

I would call it more an anti-return valve than a classic valve, mostly because if you want to stop the directed flow...u have to move something anyway. Besides that - very interesting piece of material :)

[@goodcitizen3780]

It's not meant to be a shut off valve, just a one way valve to prevent contaminates from entering the source. We call them check valves. We use them in almost every building and system that uses water. Here Tesla created the same effect in a more efficient way, without moving parts, by creating pressure differentials. In the little clip where water is flowing into the black pan, contaminates would not be able to enter supply tank because of the resistance offered by the device in combination with the positive pressure from the supply. It works as well with airflow which is why it is seen here being used in the jet propulsion application. The positive pressure from the engine and the increased resistance at the prevent backflow of fresh air. I hope this clears up the type of valve and some basic applications for it and, most importantly, why.

[@shredBucketheadshred]

@@goodcitizen3780 exactly, to prevent reversion

[@davesmith3289]

@dude man but bit doesn't even do that in real life, it only works in cartoons.

[@zach11241]

The more I learn about Tesla, the more I realize just how much our world loss with his passing. He was born in a time that could appreciate him but that could not fully utilize him.

[@johntiggleman4686]

And he died basically penniless. Sad.

[@solosailorsv8065]

Died unsung because he wouldn't develop a Rail Gun for the Gov. Good Man

[@aguyfromnothere]

GIven most meaningful discoveries are simultaneously discovered it is unlikely any one person makes much difference in the overall accumulation of knowledge. It is sad we loss Tesla but we likely lost no scientific progress.

[@HELLios6]

@@aguyfromnothere Untrue statement.

[@steeledminer616]

@@aguyfromnothere Electronics as we know them wouldn't be the same if we didn't have him so I don't think this is a true statement at all. Edison had already pushed for his own style of electronics, the only reason they were changed were that Tesla challenged it. Tesla was very unique in how fast he could test stuff, without any resources at that. He could come up with a nearly flawless theory on thought projects alone.

[@ghost_kitsune]

Dunno why dunno how but this is on my recommended, and I’m not mad about it

[@MrTemplerage]

The brilliance of simplicity!

[@Prosti_bro]

Зачем я это смотрю в 12 ночи?)))

[@mrsmglp]

Самое странное в том, почему мы это видим в рекомендациях

[@Prosti_bro]

@@mrsmglp полностью согласен )

[@РусланГалеев-ю2ж]

Я думал я один такой. 😂🤦‍♂️

[@ИванПетров-о7й7о]

Знать бы ещё чё он там шесть минут гундосил.

[@ifeellikeiwasborntoloveya6547]

im watching at 6 in the morning and havent sleptz

[@gilmartrevisan]

I would like to see a real experiment.

[@jerrylopez03]

kzbin.info/www/bejne/qpS5YniPiLqEg6c

[@djinn666]

@@jerrylopez03 The flame went out the other side pretty quickly. Like in a blink of an eye.

[@imgonnafindyourfamily3364]

Or fluid simulation at least

[@davidjones-vx9ju]

@@jerrylopez03 that is not a real experiment

[@taerog]

There are a few on youtube. But rém this was designed for fast moving gases not liquids. It's not a valve. And only restricts opposite flow (does not stop it) Also the original design does not work extremely well. Later designs work much better.

[@Woodys_Hobbies]

Informative thanks!!!

[@everydayhero5076]

I am amazed and surprised by Tesla at every turn. What a genius, Edison and Co. should be ashamed.

[@prasetyomardi1723]

Edison was a greedy man,didn't anyone become better than him

[@bobbg9041]

TESLY was mad insane. But he also looked at the world differently then most people do i belive he had dyslexia. So did Eddison. Being able to look at somthing with a fresh perspective and ignore others belief in limits your open to try somthing not looked at before becuse once someone figured somthing out they stoped looking thinking it was the best and only way. But if you think about it the old saying is " more then one way to skin a cat" you just can't use the same old kitty. And you think thd mouse was scared.

[@Matu1]

@levi blankenship Current kills, it doesnt matter if its alternative or direct.

[@ashxxiv]

@levi blankenship lmao

[@everydayhero5076]

@levi blankenship It already is in your house genius.

[@Noahfence251]

I have to admit I'm a little confused on the converging & diverging flows. Maybe I'm not thinking of pressure relative to the explanation, but wouldn't the pressure be reduced in the diverging model?

[@gkooistra91]

The dynamic pressure will decrease but the static pressure will increase. Slowing down a flow will increase static pressure and decrease its dynamic pressure.

[@тралльилитный-ь7я]

For whatever reason pressure decreases when a substance moves faster, that's how planes work. Don't question it

[@blackbomber72]

@@тралльилитный-ь7я the energy of the flow is divided in kinetic energy, gravitational potential (which for this discussion we can eliminate by placing the tube horizontally) and pressure internal energy. Whenever you lower kinetic energy by slowing down a flow, you raise either potential or pressure, if a tube is horizontal potential can't change, so pressure rises.

[@paulinotou]

I think it works like a water gun when pressure is pushing into a smaller, the pressure in the liquid increases. Thats how a lot of pumps create hydraulic pressure. But I'm not really well read in engineering.

[@brick3827]

Pressure = Force/Area Therefore, a decrease in area with the same amount of force will produce a higher pressure. I have no idea what this vedio is on about

[@broski365]

Just call it "its so inefficient, that it almost blocks it"

[@BlacksmithTWD]

Making it a flow reductor rather than a valve.

[@tomcurtis3149]

@@BlacksmithTWD agree, its not a value, its not able to block the fluid completely, its more like a diode in electronic

[@satyakisil9711]

@@tomcurtis3149 It does actually feel like a Diode with biased electron flow.

[@HPD1171]

@@tomcurtis3149 or a diode with a parallel resistor since a PN junction on its own is very good at blocking reverse current which is the purpose of having them.

[@wolfpack4128]

It's honestly more useful being used in reverse. There's really no reason to use it going the higher flow direction. This technology leveled a many British buildings.

[@Malahovka777]

Very beautiful, you are just great and thank you for the beautiful videos!!! Samchenko Gennadii !

[@isuru3945]

The greatest mind mankind ever had!

[@darthnosam3313]

I believe Einstein even agrees with you!

[@kregadeth5562]

The democrats would credit Nancy pelosi with that title

[@seekter-kafa]

i think it will be hundreds (if not thousands) of years until a mind like that shows again

[@hectichive889]

@@kregadeth5562 Well here comes that one guy haha

[@hrdrr860]

Why is a republican on this educational video? usually they are not that bright...

[@lordraj365]

Cant believe how his mind was capable of thinking like this. What a genius!

[@russelltalker]

It's really not that incredible. I can't understand how a person couldn't come up with this if you were specifically looking for a one way valve with no moving parts. The first image that enters the mind is surfaces or mechanisms which grip or engage in one direction. Like a ratchet or running shoes. Then your brain combines those forms with a pipe. Then it see this would not work as is or at best provide very minimal extra resistance in one direction. Then your brain says, how can we increase the resistance? And it answers itself and says by creating a secondary flowpaths which apposes the primary.

[@guywiththebottle]

What really bothers me is that if somebody did something similar today, you wouldn't care. You care because Nikola Tesla did it. Because of his other inventions. You also care because somebody slapped the letters Tesla on a billion dollar company and now anything related is amazing. The guy asked himself how to restrict water flow. All you need is a material for water to run through and move things around until you are satisfied. Then, you show it to the public with little success because the market did not need the solution or your sales pitch was weak. Then, you die and wait until somebody makes a company with your name on it and an organisation decides to use a handful of valves using your design. That is how you make a Tesla valve. No advanced formulas, no string theories, just carve out some wood and drive some water through it. Alternatively, replace the wood with clay.

[@russelltalker]

@@guywiththebottle but I mean he was a genius and alsoal a successful. person. But I get you think he has become another hip geek fad

[@jjsc4396]

The counter-intuitive aspect is decreasing pressure during convergent flow. While velocity increases, one perceives that squeezing a flow into a smaller volume will increase pressure rather than decrease.

[@gerchwurzelsepp8243]

Can you explain in other words/examples why this happens? My mind has trouble dealing with this, and I had always thought the exact opposite. While not exactly important in my line of work, it sure can be embarrassing if I get this wrong on such a fundamental level, and I'll be teaching an apprentice soon, so help on this would be greatly appreciated.

[@sajadnaderi9456]

First of all, I wanted to thank you for your amazing animation video! It was truly fantastic, and I enjoyed it a lot. I was wondering how you made this video and what software you used? I’d love to learn more about your process.

[@billucf96]

Each of the little "islands" looks just like the cross-section of an airplane wing.

[@rod2d2rs]

Interesting observation

[@abam9787]

You're on to something, I can tell...

[@gregoryvschmidt]

billucf96 the Bernoulli principle at work

[@louf7178]

Interesting

[@hexturner143]

yes, bernoulli's principle

[@realoldbeardedguy]

Whilst being up...Googling.."Do penguins have knees.." I ended up here by a mistake (knocking my forehead into the keyboard I guess...Falling asleep!), hence being unable to answer that question, I'm totally unable to google it again... BUT, I now know how Tesla used pressure to kill pressure...Thanks!!

[@SwervyMack]

lmao

[@RM-gm7lu]

Not a bad place to end up!

[@brokentombot]

You're the cool version of insane.

[@ThePigeon5734]

@Ramzan good, now I don't have search that myself

[@stevealaska73]

I feel smarter because of the 6 minutes you've shared with me. Thank you.