let's fix it 2021 ram 1500 amp install

Let's fix it 2021 ram 1500 amp install this is a troubleshooting video where we had to remove old aftermarket amplifiers and all wiring components and install his new amps and clean everything up it was a 6 part series that I made 1 video for the KZbin audience
*SUBSCRIBE FOR MORE CAR AUDIO DIY TUTORIALS *radio removals, radio installs, speaker replacement, speaker installs, car audio reviews and much more.
🔻
Parts used for this install are:
SMD ANL Fuse Holder www.jpsaudio.c...
SMD Dual ANL Fuse Holder www.jpsaudio.c...
SMD UB4 Distroblock www.jpsaudio.c...
TAGS: #caraudioinstallation #ram1500 #ampinstall
🔻
Did this video help you? Want to support the Channel? Show Your Support on:
JP'S AUDIO✅️
www.jpsaudio.c...
OR
Patreon
www.patreon.co...
🔻
WHAT TO WATCH NEXT:
HOW TO WIRE A RADIO: • Car stereo wiring harn...
CAR STEREO TROUBLESHOOTING
• Things to check if you...
HOW TO SAFELY TAP INTO YOUR CAR FUSEBOX: • HOW TO SAFELY TAP INTO...
HOW TO WIRE SUBWOOFERS: • how to wire subwoofers...
HOW TO INSTALL AN AMP TO YOUR FACTORY RADIO • how to install a loc -...
HOW TO INSTALL AN AMPLIFIER • How to install a sub a...
AMP TROUBLESHOOTING
• Amplifer Troubleshooti...
HOW TO PLAYIST: • how to
🔻
~Check out my first channel if you love BASS~ / jpsaudio08
🔻
~Tools I Use almost everyday~
NEW Milwaukee right angle driver amzn.to/2t4mDvM
NEW Milwaukee right angle drill amzn.to/2GwZAwQ
Install bay panel removal tools: www.jpsaudio.c...
Install bay Speaker tester www.jpsaudio.c...
Digital Multimeter: amzn.to/2Hcz111
Milwaukee drills: amzn.to/2Lxvu1y

[@MeetTheSLAYER]

Well done cleaning up another shops mess. If only all shops spent the time to do it right in the first place. I installed my equipment on my truck, and yes I do need to go back and clean it all up. I as well used a 0 gauge power wire going to a power distribution block with 2 4 gauge going out to the amplifiers, and used a ground block with 2 4 gauge going in and 1 0 gauge going out.

[@TrevorLahey1]

Beautiful install, man

[@christianbernal4648]

How did you secure the board to the back of the truck?

[@rubenreyes1436]

Clean job! Did you run the power wire through the same boot as the last shop? If so how did you seal it? If not where did you go through firewall?

[@MeetTheSLAYER]

In the video he did state that they went through the same boot as the previous shop, but went back to the boot to repair the slice and dice from the previous shop, they did not show what they did to repair it though.

[@chriskramer5737]

How did you fuse the power wires together

[@wj1023]

Previous shop is called " Dude Down The Street Audio" 😬

[@christianbernal4648]

Was this on a classic or the newer mode rams?

[@christianbernal4648]

I need to do this on a 1500 classic

[@josh_chetty]

Hi ...what happens if the sub is 10 000w peak and 650rms and the amplifier is 8000w and 700rms ....can u explain this plz

[@MeetTheSLAYER]

That is easy, set your gain properly so you do not smoke the sub. Having more RMS from the amp than what the sub can handle is not a problem. The higher you set the gain more power goes to the sub, so if you set the gain to high you will smoke the sub. While having more RMS power in the amp than what the sub can handle mean less stress on the amp thus giving it a longer life.

[@2222MUDDYWATERS]

Well done sir