That was very informative, I have worn control arm bushings and they knock like hell on any road imperfections but are very quiet on a smooth road.
@hepper74 жыл бұрын
It needed another alignment. They didn't do it right the first time. Much better now. Thank you
@herunpersun6462 жыл бұрын
You have given me a lot of clues where to look for the clanking noise on my A180CDI, I am very grateful for your simple advise,which I did not get from the Mercedes garages Thanks again
@E2018-q2b3 жыл бұрын
All my vehicles have had too much spirited driving, the plastic carpet always falls off. You have such impressive tools that would cost me 1000 GBP... but...I will still have a try and teach my girls. Garage men keep holding us to Randsome otherwise. Thanks for the enthusiastic sharing.
@onlyonecannoli39524 жыл бұрын
Your diagnosis mostly applies to severely worn out ball joints. They will start creating other symptoms before you hear such "clunking" noise...such as the steering wheel wandering slightly from side to side at speed when encountering imperfections on the road (this also applies to worn out bushings in the lower control arm, as well as upper control arm [if the vehicle is so equipped]), as well as vibration through the steering wheel.
@山内淳カイル-i5d2 жыл бұрын
Welp this comment just pinpointed what's exactly wrong with our car.
@ANOTHERMFER2 жыл бұрын
@@山内淳カイル-i5d gg
@patrickdabs2 жыл бұрын
This is great diagnostic info. You’ll notice after a few ball joint replacements that the clunks only come after the ball has worn beyond the point no return. You’ll notice steering play on imperfect roads before any kind of clunks, but once they’re clunking they’re completely toast, and you’ll have a lot of feedback over any kind of bumps.
@paralelmind2 жыл бұрын
Including car shaking when braking?
@SiriusXI2 жыл бұрын
@@patrickdabs so my car clunks over bumps, seems to float around the road as well as the steering wheel vibrates, I also notice that all mirrors have a vibration even when not going over bumps and the passenger seat shakes going over bumps, would this have to do with the control arms being worn or possible having some bushings worn out?
@mateostudent71663 жыл бұрын
2:36
@Pookiestud3 жыл бұрын
Hahaha!
@marcpadilla10942 жыл бұрын
These are helpful videos to narrow down potential problems. Rising prices and green new prejudices can ruin your holidays.
@jackmeredith4412 жыл бұрын
I have a 2010 CRV that started a metallic squeaking sound, which I believed to be the ball joints drying out. The rubber boot around the joint was pretty much collapsed, so I took a grease gun with a hypodermic needle and pumped grease into the boot / joint. The noise has decreased a lot, but this will only buy some time. It’s an old trick a mechanic friend showed me years ago. Wish they would go back to using grease fittings again but they make more $ fixing problems than preventing them.
@rogeliorodriguez85183 жыл бұрын
I can hear it perfectly. Great info but not the problem I have. Good video!
@nomadicroadrat3 жыл бұрын
Thanks for the informative video. I definitely heard the clunking noise you mention. The mechanic has basically told me what you stated, so am more confident that the problem is the ball joint.
@obazaar33633 жыл бұрын
The reason why all driver side ball joints are failing is teh city man hole covers. Thats why I always take the center lanes, it will save you a lot of money, it prevents tire pinch, bent rims, ball joint and longer lasting shocks. So keep center lanes and stay away from the left lanes and those nasty man hole covers that are never level to the road, some can have 1-2 inch drop.
@chavagarcia83905 жыл бұрын
I have definitely had to replace the sway bar links on my Subaru, same year same model. The clunk sound way worse than it is, but easy fix . Your videos are great! Thanks so much.
@CarsNToys5 жыл бұрын
Thank you! Appreciate the feedback!
@perezote68464 жыл бұрын
What Subaru do you have my man?
@perezote68464 жыл бұрын
I have loud clunks but not necessarily from bumps but it is loud, what did you fix? Thank you!
@davidedmundson84023 жыл бұрын
Worn sway bar links usually make a sound that is more like a tap or a click (and less like a clunk).
@mmpiforall59133 жыл бұрын
When it comes to isolating sway bar links, etc, try using a rubber mallet, tap the parts to see if they click or chunk, using varying amounts of force. Strike from different sides and compare. Compare left to right sides of the car. On sway bar links be sure car is level or they'll be under heavy load. Don't use a steel hammer.
@UkrainianBazooka Жыл бұрын
Huh, good tip. I'll have to do that when I get my car up this weekend. Thank you.
@mmpiforall5913 Жыл бұрын
@@UkrainianBazooka remember, rubber, not a steel/metal hammer, or the 'clang' of the strike is what you'll hear rather then the suspension. (also never whack the Cat, ceramic wafers inside will break) LOL!
@niewojt2 жыл бұрын
My 2011 Accord sounded like a steering problem. It was the ball joints. The sound was like two pieces of leather rubbing together. For two years no one could figure it out. The dealership said it was the front struts. Another mechanic said it was the steering fluid. Nearly 2 years later after those wrong diagnosis the sound got worse. That’s when the dealership figured it out. My car is in Toronto and the ball joints were changed at 294,000 km. Replacing both ball joints and wheels alignment: $915 after tax (Feb 2022) at the dealership.
@arvina57492 ай бұрын
This is great!! thank you for this video. I have those same noises when driving over speed hump or small potholes and I couldn't figure it out. Googled it but i got some uncertain answers but your video gave an example of the "thud" sound and now I know what I need to do. Thanks again! I am not a subscriber you have some great videos.
@peterfranks76193 жыл бұрын
Great vide, I thought my shocks were worn out but took it to the dealership and it was balljoints front axle.
@charlesholtzclaw78623 жыл бұрын
You described the way and it sounds 100% right.
@rusticyouthbh63194 жыл бұрын
Dude don’t stop talking to hear it
@KikoLugo214 жыл бұрын
Rightt omg he never shut up jaja
@jamesellis3644 жыл бұрын
For the people saying they can't hear it you need to get your ears checked
@njmenaceify4 жыл бұрын
he stops talking when he hits the bumps and you can clearly hear it
@minecrafterselite13 жыл бұрын
it wasnt that hard to hear even with him talking you tard
@lizsines78463 жыл бұрын
Exactly what I was thinking dude
@c22to5 жыл бұрын
Thank you. So true. My car has these same exact symptoms
@carln13033 жыл бұрын
fantastic explanation and diagnosis of a very common problem. well done.
@midnightraiin40353 жыл бұрын
love the minus sway isolation test!!
@RMalai2 жыл бұрын
CarsNToys, thank you for making this video. I have a 07 nissan sentra and I have been driving my car with this problem (feeling all the small road bumps/ridges, holes with that thumping noise). On top of it, it also vibrates a lot. not the steering wheel, but the body. hopefully after I replace the control arms, front struts, may be the outer tie rods, and do the alignment, finally this will also be fixed, so I can have a comfortable ride.
@grayzzor76pg2 жыл бұрын
Got Same issue with my Audi,I will check all what you said,great advice for a novice like me!
@leesway4 жыл бұрын
Wow cool that people can tell what's wrong based on sound and the situation
@stevew61413 жыл бұрын
Was waiting for him to pull out the roadkill from under the hood!! Would explain the louder the faster you go theory😂 Poor squirrel was like whoaaaaaaaaaaaaaa the faster he got!!
@martymckay2972 жыл бұрын
Too much talking not rough listening
@adewey33 Жыл бұрын
My 2014 Chevy Suburban only does a “clunk” sound when going from stop and go. When moving along or hitting speed bumps, there’s no clunking. Only when car is idling and you start to move , then it clunks one time at left front tire. I did that 12 to 6 tilt on the wheel, and it has significant movement
@samsonn25 Жыл бұрын
Yeah, is alot of stuff down there, struts, upper strut mounts, sway bar links, ball joints, and upper and lower bushings inner or outer tie rods
@robertwolfe4093 жыл бұрын
I hear a clickity clackety noise thats only heard on passenger side & from drivers side only hear it when passing walls/tunnels, up hills, in reverse(?), only in motion
@marcusdub07 Жыл бұрын
Did you ever find out what the clicking noise was? I've got the same sound, and metal clanking now.
@kart64silver7 Жыл бұрын
What about a creaking noise over bumps?
@milfordcivic6755 Жыл бұрын
We can't hear the clunking because you keep talking.
@viscioushattermaid44105 жыл бұрын
This guy has some great videos on oils and filters too!
@shawakimurray88252 жыл бұрын
Nice help I'll try it now tired of that noise
@phxrsx Жыл бұрын
How does the clunking differ from a bad ball joint vs bad lower control arm bushings?
@alundrasrt9 ай бұрын
or upper strut bearing
@davidsphone84494 жыл бұрын
Thank you for sharing your time and talent. Aloha
@bobbarker32484 жыл бұрын
A broken spring can cause a thump or clunk sound.
@smoknbobmarle31694 жыл бұрын
I been looking for something this informative thank you subbed too
@MUHAMMADKHAN-pe7ez5 жыл бұрын
you speak simple English. you accent is clear and you do not speak fast. ur excellent instructor. you can make the viewers "mechanic".
@Bo-tt8cy2 ай бұрын
Its confusing with the sound of a worn out strut bushing. I replaced my whole suspension last year and now this sound started last week, slightly on day one but only a week later its getting extreme. I believe its the ball joint because all parts were premium except the ball joint. Premium quality ball joints were sold out so bought a cheap one.
@patrickgumby23463 жыл бұрын
Really helpful and a simple process to follow. Thank you👍
@CarsNToys3 жыл бұрын
Glad it was helpful!
@porticoman3 жыл бұрын
That’s been helpful. Just fitted new front struts, strut mounts, drop links and sway bar bushings which has done a lot, but some clunking remains. It’s wheels off time! Again. Might just give the car a Viking funeral and get something new. But where is the fun in that?
@ricky-sanchez3 жыл бұрын
New cars are not as much fun as they seem.
@wilborth5th4 жыл бұрын
Thank you for this great video, I basically replace the whole steering system on my old dodge van, and still have the pop noise, sure enough the lower control arm still not replaced, that’s my next project along with coil springs, thanks again
@CarsNToys4 жыл бұрын
Happy to help. I did the lower control arms recently - kzbin.info/www/bejne/fIilq4Cqj96Zjs0
@KarlCudiCash36693 жыл бұрын
Nice dude. Found this video just in time. I was getting ready to tear my front end suspensions apart to find the thing thunking and clunking in the same exact way you described in the video. I'm gonna subscribe to your channel now if that's ok.
@oceanwaves832 жыл бұрын
Well that is officially the first time i ever heard "I'm gonna subscribe to your channel now if that's ok" Lmao you're nicer than Stephen Wonderboy Thompson!! 🤣
@amiquinn5963 Жыл бұрын
So many different noises. I got into an accident and a lot of the suspension parts were damaged. Lower control arm, drivers side, sway bars, put new shocks. It's worse than it was before.
@mattway34965 жыл бұрын
I actually wouldn’t recommend removing the end links. I have the benefit of a lift but generally you can grab the sway bar near the end link and push and wiggle on it and find the play in it pretty easily especially if it’s bad enough to make noise - more metallic clanky sounds over light bumps. But the nuts on your end links can be a real pain in the ass. They seize depending on the age. Sometimes badly. For the ball joints, a Large pry bar with the car off the ground can work similarly to your pulling on the bottom of the wheel . It might make it so one person can pry and watch the ball joint for play. I use the camera at home a lot when I don’t have a second person. Good trick for checking for spark when you’re alone.
@CarsNToys5 жыл бұрын
Thanks for the feedback! Yes, the factory end links often strip out. Very frustrating to say the least.
@Rob-kv3ry5 жыл бұрын
how would an impact fair on taking those end link nuts off, on your car?
@relaxgaming88722 күн бұрын
I only get clucking when I move from a stand still for a split sec. No sounds over bumps or when I turn. It only happens from stand still as I step on the gas.
@2bsurreal653 Жыл бұрын
Great video you helped confirm my suspicion 💯🖤
@JulyRobbins3 жыл бұрын
Thank you so much! My Jeep just started doing this only 45k miles too ugh but again ty you helped me
@joshawesome15573 жыл бұрын
Should have bought a 4 runner
@JulyRobbins3 жыл бұрын
@@joshawesome1557 eh don’t like them
@TehDavieRawrs3 жыл бұрын
Great vid forget the negative clear as a whistle makes sense
@oquenderebiqua3 жыл бұрын
Super helpful video dude.. thanks so much ! Regards
@josesoyelgatovoladorhernan30493 жыл бұрын
Good information brother thank you
@ravengarnet59673 жыл бұрын
If you stop talking for a second we could hear it when you're driving.
@tylertutt31413 жыл бұрын
You can hear it perfectly, Raven.
@thatdirtymichiganmusician10383 жыл бұрын
It’s not that difficult to hear
@hellonwheels43742 жыл бұрын
🤣🤣🤣🤣🤣🤣🤣🤣🤣🤣🤣🤣🤣
@Quest4Unknown Жыл бұрын
Tie rods, ball joints are usually the clunk noise going over bumps n potholes.
@amyshaw4442 жыл бұрын
Thank you so much this was very helpful
@paulgilraine31273 жыл бұрын
Think I have the same noise coming from the front passenger side just a bit less noisy on my car so it was hard to hear at times where it was coming from don't think I can do the job myself so it's off to the mechanic tomorrow , hopefully it's easy fixed I'm sure it's the same thing wrong on my car good video anyway .
@karinasleftknee19953 жыл бұрын
My car started making that sound in exactly that situation since yesterday omg
@WhoWhereTheBee2 жыл бұрын
I'm the case of my '93 Civic, it clunks when turning to the right, some times when going straight and not at all when turning to the left, because of that and a squeaking sound when the suspension goes up and down a bit (which you can fell even while pressing down the car) I can say that it is the upper ball joint, so I'll be changing the control arm. Let's hope that it's just that.
@joshmurphy97472 ай бұрын
What would cause my truck to make a squeaking sound when turning or going over a bump?
@doubleitp5 жыл бұрын
Symptoms of failed ball joints include: 1) Clunking Noises From the Front Suspension. One of the most common symptoms of a problem with suspension ball joints is clunking noises coming from the vehicle's front suspension. 2) Excessive Vibration From the Front of the Vehicle. 3) Uneven Wear on Front Tires. 4) Steering Wheel Wandering to the Left or Right.
@leonarddroneview69475 жыл бұрын
Curtis Braun I’m having an issue with my car where when I break on the highway I get a lot of vibration I have replace the rotors and pads still has not fixed the problem can a, bad ball joint cause vibration when breaking
@doubleitp5 жыл бұрын
@@leonarddroneview6947 -out of round tires, unbalanced tires, brake rotors, brake drums, worn suspension (struts worn, etc.) Even an out of true wheel hub would have lead to shaking also
@leonarddroneview69475 жыл бұрын
Curtis Braun thanks for the reply I’m going to rotate my tires see if it changes I also have some pretty cheap aftermarket struts on the front of the car they have about 40,000 miles on them now Maybe they could be the problem
@doubleitp5 жыл бұрын
@@leonarddroneview6947 you're welcome!
@paralelmind2 жыл бұрын
@@leonarddroneview6947 hi! Have you fixed the vibration problem when braking? If yes, what was? Thanks!
@TheCastedone4 жыл бұрын
My steering is very wobbly and I'm getting very bad wear on the outside of my tire. I dont have any clunks or anything but i believe the ball joints are far too loose on the front.
@outlaw49724 жыл бұрын
Tie rods
@rina2012ful5 жыл бұрын
Thank you. My car has that clinking metal sound from the front driver's side when i drive on bumpy or uneven road. The mechanic said that it is caused by worn out ball joint and exhaust bar. I don't really understand what has that front clinking sound got to do with the exhaust bar. The exhaust bar i just had it replaced 3 months ago. I really hope you could enlighten me on this.
@773Josh4 жыл бұрын
might be stabilizer links . this was my problem after bad ball joints repaired
@andrewowen5336 Жыл бұрын
Thank you! Very helpful
@stevepalenicek46902 жыл бұрын
Thanks .cars always breaking
@sempfi224 жыл бұрын
Mine makes squeaky noises at low speeds (less than 20mph), closing the driver door, shaking the vehicle, etc. Never when I go fast. I just got a 2nd opinion for $1400 for parts and labor (2 control arm with ball joint and sway bar link/kit)? I'm seeking a third opinion, tomorrow. I don't want to continue throwing money away and the problem exist. My first quote said bad cv axle. Second, mechanic said it wasn't that, because it's not clonking.
@zaneseligman13135 ай бұрын
Not sure what year you have - mines a 2012. I replaced the loaded struts, tip control arm and ball joint, bottom ball joint, tie rod and sway bar linkage. Then it developed a horrific ‘squeak ’ narrowed it down to bottom control arm bushing. It stopped before I bought the parts.- then (now) I have the ‘clunk’. I had to smile when you said you don’t want to dump a buncha money in it. It seams that’s all I’ve done. I have a 2 page list of parts I’ve replaced or had replaced. I’m normally pretty hard on my trucks - but not this one. This one has been like this while being pretty much babied. If you can get out of the trap- do it before you start sinking money it
@zaneseligman13135 ай бұрын
Where you get stuck is that it’s a super nice , comfortable, easy to drive, big (if you like big vehicles) good looking truck. I think Ford has a buncha good ideas- just not really the quality knowledge to make it all work
@jasonlewis61164 ай бұрын
Think that's the problem with my golf.. lower ball joint.. thx
@brentjodrey5114 Жыл бұрын
excellent explained video
@mbnbr08512 жыл бұрын
Well said brotha thanks for the info.
@alfredo209ful Жыл бұрын
Any time i turn I hear a squeal, any guesses? It’s only when i turn right too
@vincentvanderbilt55982 ай бұрын
Im so frustated because this is exactly what I hear whenever I drive on uneven road surfaces or mini bumps. I got a brand new 2023 Kia soul, just less than 15k miles on the odo, rattling noise can be heard near front end passenger side. Brought it to first Kia dealership and they couldnt replicate the sound and end up not fixing the problem at all.
@nikkogutierrez5393 Жыл бұрын
Thank you
@chadl52332 жыл бұрын
You can't hear nothing when you talking
@robertwolfe4093 жыл бұрын
Maybe its a wheel bearing & when replacing best to get both replaced right?
@colelaffredo36272 жыл бұрын
and my sway bar bushing was hanging off the spot it’s supposed to be at which might explain the clunking for mine
@johnson36herbalife3 ай бұрын
Nice video.can u try put cameraunder and more explain
@jameswaugh115 Жыл бұрын
Yes i hear it & my 2011 cadillac srx sounds just like that😮
@gabrielchico51294 жыл бұрын
Very helpful video,you are good teacher!!👍
@davidtrezelle2082 жыл бұрын
Thanks bro this may be my problem...one more question can a bad ball joint also cause short rattling sound when passing on rough roads ?
@timothykwasnik14212 жыл бұрын
If you turn the steering wheel and it creaks bad ball joints
@nordmode95915 жыл бұрын
Quality information!
@CarsNToys5 жыл бұрын
Thank you. Hope it helped!
@Horano_official2 жыл бұрын
If you use at least one hand brother you could save lives and control your vehicle if the occasion arises where something happens out of nowhere
@notbanksy82943 жыл бұрын
My front driver side wheel is squirrely af, thought lower ball joint? But think it's the wheel bearing. Good vid tho sir.
@robertserrato35966 ай бұрын
My car makes a clunking noise when I put it in reverse. Also a slight clunking noise when I start to slow down at a stop sign.
@SportsMusicCars4 ай бұрын
trans mount
@ezkempinkemp346710 ай бұрын
Thanks!
@marinddaaa3 жыл бұрын
Hey there, thank you for the very informative video, I have similar issue in my Vw shuttle t6, I am hearing thuming noise on uneven surface, I have changed the dropping links. But problem is still there. I feel while driving my van is going to roll down on turns and have less grip. Could you pls advise anything? Many thanks
@le0_b2 жыл бұрын
Christ, I replaced both lower control arms only a year ago and now the drivers side lower ball joint is an advisory on the MOT AGAIN! I can't seem to get rid of this knocking and clunking when driving which is very frustrating!
@_madpanda Жыл бұрын
Dude I'm trying to pick up the sound but you talk too much 😬
@alicehenderson79834 ай бұрын
@_skadoozh, me too, 😂,
@jadagreen232 жыл бұрын
Great video Thank You
@mrdave7775 жыл бұрын
THANK YOU SO MUCH.
@CarsNToys5 жыл бұрын
Glad to help!
@karinasleftknee19953 жыл бұрын
From when you first start hearing thing, how long till you HAVE to repair it??
@kewinjka2 жыл бұрын
Very helpful. Thanks !!
@CarsNToys2 жыл бұрын
Glad to hear that!
@PaulMcLove3 жыл бұрын
Thanks for posting ‼️ 👍😉😀
@rebel.mma.youtube3 жыл бұрын
Amazing. Very very good video
@richardanthony6303 жыл бұрын
My F150 truck shakes at 50 miles an hour and then goes away until 70 miles an hour what is doing that I’ve checked tires I’ve checked rims I’ve rotated tires I’ve done front alignment I put in shocks now they say they want to put in ball joints any suggestions?
@rbmtopgear76822 жыл бұрын
Can a bad ball joint make the steering wheel vibrate at speed
@sidthetech76233 жыл бұрын
My honda civic 2015 makes a subtle clanky-crunch noise from the front right wheel when I go over speed bumps... almost sounds like getting off an old matress?
@jackslater2300116 ай бұрын
My car pops when turning the steering wheel while sitting still or when moving at low speeds. It has 93,000 miles on it.
@dariogomez1673 Жыл бұрын
Will my car lose control.. untill I can get mine replaced.
@Markbabb3 жыл бұрын
Dose it happen while you brake car is making a thumping noise in the right front I hear a thumping