M50b25 3.0 Stroker + m3evo itb

Instagram: tomas.mochan
Engine specs:
M50b25
3.0 stroker
Cat cams
Itb e36 m3 3.2 evo
Light hydraulic lifters
S50/54 oil filter housing
Lightweight flywheel
Hds clutch plate
Etc.

[@miro20cm]

best bmw engine of all time this m50

[@mitovfilms2009]

damn dat throttle respons XD

[@Kastro876]

That shit revved so quick

[@MrDragoniso]

Pěkná práce na strokeru :)

[@4g63_Everything]

Nice build, want to hear this scream on the freeway 😎👌🏼

[@beqaoniani1579]

It's very cool, which computer is it on?

[@ST170Thomas]

Hey, how hard is it to fit the ITB from The s50 to the M52/m50 head?

[@BillyTheSKID]

Fitting them is the easy part, tuning is most difficult

[@B58_Alex]

Very nice 🥰✌🏼

[@e30centreofficial43]

What about injector angle what did you do to compensate this?

[@andreimelnicov2787]

Merge super👍

[@BMW-pg3bg]

👍👍👍👍👍👍👍👍

[@michalrychlovsky4062]

pecka

[@fahriakman7726]

M50b32 3.2 liter, m50b25 2.5 liter

[@juusesaarinen8976]

Stroker

[@user-cv4bw5fn8h]

хочу машину с таким мотором, который не стыдно показать будет

[@user-dr6uc9ud6d]

Хоти

[@stuntmaniac7233]

From what engine you have light hydraulic lifters ? M54 ? Can you tell me because i dont want stock M50 lifters

[@psychosocial2006]

m54 has the lightest ones

[@TomasMochan]

No, i used lifters from VOLVO

[@mrkamata5570]

What tps you use from s50 or m50?

[@cesareliel4797]

nice

[@edisisler6746]

trying to do everything best and still moving the car with the maf sensor

[@user-gk7zh3he6v]

Cool

[@damianbmw2226]

I buy this engine :D

[@TomasMochan]

Damian Żmuda no problem, I want 90.000,- CZk

[@autotuner948]

You still sell the engine

[@zokizoki2524]

is that a steel or plastic valve cover?

[@TomasMochan]

Aluminium. Original m50.

[@placeholdername3206]

@@TomasMochan Its magnesium on M50 and M60. Very nice build you have. Was stroker worth it? I also have M50 non vanos and M54B30 engine with blown headgasket sitting. I want to make stroker but not sure if not so good for revs with long stroke

[@pawetrocki5781]

Do you use m3 oil separator and hoses from S50 ? Thanks

[@TomasMochan]

No, custom build.

[@nordalexs9537]

Бляяяя работает как жигули

[@WW-by2cs]

До него ,дерьму жугулии далеко

[@user-kf4lx4fs8e]

👍

[@ubpak7346]

Bro its bosch or siemens?if ita bosch 402 or 405?if its siemens ms41.0 or ms41.1?

[@TomasMochan]

prrr i think bosch 402 :)

[@albanneroff5920]

Its a bosch 403 ecu non vanos

[@lukasnevidzan5523]

Zdarec,prvom rade chcem pochvalit project super dotiahnute to mate :)... Po stroker prestavbach googlim skoro už rok. chcem spravit taky budget project s M50B20 NV dat to na B25 ,pomocou kluky 82,8m (2,5TDS) ,130mm ojnic 2,5tds, a piestov 39,425mm ( 2,5TDS)...pokial som sa dočital spravne zo zahraničnych for "deck height" vyska bloku by mala byt 210mm u B20 ? mne to vyjde 210,825mm cela zostava.. tesnenie použijem seria (čo najvyšie) s piestou budem davat odsustružovat podla vypočitaneho CR. Každopadne uvidime ,ked budete niečo vediet viac resp. poradit usmernit budem rad :) A ked už vas tu mam sa chcem spytat. mnoho ludi použiva jednohmotny zotrvak a lamelu davaju 240mm( B28/M3 atd. lenže čo som na ETK pozeral tak len 2mass zotrvačniky maju 240mm opornu plochu pre lamelu ako sa to rieši? tiež odsustruženim ? :) potom to zakončia pritlačakoms 3,0D M57D30 ten mam tiež kupeny rozstup dier na B20 zotrvak sedi akurat ten pritlačak je nizky lamela volna :D Ale to len tak na okraj .

[@TomasMochan]

Ahoj, děkuji a držím palce s tvým projektem :)

[@garagepollet835]

What cat cams did you use?

[@MrDragoniso]

I think from m54 3.0

[@TomasMochan]

I used custom Cat cams 2x intake m50b25. One on inlet site and the second on exhaust.

[@abhibhattacharyya3168]

@@TomasMochan What are the measurements/duration of cams used?

[@TomasMochan]

@@abhibhattacharyya3168 Hi, i can´t remember that.. :/

[@DatanoobPlays]

stock m50b25 maf?

[@onomikeono4181]

I use 540 maf sensor in 325 housing

[@kevinknosala6679]

I have a m50b25 as well and i’ve been wanting to stroke it and run itb and i was just wondering if you ever ran it on a dyno and tested to see the horsepower you get out of the engine

[@robertsdmitrocenko]

I know for a fact 3.0 strokers they can get to 240hp. With ITB's that could be a 260-280hp car.

[@braydensummerlin]

What itbs?

[@TomasMochan]

ITB is from S50b32 euro spec engine by e36 M3 evo:))

[@user-kf2dc9zz2y]

How much hp nm . Rpm ? Engine

[@TomasMochan]

It should have 8000rpm :) but ECU is not remap :)

[@TomasMochan]

Hello everybody, if you want know spec of this engine. Go to visit on Facebook site - TM BMW Engine or TM BMW Vanos System. By and have a nice day.

[@user-ui6bo7lk7g]

Что?)

[@danielfranke5570]

What ECU setup?

[@TomasMochan]

Hi, this is the one of the first starts.... Engine running on stock ECU Bosch DME - I must repamed it :)

[@danielfranke5570]

@@TomasMochan thanks for the reply, how did it drive before remap? I want to know if I will be able to drive 100km to tuner.. thanks.

[@TomasMochan]

@@danielfranke5570 very very very bad... the car is not ready to drive :D ....

[@onomikeono4181]

@@danielfranke5570 i use stock m3 chip on my m50b30tu stroker no check engine with 540 maf sensor

[@user-fy6cc3sq3f]

3 литра длинноходный, крутить плохо...

[@pirat.paulie]

*Tvrdej Bob?* WTF

[@TomasMochan]

Ale nééé.... brácha má přezdívku bob.... -_-.... s tím magorem nás prosím nesrovnávej:D ...

[@pirat.paulie]

Já měl za to, že tam vidím i jeho ksicht :D