MagnaClean Professional 2 Installation, Pipe Work Adjustment, See it in Operation, Review 2021

[@handyjayes1]

Can't help but think you are the perfect candidate for a major manufacturer to take on as their 'trainer'. You sure cover absolutely everything that most plumbers/ engineers would assume was 'obvious'. Good stuff 👌

[@GsySaxMan]

I am not a plumber but wanted to say that your attention to detail is extremely professional and to be applauded, I suspect that you get a lot of personal satisfaction by doing the work to your high standards; if only......

[@HektorBandimar]

I wish you were my local heating engineer, your professional approach and expertise to your trade is admirable.

[@matthewfalls2141]

Thanks for showing the details, really helpful for a routine clean out

[@garranstvall1442]

Brilliant video Mark, just what I’ve been looking for. Keep the great content coming. 👍🏾

[@davidcoleman6032]

Superb video Mark! Many thanks for posting. 👍

[@elgera2k]

Thank you for the useful video Mark. I have an old Eco Max boiler, there are about 6 pipes coming down from the boiler. In which of the pipes must this filter be fitted please?

[@MarkBallardLTDHeatingEngineer]

All the vaillant combination boilers the return pipe is the right hand pipe. For any boiler the easiest way to tell which is the return pipe, just run your central heating see which pipe gets hot first and then which pipe starts getting hot. that would be the return pipe. As the hot water returns from the heating to the boiler. hope that helps everyone

[@RichKeefe-w6c]

My boiler is less than the size of the magna clean from the roof and in the airing cupboard the pump is 6 inches off the floor before going left into the cylinder and right into the heating. The heating only pipe may be long enough is that a problem?

[@AndrewBulmer]

Great job well done

[@robertgoy9367]

can you help i have heating system that has solid fuel fire and a gas boiler to run it i am looking to fit a magnaclean professional 2 to my system but not sure where to fit it as the pipes for the heating go throw a dunsly tank to heat the water for the heating can i still put it near the gas boiler or should it go near the feed pipes at the dunsly tank .or the pipes near the solid fuel fire ?

[@Mintyz1zr]

Where can I get the o ring for my filter adey

[@spacecraftbuildingservices]

Very useful thanks.

[@IkeBrider]

I have a boiler with 15mm system, is it OK to fit this with reducers?

[@floatybyboaty]

Hi Mark, Adey have said i can fit on either the flow or return as i have a closed system. Is that correct please?

[@vickychest9533]

Can you fit one for me in SW15

[@jguk2597]

Do you have a video on flushing out your heating system? Great videos by the way so helpful

[@stratf0182]

Id also like a response to how you flush out a vented system please. 😃

[@ichdenker]

Great information

[@TheSweeney-UK]

How much would this usually cost off a tradesman? Great informative video .

[@MSKChess]

2 awesome

[@davebayliss3142]

The isolation valves on these are a nightmare. The lid is a nightmare I would swerve these

[@davebayliss3142]

This is what happens when you get your mate to install the boiler ,trying to get it done on the cheap

[@Ah85661]

Does this pipe get hot??

[@MB-zl3cn]

P.T.F.E. tape on a compression fitting !!? 🙈 Cowboy

[@tonestones9445]

Im not a plumber but also think whenever l do DIY plumbing lve never used plumbers mate or ptfe tape on a new fitting. Surely the olive should do the job as that is what its designed for? Perhaps if you have a leak from an old rad where the fitting has been strained after draining you may use it?