Can't help but think you are the perfect candidate for a major manufacturer to take on as their 'trainer'. You sure cover absolutely everything that most plumbers/ engineers would assume was 'obvious'. Good stuff 👌
@GsySaxMan2 жыл бұрын
I am not a plumber but wanted to say that your attention to detail is extremely professional and to be applauded, I suspect that you get a lot of personal satisfaction by doing the work to your high standards; if only......
@HektorBandimar Жыл бұрын
I wish you were my local heating engineer, your professional approach and expertise to your trade is admirable.
@davidcoleman60322 ай бұрын
Superb video Mark! Many thanks for posting. 👍
@garranstvall14423 жыл бұрын
Brilliant video Mark, just what I’ve been looking for. Keep the great content coming. 👍🏾
@matthewfalls2141 Жыл бұрын
Thanks for showing the details, really helpful for a routine clean out
@AndrewBulmer Жыл бұрын
Great job well done
@elgera2k3 жыл бұрын
Thank you for the useful video Mark. I have an old Eco Max boiler, there are about 6 pipes coming down from the boiler. In which of the pipes must this filter be fitted please?
@MarkBallardLTD3 жыл бұрын
All the vaillant combination boilers the return pipe is the right hand pipe. For any boiler the easiest way to tell which is the return pipe, just run your central heating see which pipe gets hot first and then which pipe starts getting hot. that would be the return pipe. As the hot water returns from the heating to the boiler. hope that helps everyone
@spacecraftbuildingservices2 жыл бұрын
Very useful thanks.
@TheSweeney-UK Жыл бұрын
How much would this usually cost off a tradesman? Great informative video .
@RichKeefe-w6c7 ай бұрын
My boiler is less than the size of the magna clean from the roof and in the airing cupboard the pump is 6 inches off the floor before going left into the cylinder and right into the heating. The heating only pipe may be long enough is that a problem?
@Mintyz1zr6 ай бұрын
Where can I get the o ring for my filter adey
@robertgoy936710 ай бұрын
can you help i have heating system that has solid fuel fire and a gas boiler to run it i am looking to fit a magnaclean professional 2 to my system but not sure where to fit it as the pipes for the heating go throw a dunsly tank to heat the water for the heating can i still put it near the gas boiler or should it go near the feed pipes at the dunsly tank .or the pipes near the solid fuel fire ?
@floatybyboaty Жыл бұрын
Hi Mark, Adey have said i can fit on either the flow or return as i have a closed system. Is that correct please?
@ichdenker3 жыл бұрын
Great information
@IkeBrider Жыл бұрын
I have a boiler with 15mm system, is it OK to fit this with reducers?
@jguk25973 жыл бұрын
Do you have a video on flushing out your heating system? Great videos by the way so helpful
@stratf01822 жыл бұрын
Id also like a response to how you flush out a vented system please. 😃
@MSKChess3 жыл бұрын
2 awesome
@vickychest9533 Жыл бұрын
Can you fit one for me in SW15
@davebayliss3142 Жыл бұрын
This is what happens when you get your mate to install the boiler ,trying to get it done on the cheap
@davebayliss3142 Жыл бұрын
The isolation valves on these are a nightmare. The lid is a nightmare I would swerve these
@Ah856612 жыл бұрын
Does this pipe get hot??
@MB-zl3cn Жыл бұрын
P.T.F.E. tape on a compression fitting !!? 🙈 Cowboy
@tonestones944510 ай бұрын
Im not a plumber but also think whenever l do DIY plumbing lve never used plumbers mate or ptfe tape on a new fitting. Surely the olive should do the job as that is what its designed for? Perhaps if you have a leak from an old rad where the fitting has been strained after draining you may use it?