Mercedes W211 Rear SAM Autopsy

[@FloroBeggins]

Everyone has the same unanswered question! How did you get that last cover off??!!!

[@whlawson5812]

I think this type of problem is due to the cycle of high humidity + heat and the drop in ambient temperature. Then a little tiny bit of condensation here & there and repeating this over the years, plus a bit of dust, it resulted in this type of corrosion. What if as a PM, on your other circuit boards, you clean it up it with alcohol. Soft dried at 110 F max using a hair dryer. Then spray a layer of urethane made by CRC for coating circuit boards. Air dry it for 1 hour before soft dry it again with hair dryer?. Is it likely that PCBs in old Mercedes, or even the newer one, are not provided with a layer of protective coating?. Regards

[@alinuhadgalaxy]

I replaced my car sam fo MB cls 2010 cgi 350 grand edition 2010 But the motion sensor in the roof i discovered its not working like not go down mechanism I am not sure if its before replace the sam or after what could cause it? Btw all functions work right. Thanks for your answer

[@stevewanaka]

Thanks for this fantastic video. I have the exact same rear SAM on 2003 W211 (E320) and cannot figure out how you removed the cover that protects the circuit board components (the one that’s on your table in the background). The cover that holds the fuses and relays came off easily but now I’m stuck. Can you help me?

[@marouanemaths1880]

But in 4:20 how do you do for take off this plastic side

[@abyssalsoul6216]

09 e350. Do you think replacing this SAM would fix my left rear brake that is not illuminating when I apply brakes. Iv'e installed a new bulb assembly and still the same issue so i figure it is not the bulb.

[@stevewanaka]

I ended up replacing the SAM and everything works. Thanks!

[@inkdown]

How did you manage to take the front cover off this rear sam? The side where the capacitors and mosfets are soldered? I have all the other plastic casing off my module but can't seem to get that front side off.. I already removed the 7 screws that hold the board in place but it still seems stuck on there and I don't want to break or damage anything..

[@cali_cal]

how did it go?

[@donegal2010able]

Man I was jealous earlier when I saw the rear window curtain pop up never seen one of those. You got a god dam swimming pool. I got a two foot by two foot shower. Good video once I finally calmed down to watch it.

[@kennethfromkin6141]

Thanks!

[@christopheparre7904]

Thanks. How do you separate the board to the last cover after the black torx removal ?

[@Eetu_Veikkola]

With violence.

[@jeffryblankenship746]

How did we figure it out? Was it the corrosion in two small spots? Was this a lesson on salvaging fuses and relays?

[@vocals7693]

There's another video where someone cleaned corrosion off the front PCB SAM module (under the hood) using stiff brushes and Isopropyl Alcohol and it fixed the problem. As long as corrosion doesn't short out components or damage any electrical traces it could be salvaged.

[@Emiilhb]

Is it the samd module in R-class 2008model?? Whats the part number? :)

[@amerhussain1023]

Very useful

[@TheDomin8rr]

Nice follow-up. Was it discovered how moisture got in there? I've heard water can flow down radio antenna wire route from rear window but curious to know if taillight seals are also a potential source like in Tuscaloosa built ML & GL SUVs.

[@kennethfromkin6141]

I've heard that the MLs are notorious for having water get in through the rear lights -- but mine is an E Class -- different beast. I think that some water was coming through where the GPS antenna came through the body -- I put some silicone in there to try to seal -- but never confirmed dampness and I've never seen water in trunk

[@abyssalsoul6216]

On my 09 e350 water seeps in through the left drain channel that goes around the trunk lid . It is the channel that routes water from the bottom of the windshield and circles to the left and right of the rear quarter panels and end by the tail lights. On my 09 what holds the plastic trim piece are some pins that are pushed in to secure the panel and those pins have rubber washers that degrade with time and cause water to seep in. And guess what? one pin in particular is located just above the rear SAM. The fix is once you have installed new pins , is to smear some sealant over the pins to make them more water proof. I think water getting in through tail light assemblies would only create a humid condition in the area but getting in above from the leaky pin assembly , the drip is directly unto the SAM

[@martinsuperstar6049]

Put it in the oven at 120-140 Celsius for about 15min helps sometimes.

[@fuzzs8970]

Hi Nice steps for dismantling. Cleaning and reflow of the joints could have solved the issues

[@yosefelhurti301]

You don’t want to admit that ther are the best ever 😂😂😂😂

[@joecraigslist9467]

Great diagnosis. Some KZbin mechanics would have broken out an oscilloscope. One thing, did you check the relays?

[@kennethfromkin6141]

Didn't check them. Probably should do. Don't have an oscilloscope -- I don't have those skills

[@hermansukarno]

headlamp sebelah kiri saya mati. apakah kemungkinan kerusakannya? Thanks

[@geemanbmw]

Awesome content 👏 👌

[@nopointinasking]

Good work lads 👍🏻

[@تلااةا-ص5ق]

Thank you very much my dear brother

[@geojbig]

Good follow up, Thanks!

[@traqnsavov822]

if the patient is needs an autopsy, so he went a very badly!! hahahaha 😀😄😅

[@ابراهيمخيرالله-ق9ز]

اسباب تمنع راديو من العمل w211

[@jeffryblankenship746]

On and on droning. Guys Okay guys. Okay guys.....today guys. Comment guys.

[@joecraigslist9467]

Dr Dr give me the news.