Mikrotik point to point with good bandwidth

[@federoffm]

Thank you SO MUCH for this video! I was wandering around in the weeds with my new MikroTik radios (and I've done wireless bridging for decades). Very much appreciated. Thanks for taking the time.

[@timigate]

You are welcome,Matt

[@usmanisiaka7905]

Thanks so much for this beautiful lecture on

[@adityamohan85]

Is it possible to configure a fail over of yes how and each equipments to use. Are there risk of broadcast storms if configured incorrectly.

[@geoffreyjowa]

thank you sir. just one question. can i connect more than 1 client on the link or is it limited to only one client

[@timigate]

geoffrey fredericks you can only connect a client because it’s a point to point link. To connect multiple client, the wireless mode has to be set to AP bridge instead of bridge.

[@geoffreyjowa]

@@timigate can you explain how to do it

[@timigate]

@@geoffreyjowa www.timigate.com/2018/03/mikrotik-wireless-simple-access-point.html

[@shikharjoshi6111]

Respected sir, Whats the Max throughput of Netmetal 5 2x2mimo AP 922Hpacd-NM and Which Protocol is the best for PtP link of 50 Km? NV2 or any Other? How is the effect of Protocol ?

[@timigate]

There is no max throughput. Though Mikrotik claims you can get up to 800Mbps using Netmetals but this is dependent on LOS, frequency utilization and an TX power. NV2 will increase the bandwidth though the column for throughput wont show any values once you switch to NV2

[@shikharjoshi6111]

And also Whats the role of Country setting, & Distance setting on Wireless menu. Does it effect on Tx power? Which country has Maximum tx pwoer for Mikrotik Netmetal5?

[@timigate]

Each country has max TX power and a number of allowed frequencies from the 5GHz spectrum. You are to stick to the allowed frequencies in your country. Do a snoop test before choosing a frequency to avoid interference. I made a post on frequency selection here: www.timigate.com/2017/11/how-to-use-snooper-in-mikrotik-to.html

[@usmanisiaka7905]

Thanks so much for this beautiful lecture

[@timigate]

You are welcome

[@nurullahcaliskan]

is it ip adress static or dhcp ? how to take ip adress? by the way thanks for video :) :like:

[@timigate]

Nurullah ÇALIŞKAN IP is static. If u have a dhcp server configured on your network, then you can configure the bridge ports as dhcp clients.

[@shikharjoshi6111]

Dear Respected sir, I have a question for you. I have made a ptp link near about 71 Km long distance using both side NETMETAL 5 and Rocket Dish 34 Dbi. The signal strength is -62 to -64 dBm but CCQ is only 15% to 45% and randomly changes and throughput also. I have choose NV2 protocol and ACCESS POINT Bridge and STATION Bridge. How can i increase CCQ 99%? both device is ping @ 1ms latency. but when i connect another device from DEVICE A via winbox registration of ap failaure or link goes off. how to solve this issue?

[@timigate]

Configure the AP as bridge and the station as station wds. Also change the channel width to 40MHz turbo. Also do a snoop test to be sure you are using a frequency with less interference.

[@shikharjoshi6111]

Whats the max long range support by NETMETAL 5 device?

[@timigate]

Netmetal 5 using 34dbi dish works well on distance up to 50km. Yours is over 70Km hence the low throughput. U can increase the through by setting it in bridge-station wds and also changing the channel width to 40MHz turbo then work on the frequency to be sure it has less noise. I hope this helps.

[@shikharjoshi6111]

Dear sir, I have a Question that i never get proper answer till now. In current scenario I have been configured PPPoE server on Ether-3 on Mikrotik Router RB750Gr3. and Ether-1 is input and connected to VLAN Based network with Public ip Address. I have been configured PPP profile of 512k, 1Mbps, 2Mbps etc. for bandwidth shaping purpose. I want to pass KZbin Bandwidth 25Mbps download speed to all PPPoE users even they have been assigned 512k profile. I want to provide much more speed on KZbin, Facebook and Google traffic, HOW TO? Please answer my Question. I'm stuck here.

[@timigate]

(1) Create a layer 7 youtube rule(2)Using the mangle rule, create a packet mark that makes use of the layer 7 rule u created in step 1. (3) In simple queue, click on advance and select the packet mark created in step 2 and set the upload and download to 25Mbps. Good luck

[@jeremiahgborie3614]

Explicit Video. Thanks M?ichael for this wonderful and simplified Video. You sound like a SierraLeonean, you be salone borbor. ??????????????... hahahhahahah. I know it is not part of the tutorial , however I am just curious. Once more thanks for your professional video.

[@timigate]

Jeremiah Gborie Lol. I be Naija Borbor. Thanks for your kind words.