Monster Moto Throttle Adjustment GO FAST or SLOW

Adjust the speed of the Monster Moto for suitable use... #monstermoto #megamoto
Adjust at your own Risk! Other Videos related below...
Monster Moto Videos
Chain Adjustment - • Monster or Mega Moto C...
Oil Change - • Mega Moto & Monster Mo...
Throttle Adjustment - • Monster Moto Throttle ...
Clutch Maintenance - • Monster Moto Clutch Ma...
Oil Change How to - • Monster Moto Oil Chang...
Assembly & First Drive - • Monster Moto Mini Bike...
Tire Change Time - • Replacing Monster Moto...
Fun Videos
Monster Moto meets Snowmobile - • Monster Moto Meets Sno...
Monster Moto Full Throttle - • Monster Moto 80cc Full...
Birth Of My Monster Moto - • XT250 Birth of a Monst...
Monster Moto Road Warrier - • Monster Moto Road Warr...

[@Snailmailtrucker]

Just put a drop of ThreadLocker on the Adjusting bolt with the spring removed so it doesn't unscrew and fall off ! Liked/Subscribed !

[@kd_enterprise3404]

Good plan.. thanks for the comment !

[@gregsteele9002]

Yes this! AND I looped a skinny piece of solid wire through the coils of the small spring that hooks the bottom hole of the tall, long metal governor arm to the throttle linkage, (do not squish the spring coils completely, leave a little bit of slack), and now my MBX10 does 33 on the GPS

[@kd_enterprise3404]

Nice, my max is about 29 on average… lol… 😂

[@gregsteele9002]

@@kd_enterprise3404 mine was maxing out at 31, then I made a hook out of a metal coat hanger or something simular and dug that black, steel wool-looking spark arrestor out of the muffler . Then drilled a few extra 1/4 inch holes in the square air filter cover (took it off first) right where the carb opening goes, put the air filter back in and now does 33mph on pavement

[@ssbceez224]

Great video dude

[@kd_enterprise3404]

TheUnboxer thanks!

[@2xx768]

Mine has a little metal piece thing that stops it from going. Faster I took out the screw and it’s the same HELP PLS I wanna take it out

[@chriskobe8559]

What happens when you clean the air filter, would there be any difference

[@kd_enterprise3404]

Well, if everything else is operating normal, a dirty air filter will make the bike run rich, probably reduce speed and fuel economy...the key being, if everything else is functioning normal, such as carburetor and proper fuel, choke... Many things can impact operation...thanks for watching..

[@Mr1000fucks]

What is your weight? Planning to buy same mini bike and go off roading this summer.

[@kd_enterprise3404]

Well if you are 150 and under should be fine, if you are over that on hilly rough road better get a bike with a bigger engine and shocks.

[@Mr1000fucks]

Im 175 not about to go to up hills. Just flat gravel roads.thanks for the reply.

[@andreas6081]

Bro.. Im 190CM and weigh 98 kilos and this just doesnt stop, i can go anywere its so fun!!!

[@andreas6081]

Yo bro! Great video, whole FUCK it goes insanely much faster its insane. I dont even dare to push it to the limit its a rocket. Got it up to 60 kmh in like 4 seconds and then stopped hahaha. But what I wonder is, is this pushing the engine more than zip tie governor? And what happens if the screw falls of and gets lost?

[@kd_enterprise3404]

I think my screw fell out a long time ago.. it’s ok, you need to put thread locker on it. I have tried pushing the governor in, it goes faster! But I’m not sure how long the engine would last….

[@andreas6081]

@@kd_enterprise3404 but if i dont max it out, and just keep the power there if i would need it sometime, it wont affect the engine, correct? Thanks alot for answer. Also wonder, what do you think affect the engine the most, zip tie or this?

[@kd_enterprise3404]

@@andreas6081 I don’t think I’d zip tie it, the governor needs to move freely for normal riding. You might want to hook a string up to it and route it so u pull without moving hands off bars. Normally I just reach under and push it, but not the safest way to ride, so I can’t recommend it. … But again, running that thing all out, won’t last near as long…

[@andreas6081]

@@kd_enterprise3404 so you'd say it's safer for engine just loosing the screw than to use ziptie? And thank you so much for answer!!

[@kd_enterprise3404]

@@andreas6081 I’ve only adjusted the throttle, do some experiments… I can’t really say what is best or recommend mods… it’s at the users risk.. these days if someone gets hurt they sue. 😂..

[@beardedjalapeno5263]

I got mine used and that screw is long gone...

[@andreas6081]

What happened when you lost the screw?

[@beardedjalapeno5263]

@@andreas6081 nothing, just keeps going...