Replacing a Ford BA/BF Falcon Fuel Pump! The Quest for Maximum Flow

[@MotoringBoxTV]

Thanks for watching! Like, comment or sub to support the channel. 👕Or grab a shirt from www.motoringbox.com/shop

[@firstworldproblems6064]

hey man i put in a walbro pump with the upgraded assembly on the fg but also put in a evc throttle controller same time. does the assembly have to be pushed down in all the way cos mine was very springy and also does the black ring have to be turned down all the way? im havign some irregularities when coming to a stop its dipping sometimes but i think its the touching/changing the throttle controller while driving or its the pump. the car has been starting much smoother since the new pump. i also notice now i have had a 6 speed zf conversion the car runs bit warmer closer to middle temp alot. p.s. shes quite fast for a non turbo i tell you. running on 98 all the time n that

[@MotoringBoxTV]

I forgot to mention it in the video, but I also replaced the fuel filter too. After looking at the footage I still don't think this car is performing as good as it should be. As mentioned I hope to eventually move away from the piggy-back ECU and get a proper PCMTEC tune done on the car. Also this video wasn't intended as a DIY guide as I'm not an expert. Make up your own mind before deciding to attempt it yourself.

[@TheRealMrCods]

Maybe Haltech could hook you up?

[@MotoringBoxTV]

@@TheRealMrCods Wouldn't that be nice.

[@TheRealMrCods]

@@MotoringBoxTV Well I tweeted them on your behalf 👍

[@ut2k4wikichici]

Could be boost leak which I had on my ls at high rpm

[@MotoringBoxTV]

@@ut2k4wikichici definitely something I will be having a look at.

[@queenslandballistics2987]

Man your video uploads used to be lightyears apart now its just day after day. Good to see that your BA is finally getting some professional help here.

[@MotoringBoxTV]

I am trialing two per week, so long as the jobs are quick enough to finish both in the same day 👌

[@queenslandballistics2987]

@@MotoringBoxTV Yeah that's good Great Job! I think maybe look to finish the NC and the AU like the Turbo kit and mods then perhaps get a new car as a project if you want. But like I said great job and I am really pleased that the upload time between videos has been reduced alot so thanks.

[@firstworldproblems6064]

​@MotoringBoxTV hey man i put in a walbro pump with the upgraded assembly on the fg but also put in a evc throttle controller same time. does the assembly have to be pushed down in all the way cos mine was very springy and also does the black ring have to be turned down all the way? im havign some irregularities when coming to a stop its dipping sometimes but i think its the touching/changing the throttle controller while driving or its the pump. the car has been starting much smoother since the new pump. i also notice now i have had a 6 speed zf conversion the car runs bit warmer closer to middle temp alot. p.s. shes quite fast for a non turbo i tell you. running on 98 all the time n that

[@mahcooharper9577]

Pumping them out mate, well done See what I did there?

[@MotoringBoxTV]

👀👀

[@samcox9133]

He's got a good flow going at the moment!

[@johnwalters6025]

Delfi also do genuine parts. I reckon with how low the kms are it's probably original

[@brendankelly4329]

Delphi*

[@Fcool370]

I took mine out and replaced it yesterday and the pump that was in it was a Delphi

[@MotoringBoxTV]

Yeah, the more I read into it the more it looks like it was the stock pump. There weren't any markings or anything on the pump itself.

[@Fcool370]

@@MotoringBoxTV I think you are monitoring my falcon career with your plastic welding video notification hit my phone just as I was looking at my destroyed rear door handle

[@MotoringBoxTV]

Haha, please tell me what happens next then!

[@Fcool370]

@@MotoringBoxTV definitely wastegate actuator and boost solenoid clean

[@SneezerNZ]

I am replacing the fuel pump on my BA next week. Just don't know the condition after 18 years. Thanks for the tutorial. Always appreciated!

[@xprise814]

I miss my BA Turbo engine so much!!

[@alexandreb.1101]

MotoringBox is on a roll now! Great way to finish the day

[@SHOCKcustoms]

You upgraded the swirl pot and pump not just the pump... pump is the motor looking bit within the sniper pod. Should have gone the walbro 460 or 525 e85 compatible pump inc the big sniper pod. Get rid of the ancient history piggy back ecu and get a full pcm tec tune. Your issue will be the tune, not springs pump or filter. Have several of these cars.. pcm tec tune is the best for them. So much smoother and easy power. Love the content bro cheers. Nice to see you supporting tuners edge in coburg with your purchase. 😊

[@MotoringBoxTV]

Thanks for the comment mate! Definitely will go PCMTec or even Haltech if I am lucky.

[@1969Risky]

Delphi supplied products to Ford & Holden. Not sure on Toyota as I've not owned one for many years. Sean, have you checked your sparkplugs & leads? I was having the same problem with my ute recently so I replaced them & she's bang on. It also helps if you know a mechanic with a proper scan tool to re-check everything besides fault codes. Did the fuel filter show any particles? Living in a country area, we don't always get good clean fuel at the bowser. A mate's ute had crap in the tank so we cleaned the tank, replaced the filter, cleaned the lines, checked & cleaned the injectors & fuel rail. It's all a process of elimination until you find the cause.

[@MotoringBoxTV]

Spark plugs and coil packs were done in a previous video - they helped moreso with the rough idle I used to have, and then replacing the intake manifold gaskets fixed that for good. The old fuel filter looked very clean!

[@bossdog1480]

No leads on BA's...

[@1969Risky]

@@bossdog1480 Sorry mate, I'm used to working on L36, L67 & LS engines.

[@smithy2]

I like the quantity of content your dropping, other channels i really use to enjoy seem to have run out of idea in 2021

[@ut2k4wikichici]

Yeah its idling high check for vacuum and boost leak if you have a gauge it can help

[@thewholls7176]

Good job mate I just bought a Sniper 320LPM “big pod” for my BA V8 Fairlane so this video is helpful….!! The big pod has a 1L swirl pod to reduce starvation on cornering…..

[@willb6070]

Delphi is what actually used to be Delco herein the US. They used to be totally owned by GM (GM parts OEM for decades) until GM declared bankruptcy then spun them off separately with a new name. But they also make tons of electronic control modules for many auto manufacturers these days.

[@stevanzaharic]

Great job is done.It is very important for people who never done this job ,before procedure start,"no smoking cigarets"start car and pull out fuel fuse to relise preasure in tank and car will die withouth petrol which is very important first step.I have notes you did not have rubber seal on new pump which is going around bottom lips of pump and looks like that old seal is in bottom installed properly for preventing of petrol leakage.

[@imGlobL]

Good idea to mention to the viewers to disconnect the terminals from the battery for safety

[@stevanzaharic]

It is more important in this procedure to realise pressure from system "start car and pull out fuel fuse till engine stop".You were lucky your petrol tenk was under half and you did not have hight pressure in system, but disconect batery put wire from disconnected minus to plus will reset ECU to factory default and you will get more milage on clock and accelerator pedal and trotle need relearning proces or "calibration".It is professional explanation from Haynes repair manual book.After that your trotle will have hight respond and you will ask yourself how car performance is double hight than before procedure.

[@Gowieee]

Not necessary.

[@joshuaeacott4226]

If you ever occasionally get the smell of fuel as you're driving, or you get the smell of fuel in the cabin when you've filled it to the brim, then you could have a leaky o-ring, best of replacing it, or you can get fuel resistant silicone, and silicone seal it.

[@MotoringBoxTV]

No smell luckily. The new pump came with a replacement seal, but in my haste I forgot to use it. Have kept it on hand incase I need to ever swap it out.

[@joshuaeacott4226]

@@MotoringBoxTV Fantastic news. Something new players forget with fuel pumps is that seal, a customer dropped it in the tank, and had fuel pouring from underneath his car everytime he filled up, $20 seal, 15mins and he was stoked.

[@warrenballard8729]

Wish the the BA Ute was that easy... I had to take the full well body tray off

[@daledenton9246]

It still kills me in side we have no more manufacturing cheers for the vid mate 👌🏼

[@paulmcgaw6976]

Love the content. Can feel that 650hp tune coming up soon!

[@Johnopro69]

I love the photo of bogan you as you go past 75kms in the road test

[@MrWilliam.Stewart]

Always a good video when Shorno makes an appearance.

[@josemanuel5749]

1:37 - Instructions unclear, I did it while pumping gas.

[@AJ-zv9tn]

Help I took my fuel pump and sent it to Zimbabwe why doesn’t my car work anymore I blame motoringbox

[@munnsie100]

Loving the jokes, and Dr Phil. I’m doing this to my EB wagon soon, I also have to bend the float arm as the tank fills but never reads full on the gauge (tried it with different clusters too). I drove it on empty for ages and it took 48L (it’s a 72L tank). When the bowser clicks off, my gauge reads full and then drops back down to just above 3/4 immediately.

[@TheIronRaven]

Every other channel: Let's recap from the good times we've had, ran out of ideas... MotoringBox: We're just getting started!

[@chrisbenton3365]

The base of the fuel pump/sender is sprung loaded to "calibrate" the sender for different size tanks, so they can use the one assembly on many different vehicles. BMW do it the same way also. Glad you didnt use a cordless drill to take out the screws as the sparks from the electric motor brushes + petrol fumes = boom!

[@MotoringBoxTV]

Yup I was very careful with it, even kept the lighting and camera quite a distance away.

[@ravenc703]

i've been subscribed since your AU falcon video and i've just gotta say i'm loving the frequent uploads mate. i realise it isn't realistic to make your longer vehicle showcases/specials too regularly, but i'm personally really enjoying the cheap as chips and quickie videos (not to mention the longer maintenance videos we've been seeing on the BA). i'm saving up for my first car now, and these videos are definitely gonna be a great resource for me - especially the budget cleaning videos lol. keep up the great work mate!

[@joshuaeacott4226]

Delphi do OEM parts for ford, and the stock one i believe is delphi, i think its a 165 LPH flow.

[@kierantodd9271]

cheers for the video mate done mine today and saved myself a couple hundred bucks 👌🙏

[@ut2k4wikichici]

Had my au burn 3 out thx great vid Gonna put a bigger one in and fix myself

[@MWRB93]

Loving the videos bro 😎

[@bradhouse4649]

Great vid mate! Very helpful.

[@glennt69lol]

The highlight is the primal inner Aussie bogan cracking a smile when the boost comes on 😉

[@Levent_Ergun]

That was a lot of fuel in the tank, when does that light come on? 15 liters to empty? Lol.

[@MotoringBoxTV]

No idea, the level did surprise me though. The needle was only 2mm or so above the empty line. I think if you tried to change it at 1/4 tank you'd be in trouble! I think the tank goes up behind the back seat in a bit of an L shape, so that sort of explains it I guess.

[@VX3800]

Sounds killer

[@Noelly1980]

Great video bud once again. I thought Bosch would have been the standard fuel pump supplier, but I see people have commented with Delphi. Good to see her running well man. Good work. 😉👌

[@robertarchbold8658]

Have you checked the gap on the spark plugs? If it's been tuned and the spark plugs aren't gapped there's a chance it's blowing the spark out. Happened to my FG at high RPM. Genuine plugs gapped to .7 and all good!. edit: I should have watched the entire video before posting haha. Good fix!

[@MotoringBoxTV]

Have a set of NGK Iridiums at .7 in there 👌

[@robertarchbold8658]

@@MotoringBoxTV I replied without finishing the video 🤦‍♂️

[@Leosarebetter]

Just a heads up... I had a car a few years back and I asked the mechanic to fill in the log book, now, there were a few gaps over the years in the log book (it was second hand) and what I was thinking was for him to fill in the actual service that he had done on that day, but he went and stamped and filled in about 3 years worth of log book entries/back dated and then finished his work, to him it was nothing... makes you think.

[@MYMOUNTAIN_122]

Curious have you done a video on a fuel sender replacement for a BA sedan?

[@ba.skidderLOCKDOWN]

Do you have a video on how to remove fuel lever sender unit from in the tank

[@appletechlikes7075]

I actually got mine replaced a month ago. I ended up getting a genuine Ford one from eBay for $90 bucks. Lucky as it was the last one.

[@btecpostmaster]

When changing fuel parts remember to turn over the engine with the fuel relay or pump fuse removed to remove any pressure from the lines.

[@MotoringBoxTV]

I have done that before and had a whole bunch of people tell me it wasn't necessary. Didn't bother this time around and it seemed ok.

[@btecpostmaster]

@@MotoringBoxTV it really depends on a couple of things. the condition of the check valve in the old pump and how long since it last was run.

[@hamishfullerton7309]

And e85 compatible pump ,might have been a good idea,(this pump might be enough, ) ,so you had the supply in case you wanted and e85/flex fuel tune so you can run both and changing the fuel lines is overkill and unnecessarily, if the fuel lines handle e10 ,e85 won't have any effect I run it in my au 5.0ltr lpg ute for years with no modifications just to idol on because I don't like smell of petrol fumes ,I have had to change the old fuel pump since thou but that's it. These aren't that expensive or complex from what I've heard and e85 fuel is a great complement to a turbo car because it burns cooler and works well with a high compression environmental helping to stop pre detonation when you up the anti and will give you more horse's . Also has a fruity smell a lot less toxic than premium and you can get it at all United's for around the same price as premium,you do use a bit more, but you could alternate depending on what you using the car for.

[@tturi2]

you can buy a replacement pump just like what you have, except it has a W460 pump pre-installed for you, return hole pre-drilled also

[@queenslandballistics2987]

8:38 Did you hit the limiter in 1st then in 2nd aswell?

[@MotoringBoxTV]

Nope I didn't hit it on either occasion 👍

[@queenslandballistics2987]

@@MotoringBoxTV So it must be higer than just 6000rpm I'm guessing. 🤔

[@MotoringBoxTV]

I always thought it was 6500 but heard 6000 on a few forums. It very well could be, and I just missed it.

[@queenslandballistics2987]

@@MotoringBoxTV Mate you can always find out. Braahhhhh stu stu stu.

[@queenslandballistics2987]

@@MotoringBoxTV Dude you should see if you can make it rev all the way to 7000rpm. Just to make that Barra scream and sing. 😤😲

[@arokh72]

Any chance you could do the spark plugs, assuming you haven't already, since mine need doing and I have nfi how to?

[@MotoringBoxTV]

I've done that a few months back - check out the channel 👌

[@arokh72]

@@MotoringBoxTV I probably forgot, which would be typical of me :)

[@MrWilliam.Stewart]

Send it!

[@MedalForces]

that pumps 100% original! the piggy back system is old and if you where to go pcmtec you will have to remove the piggyback

[@MotoringBoxTV]

Yes... and I don't think that part will be easy.

[@MentalExistence]

Gotta do my AU fuel pump and the other filter

[@markdurl8341]

i wonder why they changed the fuel pump access point, in my old AU, the fuel pump was in the boot under the spare wheel

[@jamessolidairy8134]

Could be worth changing the fuel filter too

[@brett1983]

It loves it 😅

[@SHOCKcustoms]

How many kms on it? Restrictions of old blocked cat also affect these cars significantly. Pop on a 4 inch dump and high flow cat or cat delete. Difference is remarkable even with standard exhaust. Then pcm tec tune the whole package #browniesgarage

[@MotoringBoxTV]

Yup I have considered that too. I will most likely upgrade the exhaust before I ever get it tuned.

[@robbieaussievic]

...... Smash the cat into pieces, who's going to know ? Any restriction is power lost.

[@SHOCKcustoms]

@@robbieaussievic remove it. Smashing is a waste of time and energy. 4 inch take a dump pipe will work.

[@zachooton6036]

hey my gusse would be the spring is connected to the float so the float dont get stuck up

[@MrWilliam.Stewart]

Ya won't bend it, If Ya don't send it. Send it!!

[@Andrew.quigley]

Nice result. You going to up grade the ICC to the premium version in the future?

[@MotoringBoxTV]

Probably not, it isn't just a straight swap by the sound of it because you're going from single to dual zone.

[@memphis9787]

Cheers mate, nice and clear steps and vid.

[@Raith_05]

2 uploads in 2 days? Hell yeah

[@jsd9871]

I remove my Ford AU fuel pump retaining ring with an almost full fuel tank I didn't end up in orbit and the boot was full of fumes and I was using an 18 volt rattle gun to shake it loose whenever on playing with the fuel systems I always wear flame retardant clothing you never know when you'll be barbecued by a Flashfire

[@martyburgess341]

Gets up there fast! Maybe the valve springs need attention. I dare say you may not wanna do that yourself. But might worth looking inro

[@jul5498]

Where can I get the fuel hose removal tool?

[@BATJINSTER69]

Hey man what are you going to do with the old sending unit?

[@SRY4.0L]

do you use 98 premium petrol

[@MotoringBoxTV]

Yup always.

[@silvernoob1603]

i wish the falcon wagon was as easy to change as this......

[@alpharaptor7510]

The BA/BF is similar to a AU Falcon but the inside and the front and rear are different and the fuel pump is in different spots

[@agent_soshi]

8:25 looks like a pretty popular spot you’ve got there

[@MotoringBoxTV]

Yes.... popular to some.

[@joebelichio6974]

Have u got a link to where u got them fuel disconnect tools? I have a Territory with the same type connections but have to drop the tank just enough to undo the connections without pulling on the electrical connector so it's a very tight fit. Any help with what type of disconnect tools work would be appreciated

[@MotoringBoxTV]

Got them from Supercheap from memory!

[@mahcooharper9577]

Haven't finished yet but it could be hitting boost cut if changing the pump doesn't fix it...

[@MotoringBoxTV]

It runs higher boost and a piggy-back ECU, which basically means the stock ECU sees nothing wrong. So the pump basically fixed my issue, but as per the pinned comment I do think the car should be faster than it currently is. It probably all comes down to the tune, but we'll see what happens.

[@mahcooharper9577]

@@MotoringBoxTV eeeexcellent. :)

[@Dredge315]

I didn't have the 3rd line in the middle when I removed my stock pump so now I'm confused

[@deanxmfalcon6451]

Nice video How has the pump set been I’m gonna do the same but get the 1litre swirl pot from sniper to stop the fuel starvation at higher rpm

[@MotoringBoxTV]

So far so good - no issues with starvation yet, but then again I tend not to give the car a hard time if the fuel level is getting low. Keeping it over half if doing track days etc is always a good idea.

[@deanxmfalcon6451]

@@MotoringBoxTV that’s good news I’ve just purchased a BA xr6 Turbo And have noticed the fuel starvation is worse when the fuel is lower Keep up the great work with a Videos

[@CentralCoastBoyz]

Hey mate, Have u got a link for a NA FG pump that you would recommend?

[@jesseteichmann2397]

Can you access the pump this way on a 2010 territory? Every other video they drop the whole tank

[@MotoringBoxTV]

From what I've heard the tank has to be dropped on Territory's.

[@cootason]

Might have to get a new fuel pump for my AU falcon as well peace of mind really isn't it.

[@hawkboy4]

The ebay link you posted says its for sedans only. Do you know why they arnt suited for use on utes?

[@MotoringBoxTV]

Different tanks on the utes, but there should be a suitable one on there somewhere.

[@Kitcat8357]

Hi brother, thanks for this video. Sorry just question, if i put the same fuel pump in my xr6 turbo ba, 4 speed auto, do i have to tune my car, because my car already has been tunne . I'm not looking to increase any power, or it will effect my tune, ?then i have to tunned again because new fuel pump, thanks heaps for every single video you do.

[@MotoringBoxTV]

No you won't need to get it tuned!

[@stuffedgrubs]

Would this be what I need to do for a fuel gauge reading empty when it's full

[@MotoringBoxTV]

From memory when I removed the pump there was a wire inside the tank I had to disconnect from the pump, so that must be for the fuel level sender which sits inside. That's about as much as I know! So yes, separate to the pump, but does connect into the pump wiring.

[@lisanikkelson761]

Just wondering where you got the clips from

[@MotoringBoxTV]

To remove the fuel lines? SCA I believe.

[@ThePowerbloke]

Another excellent video mate. Great to see it did give some good results. Thanks for sharing. :-)

[@Tayeedz1]

Goddamn I wish we got the BA Falcon in South Africa. This sounds like class & goes like spit

[@matt_hayward]

Hah get one of the older falcons you did get in ZA and install a Barra turbo in that. It will go like the clappers, as those old EL(?) Falcons we exported over there were significantly lighter.

[@knight2425]

Wondering if this thing has had any mods seeing as it’s tuned it might just need of a bigger pump but Fords are not my thing so not sure

[@MotoringBoxTV]

I don't think it has. The only thing left I'm not sure about are the valve springs. But I'm guessing they're stock too.

[@tcpnetworks]

It could also be the filter... That's where I've had issues.

[@MotoringBoxTV]

I did the filter about a month ago, but may swap it out again in the near future just for good measure.

[@firstworldproblems6064]

hey man i put in a walbro pump with the upgraded assembly on the fg but also put in a evc throttle controller same time. does the assembly have to be pushed down in all the way cos mine was very springy and also does the black ring have to be turned down all the way? im havign some irregularities when coming to a stop its dipping sometimes but i think its the touching/changing the throttle controller while driving or its the pump. the car has been starting much smoother since the new pump. i also notice now i have had a 6 speed zf conversion the car runs bit warmer closer to middle temp alot. p.s. shes quite fast for a non turbo i tell you. running on 98 all the time n that

[@MotoringBoxTV]

Mine did have to be pushed against the spring so that I could get it sealed and screwed back in properly. That sounds like a weird issue because coming to a stop the engine is pretty much at idle so it'll have more than enough fuel to do that, the issue would unlikely be the pump I think. Half temp is fine that's where they usually run at 👍

[@firstworldproblems6064]

​@MotoringBoxTV okay brother ive re installed my old pump and assembly car seems great. think I'll be asking for my money back. ugh.

[@whstato0212]

Aha love the thumbnail bro. Thats crackup

[@corywatts80]

My man did this video out at swanbank

[@MotoringBoxTV]

Boral strip

[@Nigel_noongar78]

Wouldn't they be motorcraft from stock

[@qam2878]

I was surprised Delphi was the OEM supplier as I've seen their name more on GM products not surprising as they were part of GM but were sold off

[@stephenmarr7185]

Holden are usually AC Delco.

[@MrSamskelly]

i only replaced 1 fuel pump and it was the worst thing needing to drop the tank

[@jamessmith4681]

Hows the pump going now?

[@MotoringBoxTV]

Still perfect.

[@aaronsmith5154]

I have a ba Falcon 1 ton UTE I have a leak in one of those hoses connected to the fuel pump does anyone know if it's possible to get to the pump without removing the ute tray

[@MotoringBoxTV]

From what I've heard the tray does need to be removed, or unbolted and pushed back far enough at least.

[@aaronsmith5154]

@@MotoringBoxTV Yea I thought that maybe the case thanks for replying 👍

[@huh2634]

Still waiting for you to buy a ba xr6 ute m8

[@SHOCKcustoms]

Next mod 1150cc bosch injectors

[@nick307gt2]

BA XR6 TURBO 🪑's

[@xr88yu]

Delphi part number 25355031 stock pump on XR6 turbo.

[@aft-fishing90]

Does a full tank of fuel last you a week?

[@MotoringBoxTV]

Depends how far you drive per week. This car only does 150km max, so yes easily.

[@aft-fishing90]

@@MotoringBoxTV I'm picking up a BF Fairmont Ghia and some people are scaring me that they're so thirsty. Just wanted to ask you first, since I'll be driving it to work and back. 80% of it will be highway mileage.

[@MotoringBoxTV]

You'll probably get 10 - 11L/100km. Driving around town blows the figures out a bit. In the end they're still relatively cheap cars to buy. Better than spending 20k on a Corolla just to save a few bucks at the pump each time.

[@aft-fishing90]

@@MotoringBoxTV thank you for the information, it's my first Ford and finding it in good condition with only 147,000km on the odo at a good price lured me to it. I oftenly do long distance trips for fishing and can see it'll be comfortable to drive in. Are parts to it easy to install? Correct me if I'm wrong but the car looks easier than most cars out there to work on yourself.

[@MotoringBoxTV]

A lot of basic maintenance is pretty easy, there's a lot of access space around most areas of the engine.

[@doug-core8850]

You just made that look too easy

[@petertomkinson1869]

I will NEVER EVER buy a replacement fuel pump for the Falcon with the brand name FUELMISER supplied by "MOTOSPECS" Australia, Glendenning, NSW, through Repco (Model FPE-355 EFI Fuel Pump). The workshop fitted one that stopped reliable quantity indication in about 8 months, the second lasted longer (maybe 18 mths) but now failed also. Cannot say I thought the FUELMISER brand spark plugs set I tried was much chop either, quickly replaced. MOTOSPECS claimed in a lteer the fuel deterioration was at fault but the BPO info sheet supplied did not support that claim at all. MOTOSPECS did say they would refund the pump price but I have never seen a hint of money anywhere so probably BS hot air.

[@milanbachraty4630]

I stoppd watching when the screwdriver came out. Boy o boy

[@pauljohns8215]

Hello hello hello

[@nickg4135]

plastic fumes yesterday and petrol fumes today. your lungs must hate you

[@MotoringBoxTV]

Same day 👌