Chinese Diesel heater quiet pump project

[@vancey6072]

Surprising there wasn't better results. I would've bet that would wrork. A big thumbs up for all the work!

[@MrMeltedwellies]

Thank you and thanks for watching

[@jaybee258jb]

Thanks for the thought provoking video. I think much of the noise it due to the pipes tapping on the case and other rattles. I have a similar heater and I love it iny small van I got some bitumen car body sound deadening sheet and stuck it to every flat surface I could find within the case. Also wrapped the pump in it like you did. I did away with the rubber bracket and wrapped the pump in strips of Karimat foam and just jammed the encased pump into the space. I put this soft neoprene like foam sheet in all places where pipes touched the case. It's a lot quieter and the ticking is a soft dull tone. Acceptable but I'm still looking for ideas. Potting the pump in silicone is my next idea but I'm looking for examples first. Nice video thank you for your efforts.

[@curtwuollet2912]

I have been meaning to pick up some duct seal, the stuff like heavy duty modeling clay. I think embedding the pump in a pound of this would provide the mass and absorbtion to quiet the pump.

[@raywhite5523]

Hey, 10 out of 10 for trying. You sounded a little disappointed don't be you tried something. Nothing stopping you trying something else. Ingenuity is to be applauded, as I said 10 out 10. Thanks Ray

[@robertyoung2229]

The tape is called self amalgamating tape...good stuff

[@andywells397]

Try a softer insulation material , mount the pump outside in a insulated box . Make sure you use thick material. Do not mount it on the case. The rubber you used is to hard and as somakes little difference. Good video though, shame it was not as good as you inticipated it to be.

[@MrMeltedwellies]

greats tips thanks for watching Andy

[@Bennytet]

Great idea using the box but if you had used acoustic wadding or quilting rather than hard rubber it would improve the sound reduction hugely. In the example here the pump sound transfers easily through the rubber to the outside box and onto the outer heater casing so not much if any change. Enjoyed the video and thanks for posting

[@MrMeltedwellies]

Thanks for the tip!

[@MHLivestreams]

Silicon works well. It's possible to run these with no pump, just needs one to start or there's an error code. Measure the flow properly and it's no problem, totally silent.

[@georgeda90]

​@@MHLivestreams What do you mean measure the flow?

[@MHLivestreams]

@@georgeda90 should have said fuel rate. To calculate the fuel used when operating by pump.

[@therealchayd]

My Dad had some success quietening the noisy pump by wrapping it in neoprene foam, then dangling it from small rubber bungies which helped isolate it from the heater body, I mean it still clicks but not much of the sound makes it from the pump to the rest of the heater. The weird thing is, I've got a Japanese paraffin heater which uses a similar solenoid dosing pump, but for some reason that makes no discernible noise at all.

[@MrMeltedwellies]

Thanks for watching and comment

[@dr.phelps]

Parrafin might be thicker and thereby dampening

[@1allan2]

I did this using roof and gutter neutral cure silicone. It was a layer about and inch thick around the pump body, once cured clamped in a box similar to yours and its barely audible. Problem solved!

[@colinpowell4788]

Please post a video of your silicon solution. If your solution works as you claim you will get thousands of views.

[@CanadienNortherner]

Maybe cork would work , but seen many try without success . The craftsmanship was 10outa10 👍

[@MrMeltedwellies]

Thank you and thanks for watching and comment

[@brendn1264]

you are on to something with the aluminium case that's perfect!!!

[@medeiros3610]

Thank you. I wonder if rubber shock mounts would help any? Going to purchase one and that noise is my only concern. 🙏👍

[@MrMeltedwellies]

It should

[@neilmac4730]

Question, what do you think of filling the box with expanding foam instead 🤔 OH, and Merry Christmas 😊

[@MrMeltedwellies]

well i have heard that so i was going to give it a go merry christmas and a great new year

[@Djamestm]

Thumbs up for trying this. I wish it would have worked out better for you!

[@steveriley1000]

From what I do know about soundproofing. You may have two issues . One is the rubber you used is probably still allowing the vibration from the injection pump transfer to the outer metal case . The other issue is the plastic plug is touching the plastic housing when you put the lid on , that allows the vibration to transfer to the plastic box . Also same with the hose ends . Might I suggest trying to use sound dampening materials for example put it in a box that is twice the size of the plastic box and use cardboard egg cartons on the inside walls of the box then find a block of soft foam to mount it too inside the box , run the hoses through that box without touching the sides of the outer box but through some soft foam . It won’t fit inside the metal container but it should still be as quite or better .

[@MrMeltedwellies]

Cheers Steve will give it a go

[@caretakerfochr3834]

I wonder if you might get a better effect by building the pump into the box and filling the cavity with spray foam?

[@demolitionbmxd]

I know this is an old video but from a sound engineering perspective I would try wrapping the pump in a butyl type tile for automotive surfaces, then encasing with a fair amount of closed cell foam and lastly a mass loaded vinyl.

[@philipraymond8377]

Try closed self foam insulation like you use in HVAC. It’s black in color and you can get it in different sizes. You should be able to simply wrap the insulation around it and zip tie it to keep it closed all done, faster and cheaper.

[@AquaTech225]

What I did was bought a silicone mold making kit. One that xxx toys could be made of soft. An taped the hose ends. And the plug part. An just got a Tupperware container. And encapsulated the pump. Than with a razor blade. Extracted to my tape areas to expose the plug an each hose end. Plugged it up to the hoses an plug. An just stuck it in the heater an closed it up. I didn’t worry much about the pump getting to warm due to its electrical workings or what not. Due to when it’s used it’s cold in general. An never has an issue. So it’s kinda floating in its lil spot inside the heater inside of a soft silicone block

[@MrMeltedwellies]

Now thats worth a go thanks for info

[@castorpollux3752]

Play Dough or modeling clay is much easier.

[@frederick6008]

The back panel of the case that the pump is bolted to is vibrating causing the noise. My pump is attached to the frame of my ford e250 with the rubber holder. She's quiet as a mouse.

[@chetmyers7041]

13:38 Pump still pounds like E. A. Poe's "Telltale Heart." I wonder if some of the sound comes from the plastic tube.

[@raywhite5523]

Ps. Maybe try a less dense sound absorbing material. Like a modern rock wool material, you can get fireproof/ heat proof versions. The rubber you used maybe transferring the noise more because it is so dense, also van sound proofing. I am thinking of getting one,and I am thinking like you of the noise. Keep on thinking spot on. Ray

[@jamesmason7124]

Just thought I'd mention that the muffler should be mounted vertical with the drain hole facing down and the lowest point of the exhaust system

[@kroozer5215]

wonder if filling the box with expanding foam would help, its what thieves use to do with alarm boxes

[@johnkillick6061]

Would expanding form work?🤔

[@TrevorBoughtABus]

Now it sounds like James Bond's PPK in Dr. No! 😂 Great experiment. Thank you for sharing.

[@AJ-qn6gd]

Buy an Eberspacher pump, in the blurb for our heater it describes the pump as “near silent” ours is mounted underneath the van and I can honestly say I’ve never heard the pump either Inside or outside the van. Hope this helps someone.

[@scousebikers]

Do the pumps need sealing in a box or something under the van I worry about rain water etc

[@AJ-qn6gd]

@@scousebikers I think the pump is alright it’s the circuit board in the Chinese heaters that is not sealed against water and hence it’s vulnerable to water ingress.

[@scousebikers]

@AJ-qn6gd oh yeah that's no problem that's inside I am just rerouting fuel lines tommorow hopefully was using a auxillier fuel tank but it started leaking inside the van what about the connection to the pump surely that's not watertight??

[@AJ-qn6gd]

@@scousebikers the electrical connection should be an automotive quality connection with a small rubber seal in it and snaps together like engine sensor connection not heard of any problems with the pumps, mine is under the van and no issues whatsoever.

[@scousebikers]

@@AJ-qn6gd ahhh perfect I'll have a look to be honest I didn't think but it makes sense that it would be waterproof with it being for boats cars etc

[@wrxs1781]

To start, buy an upgraded fuel line kit, run the pump in a vertical orientation. As long as the pump no matter what the insulation is affixed to a solid percussive object you will hear it. The rest is easy.

[@golddetector01]

One of the reasons I do not go for the all-in-ones because you can get rid of the pump noise place it in a better case with extra padding.

[@mrlecuk]

it's knocking like a bailiff😮

[@frankc6430]

my theory , the softer the materials you use to wrap the pump it dampens the clicks (neoprene) and a hollow or light hollow or less solid materials for the box (foam).

[@karenmcnolty9208]

Love your work on making this unit quieter, been wearing ear plugs! I see wehave the same unit. Any tips on how to pair it with the remote? Finding the included instructions a tad confusing!

[@bernardmauge8613]

You need rubber mounts from the box to the sheet metal. the sound is amplified by the sheet metal try not to mount the box with bolts just hanging and check for noise level.

[@MrMeltedwellies]

will do thanks for help

[@gangiolini6201]

The tank is above the burner…Do we even need a fuel pump? Gravity should feed the burner…or am I wrong and is there some sort of injector that needs pressure in there?

[@librulcunspirisy]

The pump meters the fuel.

[@mijodo2008]

Try a Decibel meter at a set distance before and after. Try encasing the pump in a softer medium ie. foam rubber. Bear in mind any hard surface in contact with the sound source will transmit sound. interesting video though.

[@gordondonald1955]

I just purchsed a 5kw heater, it looks very near the same. Mine is much more quiet!

[@glennr9913]

Your exhaust extension may not be safe. I don't think you're supposed to extend the small pipe so far. It would probably be better to increase the diameter to run farther than the stock exhaust pipe length.

[@paulbeddows6014]

Have you noticed it getting.louder when the fuel gets below quarter full

[@MrMeltedwellies]

No but i probley will now lol

[@Supercarlsunday]

😂😂 Its not much difference, fair play for trying. There an absolute nightmare 😫 specially when trying to sleep in your van. Like Chinese torture 😂

[@MrMeltedwellies]

😂👍

[@mperdue12]

The best way to get over this noise is freezing cold.

[@MrMeltedwellies]

LOL

[@steiny3353]

That's right . If it's cold enough and the heater is actually HEATING,,,,,you won't give a rats 🤣

[@americantruckeringermany8394]

i dont understand why people dont materials dedicated to sound deadening, such as foam. the hard object will vibrate the sound you need to dampen it

[@paulbeddows6014]

Encase it in silicon sealer and use silicon to stick the box to the heater. But be careful with the electrical contacts as silicon setting gives off fumes which cause steel to rust so I would wrap the plug with insulation tape. Or encase the pump in black dense foam two halves shaped to fit the pump snugly

[@MrMeltedwellies]

thanks Paul

[@paulbeddows6014]

@@MrMeltedwellies don't know if expanding foam would be better or worse to encase the pump.

[@AquaTech225]

That’s exactly what I did. Bought a really soft silicone that I looked up could be used for xxx toys. An a small Tupperware. Taped up the hoes ends an plug. Encapsulated it completely and with a razor. Carved out to the important areas. An just hooked it up in the heater with it floating in its silicone block

[@skippercaship]

You would be beter filling the box with expanding foam (maybe) give it a go and make another video please

[@MrMeltedwellies]

I'll have a look

[@davidsavage4741]

How about this.... Yongle Elliott ET950 Noise Reducing Cancelling, Cloth Adhesive Friction, Wire Harness Fleece Tape, High Temperature 220F, 3/4" X 25M FS

[@steveriley1000]

Good video btw 😊

[@grumpygrandpa3640]

What about using an off cut of sound deadening foam wrapped round it then stick it in the box 🤷🏻‍♂️

[@MrMeltedwellies]

Good point Grumpy might give that a go

[@mperdue12]

I have one and a buddy of mine has one and can't get over the thumping so he put it in a coffee cup and sprayed GreatStuff to fill the cup. It works pretty good for the effort. Id say 60% reduction. Pulling it off the back panel has to be a tremendous improvement.

[@dwfmedia]

Nice try though, well done. One day someone will have a solution and we'll all be happy... Evolution of the Chinese heaters haha.. Thanks for the video

[@MrMeltedwellies]

Thanks for watching

[@regd.2263]

Try high density foam instead of hard rubber

[@ArgosWarrior]

fill the box with expanding foam

[@randall1959]

Reminds me of an Edgar Allen Poe poem.

[@charlietango1635]

Sorry Mark, but I don't think it is any quieter, but still enjoyed the video

[@MrMeltedwellies]

Your right Charlie thanks for watching

[@jackcat550]

Should have used foam or styrene instead of the rubber.

[@americantruckeringermany8394]

i watched that whole video to hear some crazy thumping noise in the end. jesus christ

[@MrMeltedwellies]

lol thanks for watching and comment made me smile ATB

[@BeyondWrittenWords]

Just tell your mates postman Gerry is visiting the lady of the house again

[@tecnology-today]

there are two fails that makes the whole invention totally useless: the ends of the pump are tuching the plastic box, AND the plastic box is touching the main case through the bolts. My friend, unlike the thermal isolation that admits some looses from thermal bridges, the mechanical vibration isolation REQUIRES a TRUE mechanical TOTAL isolation! Make the pump "floating" in soft foam and you will success

[@MrMeltedwellies]

Thanks ill give that ago

[@darrincambridge2377]

Or pipe lagging and sound deadening pads ☺

[@rodbtelenetbe]

Acoustic foam and rubber net to hang the pump in and noise tik is gone

[@mickkelly2229]

Hey mark some one knocking at your door

[@Roscoadventures21948]

The pump might be noisey at lest u no its working

[@danielpiche6759]

Mount it on rubber between the body

[@minthos4045]

sink the whole pump under silicone glue

[@MHLivestreams]

Silicon definitely works.

[@dtwistrewind7361]

Fill the box with sillicone

[@jrperrotta]

Ha ha failure! Do you know how to make silicone putty? Wrap it with that in a bag casing

[@flpalacios9633]

There is a silent pump on the web market

[@mikemorris3545]

A word of warning you have fitted your exhaust muffler indoors, these are poorly assembled and leak carbon monoxide fumes plus there is a moisture drain hole.

[@alexandermunro7711]

Exhaust is the wrong way round.. Breather hole should be at the bottom

[@Sydney268]

Least of his worries when he has the silencer inside the building!

[@ronaldmilligan63]

Didn't work

[@LFANS2001]

Watch this video and notice where the fuel pump is installed (outside of the case) and an improvement on fuel lines. In this video you can't hear the pump at all. kzbin.info/www/bejne/nX-uhY2lqLFpmpo

[@flpalacios9633]

You have a good drummer for free instead of a pump

[@frederick6008]

Tell Tale Heart, by Poe

[@Fual4eva]

This video may be of interest to you, i've seen many suspend pumps like this using strong elastic and it does make quite a difference, the only problem is you'll have to mount the pump outside the case. hope this helps in some way kzbin.info/www/bejne/qIGWd4KGptl8hMk

[@steiny3353]

George M ..I'm researching tricks for when I buy a diesel heater for my small caravan, (17ft.Oasis)and when I saw your link, wondered if it was the one I had already watched, and it was. I think I will settle on this one (in your link) as it seems to have the most feasible explanation for getting rid of the vibration noise. The elastic suspension shouldn't transfer any vibrations and the insulated box should get rid of the rest of any noise. I'm thinking about installing it in the front boot of the van for easy access (I'm partially disabled) with a removable fuel tank so as not to risk spilling diesel, and having fuel filter and pump where it will be easy to change when necessary. I could even mount the pump and filter on the A frame of the van, out of the way.

[@madeleyinc]

Yeah, didn't work.

[@-freespirit-3314]

Fill it up with sand.

[@d71mau]

To silence the pump suspend in a plywood box lined with roofers lead sheet = Total silence

[@MrMeltedwellies]

cheers ill give that a go

[@purebloodedpatriot9352]

Set the pump at 90 degrees with outlet pointed up.

[@gedtoon6451]

I would call that a fail!

[@MrMeltedwellies]

yep

[@Snailmailtrucker]

It's a lot better than your video !

[@oojimmyflip]

the only way to beat this is to hang the pump from a frame on fishing braid. may I add that the exhaust recomendations are no longer than 2 meters in length. and the green fuel line puts extra strain on ther pump as it gives and expands each time the pump pumps making the fuel injection less effective, almost everyone replaces it with the hard 2mm core nylon fuel line that doesnt expand as the pump pumps. There are also no fuel line clips on the fuel hose another saftey issue to note. the green fuel line has been known to perish and split esspecially around the exhaust outlet, this could cause a fire. you will also need a fuel filter installed before the pump, most heaters come with one. as you have it set up I honestly wouldnt put it a family members house without at the very mimimum doing these saftey upgrades. and please make sure you install a carbon monoxide alarm. some titanium exhaust wrap double layered may also be advantageous to keep the hot exhaust from damaging the fuel line or to protect the hands of little ones if they should grab it? it is available on Amazon.co.uk or ebay. you can also searh either site for the Diesel Heater fuel line upgrade kit it costs about £12.00

[@MHLivestreams]

Use a wider bore for longer exhaust lengths, no problem.

[@velocity800]

pretty failed

[@MrMeltedwellies]

Fun trying Thanks for watching

[@Handleyman]

Sorry but I’d call that a 100% fail.

[@MrMeltedwellies]

yep and me

[@brendn1264]

its worse bro sorry

[@brendn1264]

you are on to something with the aluminium case that's perfect

[@hikurukutai]

haha, you made it worse

[@fishandreptileinfo]

Nice try.

[@MrMeltedwellies]

Thank you and for the view

[@alfsuajua]

hahahahahahahaha

[@intrusivenature9758]

Fail, end of

[@Timetraveller1010]

Flop. 👎