How to fix bicycle vibration. The bike became like new !

Рет қаралды 34,148

Nice Bike Service

Күн бұрын

Пікірлер: 44

@seraphan6 Ай бұрын

Really great filming. It's exciting to watch. This seems like a frustrating bike to fix, though.

@robertmcfadyen9156 Ай бұрын

4:00 , as standard socket set can do this with an extension bar if required . I have 600 millimetre extension bars . This method is much easier .

@velobike7 Ай бұрын

Hi, first vd-40 and then heating, is it more effective? than just heating? 2) what did you measure in the new chain with a ruler? 3) why do you need to break the chain of the new and old?3.34min 4) How did you find out how many links of the chain need to be removed? usually you need to skip the chain without a switch and plus one link. Thanks for the answers, well done

@threeDeeBeginner Ай бұрын

1) yes, anyway you must try with wd40 before using heat 2) it's to show us the stretches at different places 3) to ensure you don't have tight spots on the new chain 4) Shift the Chain: Place the chain on the smallest cog in the rear and the largest chainring in the front. This is known as the "small cog, large chainring" setup. Check Derailleur Alignment: Look at the derailleur pulleys (jockey wheels) from the side. For correct chain length, the pulleys should form a straight, vertical line perpendicular to the ground, ideally creating a 90° angle. This alignment indicates the chain has the proper amount of tension without being too loose or too tight. Adjust as Needed: If the pulleys are angled or not perfectly vertical, adjust the chain length by adding or removing links until this alignment is achieved. Test Shifting and Tension: After setting the chain length, test shifting through all gears to ensure the chain moves smoothly across the cassette and does not put excessive strain on the derailleur in any gear combination.

@anonymously241 Ай бұрын

Congratulations 👏🎉 my friend

@NiceBikeService Ай бұрын

glad to be of service! thanks for your feedback 😘

@threeDeeBeginner 5 күн бұрын

6:51 by adding lube on this screw, you would have far better preload so it won't move in long term.

@F_youtube_rassist_cencure Ай бұрын

1:26 i like this classic sound :) mechanic uhu: "another bike with owner who dont care abous service culture"

@NiceBikeService Ай бұрын

but there is work)))

@Luca-nx5xf Ай бұрын

Hello there! Great video as usual, but isn't the chain a bit too long at the end? As in the derailleur should be more extended outwards? Thank you

@NiceBikeService Ай бұрын

Thank you for your comment. The length of the chain is fine, in principle, you can remove one more link, but it doesn't matter. When the chain is inserted, the derailleur stands without tension, so it looks unusual

@robertmcfadyen9156 Ай бұрын

@@NiceBikeServiceThe bottom bracket installation procedure wasn't shown including noise level before and after .

@robertmcfadyen9156 Ай бұрын

@@NiceBikeService7:25 , the pedals weren't very smooth .

@robertmcfadyen9156 Ай бұрын

@@NiceBikeServiceFreehub service . I do them frequently .

@СерегаСержио-ь5э Ай бұрын

Смотрел на одном дыхании...🤩👍

@cincofr7079 Ай бұрын

Your work is so wonderful 🇲🇦👍

@NiceBikeService Ай бұрын

Thank you! 😊

@threeDeeBeginner Ай бұрын

to tight the quicklink it's easier to backpedal so the quicklink is on the upper side of the chain, at that point you only have to push the right pedal with your right hand while holding the rear wheel with the left hand, and you'll feel the click.

@Mr.Leeroy Ай бұрын

lol, that's like 4% elongation

@Gromitdog1 Ай бұрын

That old chain was really stretched. Perhaps the owner needs to invest in a chain cleaner and some lube.

@Felintrepid Ай бұрын

Perfect job!

@blackIwaterIpark Ай бұрын

Dobra robota = oglądalność kanału rośnie. 👍

@MoeinBayat-v8q Ай бұрын

Good job 👍❤❤

@Kacavida11 Ай бұрын

Crocs for the win, nice job, p.s. I hate that powerlink

@nicholaschai4458 6 күн бұрын

do you have a how to service a shimano alfine 8 igh?

@anka2866 Ай бұрын

Ok. Tylko wydaje mi się, że nie docisnąłeś do końca dźwigni na szpilce QR. Sprawdź jak możesz jaki ma zakres dogięcia.

@Mohamed-zy7yt Ай бұрын

1/4 ball bearings Where can I find it?”

@NiceBikeService Ай бұрын

In Chinese marketplaces, in bearing stores, in online bike shops😉

@mohamedblanco7719 Ай бұрын

mais tu as changé tout quoi hhhhhh j'attendais un tour de magie

@LeRatonLaveurRayer Ай бұрын

comment tu peux peux mesurer/tester si la cassette ou pédalier sont usés ?

@threeDeeBeginner Ай бұрын

tu le vois à l'usure des dents. En général c'est d'abord la cassette qui s'use, le pédalier est généralement d'un alliage plus solide et surout il répartit les efforts sur plus de dents, ce qui ralentit beaucoup son usure.

@makantahi3731 Ай бұрын

a worn chain has a larger pitch than a new chain, that's why only the tips of the teeth are worn, which when new look like a U and when worn look like a V. the best indicator is if the chain skips, but only on the cassette, because the chain almost never skips on the ring gear, it should be completely worn

@LeRatonLaveurRayer Ай бұрын

@@makantahi3731 merci

@kylam9874 Ай бұрын

Awesome !👍

@Gabbro.88 Ай бұрын

Ottimo lavoro

@Testbug-dy6tj Ай бұрын

👍💪, nice

@NiceBikeService Ай бұрын

🥰🥰🥰

@CSKang-fe1py Ай бұрын

체인이 긴거 같은데 엄천 출렁거리네

@agustinvaltierra6135 Ай бұрын

This Video is for Profesional experts, no gives explanations of anything. If One amateur do it he’ll Make so many mistakes and waste his money and Time.

@threeDeeBeginner Ай бұрын

right, but it's pretty the only one to do this. His moves are nearly perfect.