Ninebot Z10 Tire Pressure and Filling The Tire

[@3euc]

Thanks for the tips. I just bought a set of Slime valve extenders from your link for my Z10.

[@TheOnlyDaltonGang]

Really appreciate the heads up on the valve stem extension.

[@daggyag9613]

You probably need to secure the first and second valve to each other in case you screw it off leaving the first valve behind still attached to the valve of the tube. Otherwise, thanks for sharing Marty! Best wishes from Singapore to all the EUC riders over there, cheers!

[@barlscharkley5411]

Thanks for the tip on the valve extensions. I, also, was a little worried about dealing with air pressure in the Z10 after seeing Chooch's struggles with the Ninebot E+ valve extender he was using. At least I'll have valve extensions on hand if and when my Z10 arrives.

[@MrJbchocolate]

Totally agree. Tire pressure is function of rider’s body mass without buts about it. Needs to be explored and tweaked by the rider on particular wheels....a cast in concrete given pressure is just incorrect. Also, Thank you for sharing the extension....truly clever, Marty.

[@knifesketch101]

Great video Marty! Thanks for these tips.

[@ghostman0234]

Good Video. Thanks

[@mightron]

Hey, I'm using the exact extensions you got but air isnt getting to the other side, just bought these. how much do you screw it down onto the z10? Mine have a red o ring inside. Maybe I overtightened them?

[@ElectricUnicycles]

Everything is firmly tightened on mine. Not sure what could be wrong.

How do you remove the valve cap?

[@ElectricUnicycles]

There is no valve cap

Interesting. Mine is original and has one.

[@ElectricUnicycles]

@ My original did not. You've had the wheel since 2018 and you haven't had to put air in the tire until now??? A long needle-nose pliers should be able to remove the cap. Good luck.

I have it since 2021. Thanks for the tip

[@sautsitumorangkpk]

thanks mate ,

[@uwekatz5345]

THX for Video, Do you know how to reset the wheel to factory settings?

[@ElectricUnicycles]

Unfortunately, no :-(

[@ThatGuy_0815]

Hi Marty! Thanks for the info! What about the pedal height? Is it easy to scratch the pedals in corners? Thank you very much!

[@ElectricUnicycles]

The pedal height is average. However, due to the way that this wheel handles, in my opinion, pedal scraping is a non-issue.

[@ThatGuy_0815]

Thanks! houseofjob said the height is about 5 inch. That seems quite low though...

[@devojunior4007]

I see 3 valves are there 3 or one

[@giwu]

Very interesting! I would suggest using a bit of loctite on your valve extensions, as to avoid when unscrewing that the bottom one is left behind.

[@xorbe2]

This is what I was concerned about!!

[@dubmob151]

Didn't really need to chain that many of them together to clear the recess, but just taping them together would be enough to make sure there's no man left behind 😉

[@paulkivisto9060]

Don't there are valve cap?

[@ElectricUnicycles]

No valve cap is supplied, but you could always put one on if you want to.

[@Electric_scooter_ride]

My friend. Hey) What's the matter?

[@moparbro]

Whoa

[@cheapspace]

the z10 extender is a stupid design you really do have to push hard to screw it on because the end is a hand screw type not a fixed type. The fixed type will go on as you screw from any point of the extender what a dumb decision on ninebots part.

[@TheOriginalAndysGarage]

Anybody else getting me a strange high-pitch feedback from this guy's camera

[@hatemaliforobjection2414]

How complicated in ninebot like always . Please go see how cool to full air in inmotion . I remember in my x ninebot E+ HOW I was suffering to full air . Sucks ninebot as fuck. Honestly inmotion much better by 10000 times no compare