Nissan # 1.2 # H5FT # Engine # Timing chain rattle # Replacement chain

Created by InShot
inshotapp.page...

[@mustafaiqbal9204]

Brilliant video dude, hats off to you for tackiling it 👏

[@cardiagnosis8199]

Thank you for the feedback

[@mahmutkocakcom5962]

👏👏

[@tariqzaman7409]

Thank you for posting such a great video, I have the same issue with my 2015 Pulsar. It’s only done 59,000 Miles, the oil pressure warning light is coming on intermittently but the rattling has been present for over 6 months. A local garage mechanic found nothing wrong. Do you have any idea what sort of price this job should cost pls?

[@user-iw6bn2vm3o]

Похоже на стук цепи ГРМ.

[@Apuokenas]

Do you, by any chance, remember the mileage on the odometer? It's sad that according to the manual, the chain needed to be replaced only after 300,000 km; however, in reality, the actual number is much lower (~3.75 times), no matter that the oil has always been replaced every 6,000 miles or so. 😢

[@cardiagnosis8199]

Hi This engine had covered 67506 km .

[@beatonthedonis]

@@cardiagnosis8199 Exactly the time I got my timing chain rattle in a 1.2 Pulsar. Nissan changed it for free out of warranty, because I'd always serviced it at the main dealer.

[@ssss-df5qz]

This is what happens when you buy cars with crappy French engines in them. I'm surprised your DIG-T didn't blow up from excessive oil consumption before the chain went.

[@cardiagnosis8199]

Hi . Sorry I didn’t count so I’m not sure . But it take a lot of turns . May up to 20 turn overs. Hope this helps .

[@hayche1986]

very informative video thank you, would that tooth being out cause a popping sound on deceleration and possibly a 3000rpm vibration by any chance?

[@igp3130]

Hello mate, did you have to lock the camshafts with a kit or just keep some spanners on them?

[@NSEMRAIR]

How many times did you had to turn it to get back to match on timing marks do you remember ???

[@danisimo1385]

Проблему не решили, зато поменяли цепь. Проблема в форсунках-омывателях, где перестает работать клапан и масло стекает/вытекает из блока - нет давления и башмак не натягивает цепь. Сейчас найду видео - кину ссылку.

[@danisimo1385]

Надеюсь это кому-то поможет

[@redfish0]

How did you get the crank pulley off?

[@r33gts2009]

Hi thanks for the video ,was it necessary to remove the rocker cover ?

[@liaquatali-mm2dy]

I have the same issue on my juke

[@kuidokanarik7455]

Hi, do you remember sizes of these o-rings in camshaft covers? Cant find anywhere and only whole cover is for sale.

[@henrietabacova8285]

Hi buddy, the water pump started leaking on my Ulysse 2.0 petrol, just wonder if it's a big job to replace the whole part including housing??

[@Myto321]

hello, very helpful vid thanks, what diagnostic tool are you using?

[@cardiagnosis8199]

Hi It’s a Launch Pro 5 plus

[@liaquatali-mm2dy]

What was the cost ?

[@rs_99_]

Hi.. roughly speaking what could i expect a garage to charge to do this...dealer & indy

[@spanthefestaman]

How come you had to take the cam cover off??

[@kaikaineilps5]

How did you lock the timing if u can tell me please

[@TheMattyholt]

Could this be done without removing rocker cover or not enough room to get chain out? Cheers

[@cardiagnosis8199]

I don’t believe so as the bolts for the rocker cover go into the timing chain case . I would advise to always follow the repair instructions to eliminate any mistakes . Hope this helps

[@chrismills9346]

Yeh it can I done one today with out taking rocker cover off 👍

[@paultownsend3698]

Do you need locking tools

[@dimvasileiou974]

Hi how about oil consumption ; I have the same engine 60k km and mine consumes 250ml per 1000km

[@cardiagnosis8199]

Hi Unfortunately I’m not sure of the oil usage specs on this engine . I was doing a timing chain replacement . Owner of the car didn’t mention any oil usage .

[@user-iw6bn2vm3o]

Пробег 89000 расхода масла нет.

[@mohamadamen8079]

Hi, can you tell me how to find the adjustment tool for this motor?

[@cardiagnosis8199]

Hi There is not adjustment tool required . The timing marks are on the chain which you line up with the correct marks on the cam pulleys and crankshaft pulley .

[@robertoviscardi4326]

Numero km? Tank you... 🇮🇪... Ciao

[@cardiagnosis8199]

Hi 67506 Km the engine had covered .

[@robertoviscardi4326]

@@cardiagnosis8199 My car Qasqai DIG_T 1200, 7 yer, km 90000...goud! Ok... Ciao🇮🇹

[@user-iw6bn2vm3o]

​@@robertoviscardi4326 Такой же Кашкай. 6 лет 89000 км

[@igp3130]

Hello mate, did you have to lock the camshafts with a kit or just keep some spanners on them?

[@cardiagnosis8199]

Hi No didn’t need to lock the camshafts.

[@igp3130]

@Car Diagnosis cheers man, do they try to spin at all or did you just keep some spanners on them? Gotta do one tomorrow and it's not a engine I know that's all

[@cardiagnosis8199]

@@igp3130 cams stayed in the position.

[@dantolhurst7802]

​@Car Diagnosis do the cams move out off time wen tension is released off chain...

[@Kangoo172]

Great video, thank you. Did you need to remove the alternator and a/c pump? Just about to do one on a Juke and the repair manual says to remove them both.