No Tools, No Problem! Back Brake Swap.

  Рет қаралды 34,615

DD Speed Shop

DD Speed Shop

Күн бұрын

Пікірлер: 223
@SBGHTEACH
@SBGHTEACH 23 күн бұрын
Danielle is amazing in how she just knows where everything is, you are a lucky man!
@RandyH-qf3dc
@RandyH-qf3dc 24 күн бұрын
The car is coming along. When working on drum brakes, I always take off both tires and drums, then work on one side at a time using the other side as a reference. Works good as long as the guy before me didn't mess up the last brake job. Lol. Can't wait for the test drive
@JamesDuncil-nb7vt
@JamesDuncil-nb7vt 23 күн бұрын
Much as I loved watching you struggle on the floor of your freezing cold shops in Manitoba, I'm glad u have a actual lift and a shop where you can wear short sleeves in the winter. Keep doing what you do. I really enjoy watching you guys.
@Tonymarony5113
@Tonymarony5113 23 күн бұрын
Definitely. Why struggle if you don't have to?
@LynnMacKenzie-w2s
@LynnMacKenzie-w2s 24 күн бұрын
It does really help to have the tool to turn the little caps on those small springs.
@ELNomad55
@ELNomad55 24 күн бұрын
When not available I used needle-nosed pliers to install those spring caps.
@AJsHotRodsNrepairs
@AJsHotRodsNrepairs 24 күн бұрын
princess auto sells a nice pair of old school brake spring pliers.... just sayen
@donaldhalls2189
@donaldhalls2189 23 күн бұрын
​@@AJsHotRodsNrepairsthey certainly do make it easier, with the Springs and those caps, I struggle a bit with just pliers and screwdriver, handy to know those pliers are still around, all the best to you all
@kimberlywilliams9757
@kimberlywilliams9757 24 күн бұрын
Like Mortske says, it doesn't matter how you get it done as long as you're having fun! 😊
@peter-pg5yc
@peter-pg5yc 22 күн бұрын
not on old mb cars, they are annoying
@renchjeep
@renchjeep 23 күн бұрын
Dude, the adjuster would work a whole lot better if you used the correct spring on the bottom! LOL. And the self-adjuster is never gonna work with that spring rubbing on the star wheel. Anyway....You definitely need more drum brake practice, my friend. It was fun to watch, but then again SO frustrating as I yelled at the screen all the advice I had to give! Haha! Take care, Dan and Dani.
@hardball107
@hardball107 24 күн бұрын
Dan, Dude, Just attach the shoes onto the backing plate and add all the other parts by just moving the shoes around on the nails. Lots of play there, pop the springs on and you're done. 5 minute job per corner. It was painful watching you try to balance everything but I have to thank you for the chuckle. Love you to Dannie.
@axemanfishing2703
@axemanfishing2703 21 күн бұрын
Man, the car is really coming along nicely.
@CrazyWillie01
@CrazyWillie01 23 күн бұрын
Dang Sunday, and no DD Speed Shop and Dan & Dani Dang it lol need my fix got 2 different surgeries next week Tuesday and Thursday and won’t be able to work on my Chevy for 8 weeks
@Darkflamingo
@Darkflamingo 23 күн бұрын
Slide a box end wrench over the E Brake cable end to push all the tabs in at once, easy peasy.
@peter-pg5yc
@peter-pg5yc 22 күн бұрын
Again needle nose vise grips push housing back then clamp super easy. some cars are stupid strong springs
@Darkflamingo
@Darkflamingo 22 күн бұрын
@@peter-pg5yc Not at all what I'm talking about, Pete.You're talking about the spring end that connects to the parking brake lever inside the brake drum. I'm talking about pushing all the fingers in on the circular brake cable clamp where it snaps into the backing plate. That's where Dan was struggling with it. He destroyed the old cable end taking it out, which is fine, but if he ever wants to remove a good parking brake cable without damaging it to reuse on another rear end, my way will allow that to happen.
@charlesdirienzo6422
@charlesdirienzo6422 17 күн бұрын
FYI I bought a set of HVAC tubing springs that were designed to help bend copper line. You put the correct size spring over the tubing and it bends it without kinking. Works great on nickel copper line
@narrowgaugegreg
@narrowgaugegreg 24 күн бұрын
I like the little "Rocky Horror Picture Show" reference.
@geraldscott4302
@geraldscott4302 23 күн бұрын
Dammit Janet
@Pittsburgh57Chevyguy
@Pittsburgh57Chevyguy 23 күн бұрын
Dani always knows best!!
@stacysanders-w3e
@stacysanders-w3e 24 күн бұрын
When you bench bleed a dual master cylinder those plastic hoses return the fluid to the reservoir when you press the piston in. But if they are submerged in the fluid they also draw the fluid back into the cylinder when you release it. They have to be submerged to work the air out.
@stevebriggs884
@stevebriggs884 24 күн бұрын
This was the most painful video to watch! I've done these brakes 1000 times, when I worked at Speedy and Midas. Oh my Gawd!
@KenBuckley
@KenBuckley 24 күн бұрын
Worked for Midas for many years and this was a daily thing to do 5 minutes a side easy peazy
@dogsense3773
@dogsense3773 24 күн бұрын
B.s
@stevebriggs884
@stevebriggs884 24 күн бұрын
@@dogsense3773 What's B.S. Buddy? Do I need to show you my Licence, and when it was issued?
@wrenched90405
@wrenched90405 23 күн бұрын
super painful, I think I’m getting dumber watching this ~ and I’m not even Canadian!
@paulkelly1809
@paulkelly1809 23 күн бұрын
Something is wrong with your camera. It has blurry spots on the screen that move around
@AnthonyjGoldajr
@AnthonyjGoldajr 24 күн бұрын
Keep up the great work yas both 👍👍👍
@donaldhalls2189
@donaldhalls2189 23 күн бұрын
Getting it done, great job, thanks for sharing, all the best to yous and your loved ones
@connor454bigblock
@connor454bigblock 23 күн бұрын
That rear end and master cylinder is out of a chevy s10 early 90s if it makes it easier to order parts for you guys i tell by looking cuz camaro one would have a Mounting spot for a troque arm
@franklindner8259
@franklindner8259 22 күн бұрын
Your videos on larger repairs such as sheet metal repair are better because of larger size but zoom lens would improve them. Love the content and u guys.
@glenharper3136
@glenharper3136 23 күн бұрын
Thanks for the video you 2.
@jimbrown3720
@jimbrown3720 24 күн бұрын
New bigger shop new lift and it looks more cluttered than the last place i cant believe you dont get hurt more often .
@Jdwescott
@Jdwescott 24 күн бұрын
Waiting for the where's the chevelle,is the chevelle at the old place,when are you getting back on the chevelle,do you still have the chevelle comments.
@TheInternetSaidThis
@TheInternetSaidThis 23 күн бұрын
Think I asked about it once after they let the world know they moved and wont ask about it again as they have responded about it by my count 3 times since. I am more of a A-Body, 68-72 guy than a tri-5 guy but he takes on projects I would never mess with and brings them back to life and ill watch every one of them they share with us. Being completely objective, that Chevelle would be about 4th in line to consider bringing to the new place over some of his other cool cars.
@charlesdirienzo6422
@charlesdirienzo6422 17 күн бұрын
Great news I heard Canada with be 51st state in the US. Parts will now be cheaper and easier to get!! You’re welcome
@tcjatko7964
@tcjatko7964 23 күн бұрын
Good God, man. Invest in a brake spring plier! All the tools you need in one package. Imagine that.
@Zazu2You
@Zazu2You 24 күн бұрын
Those drum brakes and brake lines are fun. Nice work, Dan. Cheers!! 😎
@cobyburrow9339
@cobyburrow9339 24 күн бұрын
Alternative Spring installation tool, largest Phillips head screwdriver you have in the box. Works great when you don't have a brake tool.
@johnchambers12
@johnchambers12 24 күн бұрын
I still have all of my drum brake tools and I’m not afraid to use them. Good video as always. The right tool would be the one that gets the job done without braking a window with a spring. And making brake line , when i was a young lad , the best double flare i made was on the line Before i put the fitting on. Just saying,it can happen!
@terrycole9427
@terrycole9427 22 күн бұрын
Brakes are always fun
@SBGHTEACH
@SBGHTEACH 23 күн бұрын
that parking brake lever on my Mustang (same sort of mess), I had to bend the living daylights out of it to get it to fit and actually work
@ImthePaulshouldnotbeallowedtod
@ImthePaulshouldnotbeallowedtod 23 күн бұрын
You should ask for another hydraulic lift for the other bay of the garage. You can justify asking for a second unit, because of the at least 80 percent screen time that the lift is getting on your channel and put large stickers with the company's name ,all over the lift. Just a little thought that I was thinking, ever since you have been using it
@johnkranz4004
@johnkranz4004 24 күн бұрын
Good job Dan Dani coming along
@billtopka2584
@billtopka2584 24 күн бұрын
Coming along nicely! 👍
24 күн бұрын
Great brake job!
@georgeleech2709
@georgeleech2709 23 күн бұрын
Dan , there is usually only three of the tabs on the emergency brake cable that go through the backing plate that are spread out
@derek2380
@derek2380 23 күн бұрын
Telling him to check his pictures was the highlight of the whole video 🤣
@Johnsmusic416
@Johnsmusic416 23 күн бұрын
Looking Good!! Going to be a nice Cruising Machine!!
@benshore7357
@benshore7357 24 күн бұрын
Looking good 🎉 taking a picture is a good idea as long as the guy before did it right 🎉
@bobhalstead1879
@bobhalstead1879 23 күн бұрын
Hey dano try using a hose clamp on cable end to compress tangs.so simple and effective.
@redwinstead7873
@redwinstead7873 23 күн бұрын
It looks like Danny is getting more stuff done when she is working on the car 😂😂😂❤❤❤
@mattthescrapwhisperer
@mattthescrapwhisperer 22 күн бұрын
I have a permanent mark on my forehead from all the drum brake spring retainers that have slipped from the pliers and launched with full spring tension straight at my head. I bet Mur has the same mark.
@ELNomad55
@ELNomad55 24 күн бұрын
On my 55 pbrake adjuster I drilled a clearance hole for the threaded part and put nuts on each side of the adjuster rod. So much easier to adjust.
@glennshotrodgarage5509
@glennshotrodgarage5509 23 күн бұрын
Put a fuel line hose clamp on the emergency brake cable and tighten it push it trough the backing plate until the fingers are through the backing plate!
@waynebernier1061
@waynebernier1061 22 күн бұрын
You had lots of tools back in Winnipeg, curious why you didn’t bring them with you?
@HankWeidman
@HankWeidman 22 күн бұрын
Nice Drums😊
@kennyschulz5963
@kennyschulz5963 23 күн бұрын
You can use a small hose clamp to release the e-brake cable
@JimmyMakingitwork
@JimmyMakingitwork 24 күн бұрын
This is why the guys at the shop always hand me the drum brake jobs, haha. With most GM's attach the adjuster, lever and lower spring, primary shoe(smaller) in front, hang it on the pins, then the upper springs last making sure the wheel cylinder pins made it into the shoes. Sounds easy doesn't it, haha. Oh and make sure the adjusters are on the correct side if they are "auto adjust" brakes with the cable and lever from later models.
@spicedude6230
@spicedude6230 24 күн бұрын
Tell Dan not to forget to tighten DEEEZ Nutz on the top of the Lift
@EdwardVanmoppes-kv4tv
@EdwardVanmoppes-kv4tv 23 күн бұрын
My first rear drum break job I did ba k in 1992 was a disaster. Figured it out since, however after the 30 or 40 successful times I still dread them.😮
@OldMan53-q4t
@OldMan53-q4t 24 күн бұрын
Hey Dan you should be able to adjust your pinion angle by using wedge shaped shims between the spring purchases and the springs , like they use to adjust the caster on a straight axle front end . Just like on Dani’s Chevy II .
@davidhammons800
@davidhammons800 24 күн бұрын
Can't wait to put on my headphones & listen to you do some rips. Keep kickin' ass you guys!
@mamma7119
@mamma7119 23 күн бұрын
I'm 58 years old I have always done All my brake jobs myself I bought one of the brake tools once I ended up throwing it out through the yard I went to my tool box and grabbed my vice grips and needle head pliers and flat head screw driver and had that job and a lot of others done
@VintageTinGarage
@VintageTinGarage 23 күн бұрын
Dan you have the focus and attention span of a Gerbil 🤣. All kidding aside the 55 is coming along nicely.
@henryallisonsr8318
@henryallisonsr8318 24 күн бұрын
I hope you clean and undercoat the under neath the Chevy and fix the holes and dents and give it a good paint job. God bless and have a blessed night
@br549200
@br549200 24 күн бұрын
Greetings from northwest Missouri. Our first inch of snow this morning to shut down Kansas City😂
@donaldkidder4766
@donaldkidder4766 23 күн бұрын
That really is a good looking hot rod even for a four-door!
@edwinbonnelljr1587
@edwinbonnelljr1587 24 күн бұрын
Nice looking car man ❤❤❤❤❤
@marcstruglia5910
@marcstruglia5910 24 күн бұрын
Greetings from central (Mid) Missouri. Our first inch of snow this morning just shut down Columbia!
@xozindustries7451
@xozindustries7451 24 күн бұрын
You can get sone wedges to put between the rear end and leaf springs to correct the pinion angle, it should help the clearance on the parking brake mechanism
@Tonymarony5113
@Tonymarony5113 23 күн бұрын
I really like this car. I like the colour combination but also a four-door and a cheap 305 is appealing to me. Yes, two doors and big hp are cooler, but this is a practical daily driver. This is in reach of the average man.
@deerespetes8849
@deerespetes8849 23 күн бұрын
So the fender well headers are creating difficulties with your brake lines talk to the hand 🤔
@stephenferriss-x5j
@stephenferriss-x5j 23 күн бұрын
come to the USA , MORE CAR SHOWS AND SWAP MEETS.
@peter-pg5yc
@peter-pg5yc 22 күн бұрын
Needle nose vise grips smaller ones perfect and set up 1st one 2nd is fast. for those twist washers. The old screwdriver trick for the springs.. Plus largr needle nose vise grips work great on springs. i hate extra tools that laugh at me in tool box.. so i improvise.
@timross7584
@timross7584 24 күн бұрын
I use that brake line all the time easy to bend use it for fuel line also love that stuff
@Barret_Radtke
@Barret_Radtke 23 күн бұрын
i did the the brakes on a 65 meteor and those push pins are so frustrating. drums all around all 4 wheels. i had had to borrow my dads brake tools as trying to use pliers makes it a million times harder and yeah i tried to do it the same way. I filmed it for KZbin as well.
@robertc1433
@robertc1433 24 күн бұрын
looking good guys
@CrazyWillie01
@CrazyWillie01 24 күн бұрын
Winter came to Washington state open carport shop surgery on Tuesday and Thursday on my neck front and back, so I’ll be down till February lol love the channel and you guys . Happy Holidays , ( say it now as not sure I’ll be on threw December due to my neck recovering but I’ll try , gotta have my DD Speed Shop fix
@johnkolodziej1692
@johnkolodziej1692 24 күн бұрын
It looks like it is warm enough in the new place. Dani is doing a fine job as camera person! Drum brakes is all there was when I was young. You kinda had a hard time with your drum brakes! Must be because you are use to disc brakes.
@TheMasterofsparks
@TheMasterofsparks 23 күн бұрын
OMG! Dan doesn’t know how to replace drum brakes, maybe he really is a hair model 😂
@jonahguitarguy
@jonahguitarguy 23 күн бұрын
Last few times I've watched I keep yelling at the screen, move the tool cart to where you're working. And then get yourself another one to throw all the trash on. You got a lift and you're still making it hard on yourself. And there are a few of you car guys I watch and am amazed that you don't have a pressure bleeder for brakes.
@homer714
@homer714 24 күн бұрын
Resetting the pinion angle might help with the e brake clearance on the driveshaft
@Tim-57
@Tim-57 24 күн бұрын
Hey Dan&Dannie Happy Weekend Take care😊
@travistuttle9274
@travistuttle9274 24 күн бұрын
7/16" wrench usually slides over those e- brake cables just fine!
@JakeWeddle-zo4xv
@JakeWeddle-zo4xv 24 күн бұрын
I ripped all the brakes off my 51 then remembered i was gonna take pictures... good times 😕
@aprilhilliard3302
@aprilhilliard3302 24 күн бұрын
Back in the mid '70s, we didn't have the ability to take pictures like that. I had a notebook and drew little diagrams, because I had no one to help or show me. Can't complain...it worked!
@615theBuzzard
@615theBuzzard 23 күн бұрын
Almost ready to do a burnout
@TheSaxon25
@TheSaxon25 23 күн бұрын
Rocky Horror shout out 👌👌
@johnroof2663
@johnroof2663 24 күн бұрын
Man, it's all good. Sometimes, you just have a bad day. Nothing's but thing. I hate working on drum breaks myself. They're a pain in the ass.
@TairnKA
@TairnKA 23 күн бұрын
It's timing; you remarked about welding near a gas tank and at the first tack an ad starts with a black screen. ;-D
@marksanders1942
@marksanders1942 24 күн бұрын
That brake line is not only ok, it’s really good. Easy to bend and hard to rust. It’s not copper. Only copper coated
@upscaleshack
@upscaleshack 23 күн бұрын
It's not copper coated, it's an alloy of copper, nickel, and iron. Cu, Ni, and Fe. That's why it's called cunifer. It's been standard equipment in Europe for decades.
@leonardowelch2580
@leonardowelch2580 24 күн бұрын
Come on Miss Danyel Laughing at Mr Dan when he hits his head. I thought you loved him? Hopefully y'all play that way. May God bless you and t
@timmygiles9554
@timmygiles9554 24 күн бұрын
Dikes and a straight head screw driver and I normally get lucky,just glad to see you with a lift. Now quit f-ing around we should be riding already!!!Hey Dani
@kimberlywilliams9757
@kimberlywilliams9757 24 күн бұрын
😳
@NH1969GOAT
@NH1969GOAT 24 күн бұрын
Back in the 60's we used lubriplate for adjusters and friction points.
@BigBlock-wf3mh
@BigBlock-wf3mh 24 күн бұрын
You would think Kroil would make an Air Freshener for the car. 😎
@roberttaynor5672
@roberttaynor5672 24 күн бұрын
hay did you put the short cable in there
@PaulPreston-qw1yg
@PaulPreston-qw1yg 24 күн бұрын
Danny never give up never surrender.you can do it
@suecobandito8954
@suecobandito8954 24 күн бұрын
Convert it to two doors. Looking good.
@LynnMacKenzie-w2s
@LynnMacKenzie-w2s 24 күн бұрын
No way; this is a super suvivor
@Speedy2222
@Speedy2222 23 күн бұрын
Do you have plans to restock the stock with Certified Garage Hack shirts? And i'm not just talking about the ones Dan hangs in his closet.
@vincentenk4449
@vincentenk4449 23 күн бұрын
On removing the E Brake cables from the backing plate, slip a box end wrench over the cable & smack it over the mount deal & it'll slip right out.
@joehoeksema2686
@joehoeksema2686 24 күн бұрын
E brake cable removal tool is the same as boxed end of combination wrench here in the USA anyway
@brettemerich3237
@brettemerich3237 24 күн бұрын
Dan on the road soon. Yes attach the ground to the body close to where you are welding And not to the gas tank flange. Dan and Dani Nice entertainment
@1944chevytruck
@1944chevytruck 23 күн бұрын
GOOD JOB!
@joefergerson5243
@joefergerson5243 23 күн бұрын
Pretty nails Danielle❤
@markmckeachnie4484
@markmckeachnie4484 24 күн бұрын
That kroil smells so good you can use it as a bathroom deodorant,but I don’t think Danny would like that!
@gregorygibson5455
@gregorygibson5455 24 күн бұрын
Hello Dan n Dani
@henryallisonsr8318
@henryallisonsr8318 24 күн бұрын
Just want to say hi to you all and hope you had a blessed Thanksgiving. God bless and have a blessed night
@timmiller260
@timmiller260 24 күн бұрын
Now the drakes needs fix rust holes in rockers this is n I ce car😊.
@Musclecarcustomgarage
@Musclecarcustomgarage 23 күн бұрын
Don't need modern tools for an old setup. 😂 Lol , vise grips , duck tap and zip ties. Good to go
@steelmill
@steelmill 24 күн бұрын
The tool cart would come in handy under the car.
@4dszr164
@4dszr164 23 күн бұрын
Haha. Love the beginning
@rongladden809
@rongladden809 24 күн бұрын
Keep up all the good work ms Dani ,you might get to drive it before Xmas or at least sit in it to take Xmas pictures. Dan you do a fine job
@VATION3RD-GEN-X-GARAGE
@VATION3RD-GEN-X-GARAGE 23 күн бұрын
I like it, Now that y'all have the lift Ms Danni can actually get close up and film like Jolene does, and we can see what Dan's doing...
How to Replace Rear Drum Brakes Toyota Tacoma 2005-2023
13:48
Team Oil Drop
Рет қаралды 78 М.
13 Year Old Buys a Truck! Rats Ate the Wiring!
1:27:58
Sleeperdude
Рет қаралды 249 М.
«Жат бауыр» телехикаясы І 30 - бөлім | Соңғы бөлім
52:59
Qazaqstan TV / Қазақстан Ұлттық Арнасы
Рет қаралды 340 М.
Jaidarman TOP / Жоғары лига-2023 / Жекпе-жек 1-ТУР / 1-топ
1:30:54
Classic Car Vs. Winter What Could Go Wrong?
37:59
DD Speed Shop
Рет қаралды 13 М.
Brake Failure? Don't Be That Guy!
56:46
DD Speed Shop
Рет қаралды 36 М.
SIEZED Honda - Will it RUN & RIDE after 30 YEARS!?
47:37
Junkyard Digs
Рет қаралды 383 М.
Customer Says - Give Me A Brake!
38:10
South Main Auto LLC
Рет қаралды 158 М.
New Problems Present Themselves Gearing Up For The First Drive!
44:06
What Will It Take To Buy The RAREST Motorcycle I've Ever Found?
24:06
Wheels Through Time
Рет қаралды 353 М.
Saving two BULLDOZERS From becoming SCRAP! (Caterpillar D8H & HD11)
55:38