Nice project. Thanks for posting. Note that the crimpers have two indications. Rear one for insulated connectors and the one forward for Non insulated. Use the rear INS for connectors that are insulated like the ones used here. The forward “notch” is for bare connectors.
@johnlshilling14463 жыл бұрын
Very well done and explained very well, even for beginners. I only have one objection... decades ago, electrical tape was disallowed for capping and splicing wires, according to National Electric Code. I know that it worked for apprx 100 years before it was banned, but enough electrical fires were caused due to poor taping, that the Code was changed. Wire Nuts and splices should be used wherever possible. Especially when dealing with voltage above 24v. 😁 It's just safer, especially for beginners.
@WJCTechyman2 ай бұрын
I agree. I would just cap the ends with small Marrettes (I'm Canadian and a Scottish-born Canadian named William Marr invented the wire nut while working for Ontario Hydro so that's what we call them) and then, if necessary, taping them.
@robr4713 жыл бұрын
Great idea, I did a version of this almost 20yrs ago, because I had a basement apartment and the windows were too small to accommodate a window air conditioner. It essentially sat outside my window under a small clear awning with the duct pushing air into the room. The power cable was on a surge protector and the controls were set to "high". I'd just flip the switch to the surge protector to turn it on when I wanted things cool. Very primitive, but it made a difference, especially when alternatives were not really an option for me. Now portable ac units are more affordable and available.
@rummy987 ай бұрын
Window units take inside air, cool it and blow it back into the room. A closed system. The condenser is located outside and water removed from the air is also dumped outside. Portable units don't work as well because they exhaust indoor air to the outside. If you remove air from a room, you must replace it with new outside air (negative pressure that pulls in outside air in any crack it can find), reducing the efficiency by a lot and also bringing in additional humidity. Since the condenser is on the inside, the heat and water produced are also on the inside.
@whydontyouaskme5 ай бұрын
@@rummy98bro there has dual hoses for years now. You sound like you’ve been living under a rock.
@trikator3 ай бұрын
@@whydontyouaskmebut most of them are single hose units
@WJCTechyman2 ай бұрын
@@trikator That is true, most of them are single hose units but I saw on Canadian Tire's website (so it's probably available in the States too) Midea has a few models with dual hose design. It's a form of hose inside a hose unit that appears as one large oblong hose from the outside.
@c50ge3 жыл бұрын
I was repairing a microwave 40 years ago and got hit with a capacitor charge. Trust me it’s a feeling you will never forget. Makes 120 volts just a tickle. Me arm was sore for a week!
@dopeymark3 жыл бұрын
That happened to me with a CRT television when I was about 14. Mistakes I will never make again.
@mikecorleone67973 жыл бұрын
I remember the first time i got hit with the magneto on my plane.. holy crap, i flew with a twitch that day
@bradfader6913 жыл бұрын
Ha been there! I was working on a machine that tests solar panels and it held 70v dc and unbenounced to me it wasnt discharged. Ouch lol
@rebus5703 жыл бұрын
We used to charge them up & toss them to the helper & say "here catch", they learn real fast not too.
@bradfader6913 жыл бұрын
@@rebus570 hot potato lmao
@wideawaketotruth53013 жыл бұрын
Very well done, I'm impressed with the level of detail that you indicated in your video. Again well done my brother well done!
@abcdefgmynameisbsabc3 жыл бұрын
Looks like a fun project! I will say, though, that when you used the grinder I got a little nervous. Typically you want to run it so the sparks are shooting towards you, so that when (not if) the grinder catches and binds, it pulls itself away from your body, and not towards it. Stay safe out there!
@johnlshilling14463 жыл бұрын
Have to agree... because I've suffered the consequences. 30 years experience, and "I knew" I had it under control.. LOL! Emergency Room and 20+ stiches. VERY lucky I didn't cut tendons... "..Just a flesh wound.." to quote The Black Knight in Monty Python's "Holy Grail"
@patrickday42065 ай бұрын
@@johnlshilling1446tis but
@lifestooshort81 Жыл бұрын
I've had this idea for many years except mine included a plug-in box. I love how you incorporated the relay & transformer inside the unit for a clean look. Fast forward a few years and I now have my own place I plan to do this with until I can afford to install a mini-split system. Thanks for sharing! ;)
@CDP135Z Жыл бұрын
This may be the best way to explain how an air conditioner works. Or at least to get an understanding of the basic components of an AC. I was looking at doing something similar, but just sorta backwards. Putting the unit inside my garage and ducting the intake and exhaust outside.
@acrepairnearme3 жыл бұрын
To determine the speed on the AC blower motor you can measure Resistance btw neutral and each wire. The lowest resistance mean higher speed. Higher resistance mean lower speed. Etc.
@brianluck843 жыл бұрын
He also could have used that same multimeter to just see what wire had voltage based off speed setting.
@WJCTechyman2 ай бұрын
@@brianluck84 Or an even safer method of testing, using the continuity setting on the multimeter while turning the knob and listening for a buzz. You don't have to plug it in at all. The continuity setting on my multimeter looks like a sideways Wifi symbol.
@goiterlanternbase Жыл бұрын
18:58 When you don't want to glue two parts together, but still have a seal, apply tape on one side. It also works with caulking. After the sealant is cured, the tape even can be removed, if more pressure can be applied to the seam, like with tightening a screw or such measure. Which type of tape you ask. It depends on the job. Some tapes stick a little more to the sealant, others are thin as a hair. Painters tape, is the easiest to remove. Sometimes cling film is enough🤗
@jeeper4263 жыл бұрын
i was considering building something similar for a tent aircon, but i'm going to be getting a camper shell for my pickup, so i might use a sheet of old plywood, make a blockoff and cut a hole for a window unit, still not a bad setup, and this reminds me of a project i had to do for Tech to get my HVAC certs, good times, stay safe out there
@dallynsr3 жыл бұрын
Very respectable video and well explained. Being this is 2021 headed to 2022 fast, mini houses need 20seer heat pumps for excellent and aesthetic cooling/heat. I install 3/4 ton(9000btu) units for not very much and there’s no need for the re-engineering and sharp sheet metal work and bloody knuckles for minimal gains.
@ericcoombs3 жыл бұрын
So cool that people can learn this type of thing on KZbin! 👍
@shplayshiggty75373 жыл бұрын
I dig it however 2 things I noticed. #1 an insulated boot will be better just for the fact of condensation. It'll probably help reduce the amount of heat dissapation, this is why the foam is inside the unit in the first place. This leads into #2 the foam will make a difference as well, some foams such as great stuff will hold up for awhile but it will definitely degrade quick. Find some closed cell expandable foam, that will insure it lasts as long as the unit as it holds up to water erosion. Otherwise a great idea for a hunting shack or a tiny home.
@arihirschman68843 жыл бұрын
Nice project. Thanks. One bit of "Free" advice - I used to manage 16 apartments that had lots of window units. The cheap 5000 BTU units never seemed to last, so I moved up to better quality 6000 (Much more selection at the 6000 range) units. $50 bucks got me at least 2 or 3 times the lifespan.
@TinyGiantLifeStyle3 жыл бұрын
That's good to know. For a few bucks its a throw away for sure. I would never pay the summer time price for them
@WJCTechyman2 ай бұрын
Or, you ask the property owner to invest in PTHP units like those seen in hotels. Yes, it requires a 240 V circuit to the area you install and yes, it requires modifying each apartment with a hole in the wall in which a steel sleeve is installed but the PTHP is at least built to last as long as a whole house (central) air conditioner and if there are problems, you simply pull the face plate and swap out the unit for another one especially if it's just plugged into a 20 A 240V outlet.
@totallyunmemorable2 жыл бұрын
Exactly the problem I've been looking to solve. Tiny space, too loud, too cold AC. They used to make air conditioners that were much smaller, apparently they no longer do. I sense a springtime project in my future.
@TinyGiantLifeStyle2 жыл бұрын
Exactly
@DavidDJenkins4 ай бұрын
When doing this. Does the return need to be connected to the inside of the room you are cooling? Or can it just pull in air from where it's sitting?
@totallyunmemorable4 ай бұрын
@@DavidDJenkins The way air conditioners work is the bottom part with all the aluminum fins is where the hot room air enters, and then the cold air is blown out the top vents. So you wouldn't have much luck drawing air from outside your room. It'd probably work, just not very well.
@WJCTechyman2 ай бұрын
My 5000 BTU unit is probably about 20 inches wide (50 cm), maybe a bit over a foot tall (over 30.4 cm) and maybe deeper than its width and weighs maybe 20 to 40 pounds (mass of 10-20 kg). It's pretty small especially compared to my portable AC.
@annespacedroid3 жыл бұрын
Put a sonoff relay set in there and be done with it. Controlled remotely, no wires running into the house. Because of the resistance (airflow) through the tube, I'd check the heat of the fan motor after it has been running for a couple of hours.
@MichaelSchmitz-mk8ll3 жыл бұрын
Perfect for a grow room thank you for showing...
@lawrencelile3 жыл бұрын
Awesome! I'm faced with a similar project fitting an AC into a teardrop trailer. This gives me some ideas!
@allthingssilver76353 жыл бұрын
I'm building a teardrop camper. Got my trailer stripped down to just the frame. About to add the floor. I'm at beginning stages. I was watching this and thinking I should incorporate this into my build somehow.
@NoBs483 жыл бұрын
Are you going to make a video ?
@allthingssilver76353 жыл бұрын
@@NoBs48 I would make a video but know nothing about editing and my phone don't take quality videos. Id have to buy a cheap camera and don't know what kind of camera to get thats not expensive but is good enough
@WJCTechyman2 ай бұрын
Interesting setup. I would have made the intake a bit different where crafting the front panel would be a custom sheet steel design (same kind of galvanized sheet steel used in HVAC) to fit over the entirety of the evaporator coil and then using a duct boot like you have there to transition to the return. Using tools like pop rivets and metal snips makes the work look more professional and the supply vent maybe insulated with exterior barrier-style foam sheeting and securing into place and reducing leaks with the handyman's secret weapon: foil duct tape.
@TheSkinnzer3 жыл бұрын
Use wire nuts when making a stop termination. Or better insulation then electrical tape. It might bet rated for 600 Amps, but can it stand the outdoor condition of the rugged outdoors?
@Garymayo3 жыл бұрын
This may pose an advantage over a window unit in a window, but in the massive effort to retrofit a window unit this way, just purchase a small Mr Cool mini split. It will work massively more efficiently and heat as well as cool
@mitchmaule65173 жыл бұрын
Yeah for a grand bro
@flanny7013 жыл бұрын
the whole point of this video was so that we avoid paying more than ~$200 for a mini split and it wouldnt be massively more efficient just slightly more depending on how well the cool side is insulated from the heat of the outdoors
@davej6523 жыл бұрын
There are a lot of bad reviews for Mr. Cool failing after only a few years. Not to mention the cost of an HVAC tech to diagnose any problems. You can get window units dirt cheap used.
@WJCTechyman2 ай бұрын
@@davej652 If I was building a tiny home, I would find a place to just mount it in a wall. Heck, I would even pay the price for a wall mount heat pump as that will give the simplicity and advantage of a window mount but designed to go out an exterior wall and also some of a heating advantage as the coefficient of performance would be higher than regular resistive electric heat. That being said, one may have to determine their best solution and electric baseboard or forced air heat may be something that can be used in the event that the heat pump can't.
@DeAthWaGer3 жыл бұрын
Awesome! I'd use a bit of silicone caulk around all the electrical stuff, just as a precaution. Is also great to finish off seals wear the foam might flake off.
@barnowl68073 жыл бұрын
Interesting conversion. I might try this for an old window unit in my garage. Note however that the EER for most window units will be MUCH lower than for a newer "package unit." Most newer window units are 10 to maybe 14. The mini split or "package unit" can be as high as 30. The window unit condenser coils are just too limited in area for efficiency. Be careful, newer units use refrigerants that require pressures approaching 400 psi. The Chinese, in many cases haven't learned to solder or braze the piping to handle this or the vibration involved. I have 2 units less than 4 years old that lost refrigerant from leaking connections.
@rebus5703 жыл бұрын
I been brasing mine up & instead of 410a I use 134 from auto parts it works great. Look up the specs on the model #on compressor mines rated for 410 & 134, same oil, cap tube kinda small for 134 but it works great no change. That is the thinnest tubing I have ever seen got to be very careful with the heat. You can only fix them a couple of times before they get lots of pin holes. It seems to only be the evap coil that dies my condenser coils have never leaked.
@barnowl68073 жыл бұрын
@@rebus570 What??? The working pressure of 410a is over 400psi. That of 134 something around 250psi. It will probably work somewhat but you must be filling the condenser with liquid and the low side pressure must be approaching a vacuum because the liquid can't get through the cap tube fast enough. You are probably paying about twice as much to run and the comp may overheat from lack of cold gas on the input. Are you sure that's a good idea?
@rebus5703 жыл бұрын
@@barnowl6807 Yeah you gotta use a little bit more 134, I charge just till the evap sweats all the way & call that it, suction press only 60 psi, with 90deg ambient, discharge air (evap) temp only 60deg with 76 return air not the best but it works for me, comp runs a little warm but amps in range, suction sweating back to comp case, might research getting correct cap tube size & length for 134, only a cheap 5000btu LG unit though couldnt just throw it away so soon we have to breathe the carbon footprint to manufacture it gonna get all I can out of it. Wish I could get a new coil for 35 bucks it would be better. Thanks for the observation.
@barnowl68073 жыл бұрын
@@rebus570 One of my failed units looks just like yours. LG 5K btu. I may try that on mine. Thanks for the info.
@goiterlanternbase Жыл бұрын
24:19 Just attach tube to both sides and growers supply has you covered😏 No problem finding a used up active carbon filter in XXL, pull out the guts and have some fresh N99 felt applied. There you get the better inline fans too😎
@CET675 Жыл бұрын
I know I am a little late but, thank you. I have been looking for this type of info
@danburch99893 жыл бұрын
Theoretically, you could make this work like a heat pump without opening the case. In AC mode, the cold air comes out the front evaporator into the room and warm air goes out the condenser to the outdoors. If you design a duct system where you can blow the warm air from the back condenser into the room and blow the cold air from the evaporator outdoors. The indoor thermostat can control a damper door to route the air properly (much like modern day cars).
@TinyGiantLifeStyle3 жыл бұрын
Sounds great. However, without an expansion valve the extreme cold weather performance will suffer. It would be interesting to know just how well it would preform though..
@woofdawgg693 жыл бұрын
@@Justnn add in thawing coils and it'll be fine
@danburch99893 жыл бұрын
@@TinyGiantLifeStyle All AC units have an expansion valve. It's always located in the high pressure gas line just before the evaporator.
@heathbecker4203 жыл бұрын
I'll be doing this on my workshop this fall once I find a cheap used window unit on Facebook market or Craigslist. However I think it would be far easier just to set the unit to high fan and max cool and then use a Rainbird temp controller. It completely eliminates all the rewiring and purchase of a relay and separate thermostat (well the rainbird is a thermostat but you don't have to wire it up yourself) so all you have left to is build the connection for the ducts to the unit, then connect them up through a window. It might be a bit more expensive than the relay but its far more plug and play, and that convenience extends to when the actual AC unit gives up the ghost all I would have to do is buy a new one plug it in and modify it to connect to the ducts, no rewiring needed.
@AudioAmbiant3 жыл бұрын
Are you talking about an irrigation controller?
@funnycatvideos54903 жыл бұрын
Did this to ac unit that the analog thermostat was not working correctly. It has digital settings for high and low and plug and play. temperature controlled relay is popular for greenhouses.
@heathbecker4203 жыл бұрын
@@AudioAmbiant no, a thermostat, but they are made by thr same company, Rainbird.
@1juan1673 жыл бұрын
Good job explaining the project, other guys would make it a little bit confused
@redeye6193 жыл бұрын
Its funny that you mention the window units are noisy and rattle, thats exactly why I always call the window ratlers
@rebus5703 жыл бұрын
We used to call them "window shakers" when my dad had an A/C business (1952 to 1965).
@WJCTechyman2 ай бұрын
@@rebus570 Window shakers...I look at my unit and even though there's a roughly 60 Hz buzz and the whoosh of air from my 5000 BTU unit, it's nowhere as noisy as a portable. Those could be called floor shakers.
@Astinsan3 жыл бұрын
The blowers are not designed to push air Through a duct. They just are not strong enough to do it. This is why the other unit is more expensive. You could use a squirrel fan to combat this issue.
@randythomas34782 жыл бұрын
They make 4 inch 6 inch 8 inch inline air boosters. Cheap on Amazon!
@diaperdood93692 жыл бұрын
Thank u so much for sharing your project! This is amazing!!!!
@RobertDickens2002 Жыл бұрын
Very interesting I love this kinda stuff
@Omri.Collects3 жыл бұрын
Great video! You explained everything so that anyone could replicate your build. We’ll done!
@Xx_TheCuriousBrain_xX2 жыл бұрын
Very nice, smart built!
@thetoolmat86323 жыл бұрын
Hopefully a unit Mfg. such as these, watches this video and just makes an off the shelf conversion kit… that would separate their company from the rest of the field! oh want to go back to a normal unit? just unscrew this and put the original back on! - now that would be awesome!
@miroslawkaras77103 жыл бұрын
My hat off for the idea. I am always amaze how people are resorts full. I will do small modification . Instead of making mixing air conditioning I will go with displacement approach. So the air will be drown from outside and and blow to the floor of the room. The hot and stall air will be push to the top of the room and out the a vent. I am proposing that idea because of air quality in standard mixing method. Recently i both air quality meter and i am shock how bad air is when the window air conditioner work and all the windows are close. We actively poisoning our self with our conventional ACs. Any AC with heat/cold air recuperation is the best approach. Any DIY for recuperators?
@f.d.66673 жыл бұрын
Um... not a big fan (ugh - pun alert!) of those foam mountains in the boot and near the fan. Here's why: they will lead to air turbulences, otherwise known as low-frequency noise (LFN) and that's something HVAC manufacturers learned to dread since the 70s. LFN will usually amplify in the ductwork and can't be filtered out through mufflers etc. LFN is long known as a factor that's subconsciously raising your stress level and also negatively impacts sleep quality. If you are building your own A/C, use the opportunity to also make it as silent as possible - across the whole audio spectrum...
@thefirstmissinglink3 жыл бұрын
However he was using non rigid ducting that is prone to muffling such resonance. Definitely agree that he needs to keep it clean though enhancing longevity and efficiency. Might even use the foil tape to smooth out some of the edges and improve flow.
@f.d.66673 жыл бұрын
@@thefirstmissinglink Yup. Agree. Flexible ducting will prevent the forming of standing waves. Good point!
@TinyGiantLifeStyle3 жыл бұрын
Sleep like a baby. Still going strong
@Daft_Dhwelk3 жыл бұрын
I scoured the internet to find a project like this, years ago. For one thing, I have seen window units are much more robust, efficient and lose refrigerant at a much slower rate as compared to the split ones. I don't mind the humming drone of the motor, its like white noise.
@Daft_Dhwelk3 жыл бұрын
A window AC has a single motor - one shaft spinning both blades. Isn't that efficient enough for anyone? Why are window units on the decline, especially in Asia?
@zekemontgomery66783 жыл бұрын
Window units are package units...
@cthorn83553 жыл бұрын
By the very close definition yes. But a packaging is typically heating and cooling.. I saw no modifications to the cooling system to install uninstall a reversing valve is the reversing valve and I saw several overdone situations and more than several underdone situations, People please understand yes we can hack our way through and make things wmake things work but this is a pile of something.
@ryanmalin3 жыл бұрын
Window units are package units without ductwork or a remote thermostat. This was a great conversion!
@Dr.LessCharacter3 жыл бұрын
Bahahahaha true that, he knows just enough to get someone electrocuted! U couldn't prove by me that he's ever done any sheet metal work, or electrical work, or operated a can of off the shelf foam insulation. 197k tweekers now can make they're 1 room AC much less efficient too!
@WJCTechyman2 ай бұрын
@@cthorn8355 If it's a PTHP, then yes, it includes both heating and air conditioning. On the other hand, if it is a PTAC, then that's a packaged unit that ONLY does air conditioning (Of course, these terms are used in reference to the larger siblings to window or smaller wall mount air conditioners and heat pumps like those seen in hotels, retirement living or other uses.
@WJCTechyman2 ай бұрын
@@Dr.LessCharacter Okay, so first, yes, adding hoses to a system makes it less efficient. The electrical work is sketchy but more or less safe. I would have tried to find a way to bring the controls of this unit into the tiny house and into their own electrical box but this may work. That being said, I would have skipped all of this and would have tried to find a space in the wall to put a cavity to permanently mount it without the hassle and risk of voiding the warranty.
@goiterlanternbase Жыл бұрын
KZbin needs more of this brave/hacking type of HowTo's💯
@N674143 жыл бұрын
Great job on constructing. Really clean. Likely it won’t last long because the back pressure on the fan is much greater than it is with an open vent. The blower will fail sooner, but you can always go buy another unit and swap body.
@lawrencelile3 жыл бұрын
Back pressure on a fan causes less airflow, and thus less power. This isn't intuitive, but physics doesn't lie. Source: am air conditioning design engineer. So, no, restricting airflow won't burn out the fan. It could, however, cause the coil to freeze up if the restiction is too severe.
@TinyGiantLifeStyle3 жыл бұрын
It will last as long as the compressor on these cheap throw away units
@N674143 жыл бұрын
@@lawrencelile I agree, it isn’t intuitive but you are talking about inlet pressure. Put you hand on a vacuum cleaner hose and the engine races. No load. This is loaded on the outlet side, not the inlet side as you indicated. You are probably an hvac designer. Nonetheless it was a clean job. Most don’t do it this well. It’s common for these solutions to be used by aircraft mechanics to pump cool air into jets while working on the ventless interior. The home brew units fail quite quickly. As the guy said below. “Disposable”
@royurick3 жыл бұрын
Heard the phrase "and learn to build a solar system..." and my first thought was "why on earth would you need to learn to make a diorama of the sun and planets as an adult?" Then I realized what you meant. LOL
@Rob83 жыл бұрын
You can get rubber grommets to protect wires that pass through sheet metal.
@craigtate59303 жыл бұрын
Very clever idea
@peterrogers16163 жыл бұрын
A small in duck booster fan on that supply would help with the additional static pressure that your blower Lacks
@rickdworsky64573 жыл бұрын
duct, quack quack
@peterrogers16163 жыл бұрын
Yes very good
@dadedubbledee3 жыл бұрын
What about separating the parts and make it into a small coil and separate condenser? Something I have thought of trying many times
@michaelmartinez45153 жыл бұрын
Same here, but it would require the Freon to be discharged and then when connected/soldered back it would then also need a vaccum and recharge, i figured if i removed the actual fan inside that cools the condenser i could attach and wire in one of the 10" or 12" 12v radiator fans attach it to the back of the condenser and it would cool it perfectly, they're very slim fans only being a couple inches thick.
@bbranett21883 жыл бұрын
Why not just put it through a wall? They are made for that. Wont void the warranty...You can make a pink foam winterizing box
@Ivan.Wright3 жыл бұрын
He explained that in the beginning. He didn't want a wall unit. He wanted that type of unit but they're expensive so he made it himself. Most diy-ers don't mind voiding warranty when they're saving so much making instead of buying. Besides, if a product like this doesn't break down within the next few weeks you probably won't ever need to take advantage of a warranty, and the day that you do will be the day after the warranty ends.
@RedfishInc3 жыл бұрын
Noise, by removing the ac unit to the outside and just running the ducts you can reduce the noise of the compressor and fan to almost nothing. This would be ideal for something like a teardrop camper where the overall interior volume is very small and even the noise of a small 5000btu a/c unit could be intolerably loud.
@TinyGiantLifeStyle3 жыл бұрын
Quiet Sound, Small easy penetrations ect ect. No large hole in building that will not fit next years model.
@paulsto65163 жыл бұрын
And the AC will run more efficiently.
@goiterlanternbase Жыл бұрын
17:55 Not necessary. The foam will never let go, if both surfaces are primed with acetone. With the screw hole, you just had made a ingress point for rust. Just use magnets to hold the parts in position until the foam has cured.
@macdaddy222503 жыл бұрын
I would also install a inline booster fan, the fan on the air conditioner is crap but I'm not mad at all with this hack. Turn it into a mini split then I'll be impressed
@dallynsr3 жыл бұрын
The title or sub title to this video could be how to make a package unit in Cuba. They still use cars from the 50’s and use hot diesel vapor from a copper tube pointed into the carburetor to chug those old cars around. Cause communism is wonderful. If all I had was a window unit, could see re-purposing it like this cause we can. But why? I install mini-splits and would NEVER recommend this as a viable method for a tiny house or shop. Uses way too much power and has very low btu exchange. (At least here in the hot summers So Az)
@patrickday42065 ай бұрын
Now solder in a four way switching valve and you also have a heater
@bigsid19843 жыл бұрын
What an amazing idea. We need more
@rebus5703 жыл бұрын
Such a complicated mod. I took an old timeclock can & put a 30 amp compressor contactor & 24volt transformer in it, got a 6' appliance extension cord, cut it & connected female end to load side of contactor & male end to line side, 24v trans to line side, fused 24v side & got a snap action manual thermostat on wall. I plug appliance xtension into outlet & plug A/C into box & it turns A/C on & off with wall thermostat no mod to A/C, no matter what unit you get just plug it in like normal & set fan speed with existing controls & go. In 14yrs its never failed me & its easy to change & use different units when they die, I have used 5000, 10,000 & 12,000btu units with it even digital control units work fine. I use as conventional window unit no duct work but you can duct it if need be.
@jamesf20393 жыл бұрын
Much simpler 😌
@jameswest97923 жыл бұрын
Send a picture! Thanks!
@ken482293 жыл бұрын
I don't even see what's the point all your doing is extending the ductwork
@TinyGiantLifeStyle2 жыл бұрын
Tiny tiny room
@beblissnow59473 жыл бұрын
I guess I don't understand...why not just run the air-conditioned as is.
@TinyGiantLifeStyle2 жыл бұрын
Tiny room, noise, vibration, ect
@SmartEasyDIYer5 жыл бұрын
Interesting project! Thanks
@TinyGiantLifeStyle5 жыл бұрын
Your welcome
@Mikesdear3 жыл бұрын
What’s the static pressure on that supply duct now? I’m curious if the blower motor will make it with static it wasn’t designed for.
@Eric2300jeep3 жыл бұрын
I was thinking the same thing. Would probably be a good idea to put an inline booster fan
@TinyGiantLifeStyle2 жыл бұрын
Still working. Didn't measure the pressure though the ductilator would give the answer
@airconmantv3 жыл бұрын
You can refer on the circuit diagram to determine the wires where it goes and what its connection for
@TinyGiantLifeStyle3 жыл бұрын
yes, exactly
@TofuInc3 жыл бұрын
Minisplit is a much better option. If that's too expensive or you not wanting to mount anything, a portable unit can be purchased for the same cost as the window ac + the materials shown. And it will still have the warrantee.
@VealCalf13 жыл бұрын
Portable units suck...outside air into the space you are trying to cool. Most of them use inside air to vent heat outside, thus creating negative pressure, and forcing outside air into the space you are trying to cool. Technology Connections has a great video on this.
@TinyGiantLifeStyle3 жыл бұрын
portable units often pull large amount of outside air into the structure making them very inefficient and humid if in a wet climate. I do like mini-splits better. IF you can hit a sale and get one for $300 bucks its gold.
@zakksrage3 жыл бұрын
I paid 165$ at Home Depot for a portable ac that’s on wheels. An has a duct that goes to the outside. No mods needed. Also it’s 8,000 btu an looks modern an nice
If hank iff king of the hill was real 😅 good video
@caddyguy53693 жыл бұрын
I've been wanting to add an external thermostat.
@TinyGiantLifeStyle3 жыл бұрын
Go for it!
@romantheempire22545 жыл бұрын
Please provide schematic diagram before and after for verification. Thank. You
@williamwixon3 жыл бұрын
Phenomenal! Fantastic! Thank you so much!!
@huntmechanicalventilations49293 жыл бұрын
Why not just cut a hole in the house put the air conditioner in retain your factory warranty and not create all the static pressure with the flex duct and sketchy connections?
@peterrogers16163 жыл бұрын
Maybe a cheap little 6-in inline booster fan on that flex would be the ticket
@ckm-mkc3 жыл бұрын
You would do this to move the noise out of the house, it's a cool, cheap hack to get that without buying a mini-split for $1000 (which still has a fan inside). Probably way less static pressure than the original which was forcing the air to do a 90 degree turn right after the fan. And if you use a 6" duct, it will have more surface area than the original outlets...
@Ares-jx4ep3 жыл бұрын
yes, that incredible factory warranty on cheap window A/C units is worth far more than cutting a hole in the house for said unit......smh. What if the "building" you want to cool "isn't". Lets see... cut a hole in a tent for a window A/C... yeah that'll work well. What if you want to cool a stone/brick/concrete structure? What if you don't own the building? "Hey Landlord, I'm sure you don't care that I just cut a hole in this wall I don't own."
@TinyGiantLifeStyle3 жыл бұрын
NOISE, large hole that will not be the same on next years model. Also, its a $97 throw away Walmart unit. Couldn't care less about the worthless warranty.
@hellhound13893 жыл бұрын
A few years ago I put AC in my workshop/ shed. It looked easier to do what I did and just cut a hole in the wall and frame it in
@flanny7013 жыл бұрын
the whole point of this is for if you dont want to deal with the noise of the compressor and fan of the ac if you dont mind it then this is all redundant just throw it in a hole in the wall like you did or a window
@slacky43583 жыл бұрын
I am an HVAC guy and I did the same thing to my RV lmfao except I had to put a delay switch on the compressor because it was tripping breakers
@TinyGiantLifeStyle3 жыл бұрын
The thermostat I used has a short cycle delay time that can be programmed. Good point though.
@KentuckyFriedFixes3 жыл бұрын
Have you ever wondered why your neighbors might pray for your ruination?
@TimFuller3 жыл бұрын
Cool. You got me thinking the entire rip it apart to bypass internal thermostat and select fan speed is redundant if you just set it on high and leave the existing thermostat maxed. You could still build an external relay-thermostat unit but you'd never have to mess with the guts inside that unit which would put some people off. #hobomessiah
@twoeightythreez3 жыл бұрын
He sets it up this way so you can use a standard house thermostat to set and forget the temperature.it’s basically central air for a tiny house.
@ownjam3 жыл бұрын
This is a great idea but you can find a 110-unit like this that also has a heater on it it's about $350 on eBay
@goiterlanternbase Жыл бұрын
The first thing that has to go in such a unit, is the fan😉
@sjr78223 жыл бұрын
The host is very good at explaining and instructing, but, Clearly, my brain isn't wired to understand this, I was with him for 7 minutes before my eyes started twilling. Anything with math, I have never 'connected' but, I'm still curious and envious of those with the talent to Get-r-Done
@mortneff46743 жыл бұрын
I like the idea and concept but wouldn't it be better to hook or use a ceiling fan & Light remote control to it! there for by passing the need for the 24V box!
@Chad_White3 жыл бұрын
This is great..would be great for a camper.
@jerryrigsit54003 жыл бұрын
Maybe for a 10,000btu unit. Not smaller. Might be usable for a skoolie or a revamped camper
@chrischappell71173 жыл бұрын
Nice informative video. I don't know if I missed it but what is the advantage of doing this vs. just installing it in a window or making a hole in the house and installing it there? Just trying to understand why doing this VS. just installing the window unit. Thank you.
@kellypophamjr57773 жыл бұрын
Noise
@ionstorm663 жыл бұрын
To add to this, the compressor makes most of the vibration and noise. Moving it further away, especially with flexible ducting, will make it much more quiet. Also packaging. You make want to move air around a space, a ductless unit is very poor at circulating air in a room, it just sucks the air right back in.
@TinyGiantLifeStyle3 жыл бұрын
low noise and a small hole through the building.
@marctorr55513 жыл бұрын
Been looking for something like this, thank you!
@TinyGiantLifeStyle3 жыл бұрын
Glad I could help!
@wyldanimal23 жыл бұрын
at 5:33 notice that one is Non, and the other is Ins. you use the Non for Bare metal non insulated crimp ons, and the Ins for Plastic Insulated crimp ons. you Used the Wrong one.
@Lierofox3 жыл бұрын
Came to mention the same thing. The Non-insulated opening tends to shear through the insulation when it crimps, exposing the metal on the connector and partially negating the purpose of the insulation.
@thereynolds27253 жыл бұрын
Yes, but the non-insulated is a better mechanical connection. As this is all enclosed inside a housing, it really isn't an issue.
@davehoward36453 жыл бұрын
Nice video! You seem to be very knowledgeable on the subject. I have a question if you would be so kind. I was inspecting my outdoor unit and didn’t pull the power, as I took of the cover it contacted one of the contractor wires? It now doesn’t work. It seems the contactor still works but it doesn’t turn on although I can hear a slight hum. What do you think I need to replace?
@ken482293 жыл бұрын
A couple different things 1. check or replace the fuses in the disconnect. 2. The power going to the disconnect comes either straight from your meter or from your electrical panel in the basement check those breakers.
@TinyGiantLifeStyle3 жыл бұрын
post a video/picture
@Rush501013 жыл бұрын
Great job on a very useful idea!! Thanks
@TinyGiantLifeStyle3 жыл бұрын
Glad it was helpful!
@boysrback56903 жыл бұрын
Old bread knife is your friend for foam.
@Adam-uo2mc3 жыл бұрын
Please do not just cut off the unused ends and wrap them in tape, this is extremely dangerous electrical tape is not meant to be used as a insulator on it's own. Instead crimp on a dead end or a coupler or use a wire nut then tape them up to keep them out of he way.
@peterrogers16163 жыл бұрын
Ok lame
@Adam-uo2mc3 жыл бұрын
@@peterrogers1616 If you want to die in a fire this is one way to do it. A poor connection under the tape will cause excess heat that regular tape can not handle so it will just melt, There is more expensive tape that can handle high heat but it's cheaper to use wire nuts. If you personally want to risk it that's up to you. I'm just giving people some important safety advice.
@thefirstmissinglink3 жыл бұрын
Was cringing when I saw him wrapping up the ends with tape. Shrink tube came to mind for the cut ends.
@TinyGiantLifeStyle3 жыл бұрын
That is NOT what was done here. Look closer.
@thereynolds27253 жыл бұрын
There are no connections insulated with tape.
@1987FX163 жыл бұрын
Nice, almost a 50% savings doing this. Your could have 2 5000BTU ac units for the price of one off the shelf unit.
@almeal4065 ай бұрын
do you run the air supply and return lines to the same room?
@barrybretz60733 жыл бұрын
Two relays of the same kind would allow you to leave the fan on independent of the compressor
@chadelmore693 жыл бұрын
We talking about a/c and a/c accessories?
@bobbyruchalski23683 жыл бұрын
Curious if this unit is still working/cooling properly right now? I had a situation where I had to do this same thing years ago, so this video can be helpful to people. Mine worked for a summer than gave out/broke. Don't know why it broke quick, ductwork seemed large enough.
@TinyGiantLifeStyle2 жыл бұрын
Yes it working today
@p1epoppa3 жыл бұрын
The American Way 😎💪🏽
@whydontyouaskme5 ай бұрын
I thought you were going to split it apart and leave the outside parts outside and the interior parts inside.
@goiterlanternbase Жыл бұрын
18:23 It's not like a glue, it is a glue🤣 That's why i said earlier, the screws are not necessary. This will never come apart until the metal is rusted away.
@BillSias-op7xw3 жыл бұрын
Why not just extend the wiring from the original controls and mount the thermostat and fan controls on a switch plate further away, duct as you have shown?
@BigDmike243 жыл бұрын
Set unit settings on high.Use an inkbird control the temp. No wire hacking required.
@funnycatvideos54903 жыл бұрын
i thought the exact same lol.
@jameswest97923 жыл бұрын
@@BigDmike24 …. What is the Inkbird product? Thanks!
@BigDmike243 жыл бұрын
@@jameswest9792 ITC 308
@jessepalmer69973 жыл бұрын
Awesome great job!
@MikeJones-mf2rt3 жыл бұрын
The $549 package unit provides heat as well though, no?
@TinyGiantLifeStyle2 жыл бұрын
Sure
@dopeymark3 жыл бұрын
Smart stuff. Good stuff.
@jlowell552 жыл бұрын
So if your getting the cold air from the top of the unit, what was the purpose of putting the extra piece on the front? After watching 5 times, I still do not understand that.
@TinyGiantLifeStyle2 жыл бұрын
Return of indoor air. Otherwise you waste energy sucking in hot outside air
@redneckgaming973 жыл бұрын
How well did it work when u hooked it up IV been trying to something like this for my camper I'm thinking about trying it the way u did it cuz I want to hook it in to the heat ducts in my camper since I removed the furnace
@TinyGiantLifeStyle3 жыл бұрын
It works well to this day. Just get the duct size correct and use vinyl duct for sun exposure
@treeguyable3 жыл бұрын
I was noticing, a lot of comments on here, include shity, for shitty, realy for really, no capitalization for sentence beginning words, no punctuation. I guess commenting on how the job is done improperly, while improperly writing such, is to be expected in the tidepod generation.
@jimsteele71083 жыл бұрын
A good idea
@blainecelestaine45433 жыл бұрын
You the man.. I was about to do this and found your vid thx
@TinyGiantLifeStyle3 жыл бұрын
your welcome! Thanks for stopping by
@richh99043 жыл бұрын
Did you use class 2 low voltage wire in a 120 volt circuit? Danger Will Robinson.