Orbit Anti-Siphon Valve (57623) Features and Troubleshooting

[@ronaldkammeyer9143]

FOR REAL!!! Bought one of these valves (NEW), installed it and the drip lines from this valve would not stop dripping. After much trouble shooting other portions of the valve shown here on YOU TUBE, I started switching out parts from another "NEW" valve. I found that the plastic "seat" the solenoid screws into (a separate piece of its' own) that screws into the valve housing had a hairline crack that allowed water to flow even when the valve was off. Solenoid was fine. Also no replacement parts available so get ready for another valve purchase and a spare parts source. Check proper assembly alignment before buying. I may have seen the piece I reference had an issue because it was canted in its' mount spot. Awesome valves over all.

[@tyroilsmoochie-wallace6900]

I had a leak at the soleniod. I followed these instructions...disassempbeld, cleaed and reassembled... and BOOM! no more leak! You just saved me $40.00 because I was about to replace the whole valve! Thank you!!

[@jasonbodenheimer4017]

Thanks for this very detailed and thorough walkthru! I inherited an irrigation system and nothing is labelled. After watching this, I decided to order a completely new manifold with 4 brand new valves... and with ronald's comment below, I will be inspecting each valve prior to installation to confirm they were assembled correctly.

[@paulaguilar5041]

The 2 most common problems are the diaphragm goes bad especially if it gets a lot of sun. I’ve had to replace all of them at 1 time or another. The other common problem is valve metal piece inside of the spring on the valve goes bad. Sometimes you can clean the rust off it and it will work again. But by far the diaphragm is the most common issue. A small amount of water will trickle past the diaphragm, you can actually hear it if is quite. Also the sprinkler at the end of the line of that valve will be on slightly. It may manifest itself as a very wet spot on your lawn.

[@cindys176]

I did as suggested for my valve that won't automatically shut off. I think I saved myself $300 (that includes replacing all the valves). Maybe I'm delaying the inevitable but at least it works now. Thanks for the video!

[@binzsta86]

what did you do to fix it?

[@woolval52]

How I wish I'd know about those connectors at 5:28. I'd have spent a few extra dollars to have the ability to swap out the entire valve without cutting and gluing PVC. My spacing and alignment make it very difficult if I have to cut PVC. Please have your vendors recommend these adapters whenever someone is installing valves. Although, it's a bit late for me... bummer!

[@jfc650]

Can you tell me where to buy these PVC connectors?

[@wade727nelson]

Ditto.

[@trevaush]

Thank you, Trace. Very informative. Saved my life (and sprinkler system).

[@ElSparky310]

Thank you for this video. Rare to see from a manufacturer, especially a video with such detail. From now on orbit is the only brand i will go wiirrfor my irrigation needs

[@wade727nelson]

The super hard water here in Phoenix will sometimes clog the diaphragm with diamond-like calcium crystals. Disassemble, remove crystals, re-assemble. Symptom is not shutting completely off.

[@cappysheeley5311]

Very helpful, the only video I found that addressed the anti-siphon leaking

[@mikrch3935]

Well glad I watched your video. Right at the beginning you mentioned the correct water flow direction and I . I had it on wrong. Thank you !

[@howlingc5952]

This is the best DIY irrigation video on KZbin. Nice job Orbit!

[@bobabend8186]

Comprehensive and EXCELLENT video. Saved me lots of time and trouble!

[@waynebird3218]

I'm watching this video to fix a new valve. Thanks orbit. Qc is a self installed feature

[@lonnielathrop9816]

Thank you! Saved this ol’ gal a lot of time and money!

[@d.mcfadden7759]

Very helpful, I suspect I have freeze damage or perhaps merely some sand. I'll check for those issues before assuming I need to replace all my valves.

[@rower41]

This is a great video... I'll always by orbit when I can because they took the time to do this. Very cool.

[@wayneporter2037]

I didn't like the look of having the valve assemblies heads jetting up our of the ground. After purchasing a vault, I placed them about 8" underground, only to learn the hard way that water started pouring out of the syphon heads once shut off. Basically, the system would backflow into the heads and fill up the vault with water. - This issue is EASILY fixed with the addedd installation of a 1" PVC back flow valve on each leg to stop the reverse flow of water back to the heads.

[@PintlerMedia]

Same experience here, although it took 4 years before acting up.

[@wesleyjonathan2805]

Love this video.It was said at around 2:50 that the anti siphon valve could leak if “you dont have anything connected down stream”.Would that include say a broken sprinkler head near by?If that’s what that means,should I have fixed that 1st.Cuz I replaced the anti siphon valve top with new O rings etc.And it still leaks just like this video.I was going to do the whole valve assembly next.However if I can avoid cutting pvc, that would be ideal.

[@jlmag6710]

Sorry for asking, I have the same issue right now, how did you fix yours ? I don’t understand when it says it may still leak if there’s nothing connected downstream.

[@rondie.x53]

You are very thorough and easy to understand thank you

[@johns6326]

Great video, very helpful. Does Orbit make the swivel-adapter-with-o-ring/ for 3/4" PVC pipes?

[@kennethshiba8295]

My sprinkler system is hookup to automatic timer system but after the sprinkler is finished its cycle the pipe makes a big bang. It’s always after the all the cycle is finished

[@BoyFrom_Paris]

At 5:13, what do you call that green-colored threaded adapter that connects the PVC coupling to the anti-siphon valve?

[@user.A9]

Bought two new 57623's yesterday and one has a leaking solenoid. O-rings look good and solenoid and rotation adapter are tight. Why don't these come with the quick disconnects shown at 5:21 in the video? I will have to cut the pipes to get this valve out to take it back to the store. What are those quick disconnects called? Is there a part number?

[@orbitsprinklers]

Hello, those parts can be found here: store.orbitonline.com/store/products/1-1-4-female-butress-thread-x-1-male-pipe-thread-swivel-adapter-with-o-ring/

[@losusmil]

Anti-siphon starts leaking after the sprinklers are turned off. Follow the same troubleshooting that you mentioned at 2:25?

[@orbitsprinklers]

Hello, this could be due to some damage or some other cause. Please reach out to us by private message via one of the social channels and we'll get in touch to find any possible fixes.

[@JabFreeMcGee]

Of the 3 anti-siphon valves I have on my system, one of them turns on when I supply water to the system even though my sprinkler system is off. I had a brand new one, so I replaced the whole thing and kept the old one for parts, but still have the same issue. I’m wondering if one of my main valves has a bad solenoid or diaphragm. That’s next to check, even though the main valve is only a year or two old

[@myoneblackfriend3151]

Is there a video for setting this up after it is installed? If I manually turn the valve on by rotating the black switch (solenoid) it works fine. If I use the electronic controller the flow is dramatically lower and nothing comes out of the sprinkler head.

[@rigogarcia3960]

Very useful video. Thank you Orbit!

[@ivancossiochavarria]

I have two 57623 valves. on one of them when the sprinklers turn on the solenoid does not make any noise but on the other the solenoid makes like a buzzing sound do I have a bad solenoid this is a brand new solenoid

[@orbitsprinklers]

The sound often present. As long as it's opening/closing as expected it is good to go.

[@BigBilly1958]

Requesting part number for lid sub assembly. I replaced the diaphragm and water continues to leak through the valve body.

[@bruce-le-smith]

I recently got your 4-in-1 (Orbit DripMaster 67790 4-in-1 Drip Irrigation Valve), and I was hoping that I didn't need to use the electrical wires right away. I would love to find some approved documentation confirming that idea. In this video it seems those two wires are designed for low power signals to enter the unit and move a valve, but there is a manual bypass for that sub-system. Is my logic sound, can I ignore those 2 wires until I reach the point where I want to get a fancy timer that sends signals to a unit like this?

[@crabapple6775]

to check the diaphram, is it either 'it works' or 'it doesn't' , or there any in between, iffy area?

[@Davilow]

What's the small piece of metal that he pulls out of the valve at 6:54? It looks like a staple. Is this a part that should be replaced every time the valve is disassembled?

[@orbitsprinklers]

Hello, good eye spotting that. That is not a part that should be in the valve. In fact our team used that to prop open the internals to simulate the symptoms of a leaking valve. These 'staples' are not in the original.

[@okkealberda]

Have a leak at the anti syphon valve but I have not found a replacement part of the rubber ring. Also not at the Orbit website.

[@sarcasmopro]

Is it this one? www.orbitonline.com/product/replacement-o-ring-for-rotation-level

[@tbc_2024]

is it possible to add a slow acting solenoid to reduce water hammer starting & stopping zone?

[@gilbertmatzdorf9534]

Wish I could find that union they use between the valve body and the PVC piping above the butt connector. Makes the valve replacement or servicing a bunch easier. Anyone know where to get those unions shown in this video?

[@jfc650]

Do you know where I can buy these PVC union?

[@SChan-nw3wk]

Thank you. very helpful video. My rotation adapter is cracked. I wonder where to buy this part. I tried Home Depot, Lowes and Amarzon, they don't sell this part. My original problem was leaking on all of my sprinkler heads while the system was off. Should I buy a new set instead? Pls. adv. Thank you.

[@marylamb6063]

Can I connect it without connecting the solenoid and use it as a manual anti-siphon valve? I have one installed but it's not for an individual valve. It's above ground.

[@orbitsprinklers]

Yes, this can be done.

[@ruthven78]

thank you, friend's valve started leaking and was wondering if I could fix or if they would have to call a service. So I'll at least troubleshoot it to find the cause

[@francesluo6324]

Does this valve go with any automatic timer, including smart b-hyve controller? Any DIY video link to how to wire it will be highly appreciated!

[@RascalCatify]

What happens or what could be the issue if I cannot place valves 6" higher than a sprinkler head? In one case I would need to have the valve about 4 feet off the ground maybe more.

[@michaelhudock8426]

Is it typical for the anti siphon valve to drain water when the system shuts the valve down?

[@JohnDoe-yq8ox]

It could be back flow water. They recommended having it at least 6 inches higher then the highest sprinkler. I think that is why.

[@chrishendrickson9035]

Extremely helpful. Thank you.

[@Zamboni-0805]

I noticed in the video @6:23 that the valve was model 57624, are they the compatible with the 57623?

[@orbitsprinklers]

Yes, the 57624 is the 1-inch version of this valve. the 57623 is the 3/4-inch inlet and outlet.

[@johnnylove6403]

@@orbitsprinklers Thanks

[@533lpunit]

@4:04 what size o-ring is that?

[@sarcasmopro]

www.orbitonline.com/product/replacement-o-ring-for-rotation-level

[@ShakyKeys]

I just replaced three old Anti-Siphon Valves with new Orbits, all connected to an automatic timer. Two of the three work fine, but the third one does not shut off automatically. If I tap the anti-siphon side of the valve with my knuckle (like knocking on a door), the valve closes. It's acting like it's sticky... I've disassembled and inspected/cleaned and everything looks okay. Any other suggestions? Maybe I just have a bad valve?

[@orbitsprinklers]

Hello, this sounds like a bad solenoid. Please reach out to our support team and they will get this resolved: www.orbitonline.com/contact-us/

[@301steady]

What is the name and part number of those threaded couplers attached underneath the anti-siphon valve? I want to install the quick disconnects so I can work on the valves, or replace them.

[@testrak]

Orbit 57199 1-Inch Manifold Swivel Adapter

[@jlmag6710]

Anti siphon lid is leaking already check seals and they look good I even change the whole lead with another that is good and still leaks, what do you mean when you said it might still leak if there’s anything connected downstream? Do you advise to replace the whole valve? I don’t really want to do that since is not an easy fix for me.

[@Dense147]

I just bought all new valves and 2 months later i have a valve that leaks internally. I have a puddle around a sprinkler I tightened the manual valve and checked the diaphram and everything looks good but im still getting water leaking past the vallve

[@orbitsprinklers]

Hello, we're sorry for the issues this is causing. Please send us your contact info via a private message on one of our linked social media accounts and we'll get in touch to get this resolved.

[@Dense147]

I ordered from amazon and they sent me a replacement for free no questions asked. All I did was swap the tops with the diaphragm assm and fixed my issue. I confirmed this was my problem by swapping them around on my existing vales

[@jfc650]

Nice video! I have water leaking in anti-siphon lid. Where I can buy the siphon lid, O rings, and other parts? Please provide links to buy the parts. Thanks

[@RonaldRichards-o3n]

I have an automatic conversion valve kit that screws into a brass manual valve. I have used these for many years. This year the valve seems to work but I get a very small rate of flow. Using the bled valve does not turn on the valve and there is no flow. The flow control is fully turned on. What is the problem?

[@herekitty6309]

Great video, so much information, may I ask if this is hard wired to the orbit auto system or is it connected to house power, if my system is unplugged, can I safely detach wiring, from fpt anti-siphon valve?

[@myoneblackfriend3151]

Hello. You will not need to wire these to the main power on your house. They get wired into the controller. They make special cables for the controller. Each cable will have several colored wires inside. All 6 of my valves use the same ground wire from the controller and one unique color. Connect each solenoid the the ground wire. Connect a single colored wire to the other side of the solenoid. I have labeled each valve in my manifold. Attach only the wires you used to your controller. Program your controller and enjoy.

[@mattpolitzer2920]

Nice video. Only thing I didn't get is how to test the solenoid function. My valve works in the manual (non electric) mode only. Thanks for the other malfunction and remedy information. I'm smarter now on the anti-syphon valves and can repair them myself.

[@ReneUhlver]

Did you find out why of it your solenoid wasn't functioning? I have the same problem that started today, it won't go manually watering, only if I mechanically rotate the black valve. Thanks!

[@byronlastrapes6979]

I have a six valve assembly resembling a V6 engine. Three of my valves that are on the same side has a partial/restricted flow at start up. When I shut of the system manually at the main shut-off valve several times; the flow is restored to full pressure. After watching your video, I disassembled and flushed each valve one by one. So far this appears to be the cure. Do you have any ideas why this problem occurs. Thanks for your help.

[@orbitsprinklers]

Hello, we're not able to diagnose what is causing this based on your description. our support team would need more information. If you could send us a private message on one of the social media channels in the description we'll get in touch.

[@alxv213]

How do I turn off the music in the background?

[@floresf2198]

Skip the video

[@ramonleon5175]

😂😂 it's a cool little jam bro why do you wanna mute it jk

[@guillermolettierigalland8559]

My valve won't turn on, it's a new one. I can hear a click when I send a signal manually from the timer, but it doesn't turn on, what could it be? Actually, I hear 2 clicks, and nothing happens.

[@naamangeist7843]

It could be a number of things but the most common is a bad solenoid (Orbit part: 57041), either on the anti-siphon valve or on the in-line valve after it. The best way to test this is to turn it on manually (both anti-siphon and inline valve). If the sprinkler works, it's likely the solenoid, unless you have it wired wrong. These can be purchased on Amazon for $6.60 with free next-day shipping for Prime members. If that doesn't do it, take the 8 screws out and inspect the diaphragm and clean out any debris. Also make sure your flow control knob isn't closed. Turn counter-clockwise until it stops.

[@pyromonkee2510]

My anti siphon lid keeps popping off when I turn the sprinklers off. It also leaks like crazy even though all the sprinklers pop up.

[@orbitsprinklers]

We're sorry to hear this. Please reach out to our support team and they will get this resolved: www.orbitonline.com/contact-us/

[@jasonc9049]

Where can I purchase the replacement seal carrier?

[@naamangeist7843]

Good question. Did you ever find the answer? This guy sure isn't any help either.

[@rogelioherrera3746]

My valve only works manuel but won't work in automatically what do I need to replace?

[@orbitsprinklers]

This sounds like a problem with the solenoid or wiring. Please send us your contact info via our social media channels and we'll get in touch to help find the right fix.

[@myoneblackfriend3151]

@@orbitsprinklers Orbit should be making videos to address these questions as the same ones pop up just like your sprinklers.

[@GuitarsAndSynths]

Excellent video on how to understand the anti-siphon valves. Unfortunately three of mine are leaking at main body and replacement is the only viable option.

[@CTWhalen]

Really excellent quality video!

[@michaellamere1250]

Does this apply to the 57624 product?

[@jfc650]

Where I can buy the PVC union pipe fitting adapter?

[@andrewjou9835]

My valve would not turn on either automatically or manually and it's getting worse gradually till no sprinkler head will pop. There's no leaking and I changed the diaphragm plus cleaned the inside of the valve but still not working. There's another exact identical valve side-by-side working fine so I made sure I assembled this one back correctly. Could it be a bad solenoid? I thought a bad solenoid should caused by electrical issues. Somer one please help. I can't afford to hire a professional guy since I lost my income since the pandemic.

[@orbitsprinklers]

Hello, we're sorry to hear this. Please reach out to our support team and they will get this resolved: www.orbitonline.com/contact-us/

[@bwyeung]

Extremely helpful!

[@mariomora8303]

Hello..installed 2 .manifolds and water stays on..did you say it might be backwards ? Thank you..

[@barbarareal5224]

I can't get my Orbit sprinkler to work, shows no AC, what can I do?

[@orbitsprinklers]

No AC indicates power is not getting to the timer. Most our timers have a battery that works as a backup to keep programming in case of power outage, but isn't sufficient to actually run the timer and operate valves. There could be a number of reasons why power isn't getting to you. Please contact us through social media (private message) with your contact info and we'll get in touch to help figure out the exact cause of the problem and a fix.

[@guntursitumorang6897]

how to get the spare parts?

[@hotwhelrob]

How do I Handel a situation where the heads are higher than the valve?

[@orbitsprinklers]

In that case your anti-siphon will not work. They need to be at least 12 inches above the highest head.

[@chetjohnson3335]

@@orbitsprinklers but the video said 6 inches. The video also shows measuring from the ground and not from the raised head.

[@bobritchie8644]

MY valve drips water at the 2 lowest sprinklers. Not fast but enough to run down the gutter on the street .Is this diaphragm?

[@orbitsprinklers]

Yes, this sounds like a diaphragm of a solenoid (which isn't closing the diaphragm fully). If you'd like to pass us your contact info via a private message on one of our social media channels (linked in the description) we'll get in touch to help find a fix.

[@dinoali387]

Where I can purchase adapter under solenoid. My kids twist hard and brooke plastic adapter under solenoid now I can't screw solenoid Thanks

[@4PeTe2]

So where do we buy the replacement parts? Orbit website gives no place to buy replacement parts

[@orbitsprinklers]

we provide replacement parts at our online store: store.orbitonline.com/store/products/category/replacement-parts-sprinkler-systems/

[@californiambamarketing4500]

Great video! Solved my problem - thanks!

[@lhatslc]

Wow, how about if it won't turn on?

[@orbitsprinklers]

This could be a number of reasons (too many to make a definitive determination here). It could be a short in the wires, a bad solenoid, a bad timer terminal, etc. Please pass us your contact info via private message on social media and we'll get in touch to help.

[@lhatslc]

I don't need help on why it will not turn on, just thought the video should have something on it. Great video just missing a simple wiring statement for what if. On my issue. The manual on works so line is clear. I swamped the solenoid out with a working one still dead. Checked the wires with VOM. The timer is 19yrs old so best guess is its bad. I have 8 zones one dead after I rebuilt it last year.

[@alexle7964]

Everything work but every time I turn on and or off the anti siphon always leak. Any suggestions?

[@ruthven78]

I'd try replacing the seal and if that doesnt fix it then consider replacing the whole valve assembly, they arent that expensive and often only a lil more expensive than the individual replacement parts

[@preetsingh694]

Every time my indoor control unit turns on, I hear a click on the valves but they doesn't turn and the indoor control units resets itself including times and dates.

[@synnex20]

great video thank you!

[@jessesotomayor4843]

Great information but get rid of the music

[@winstoncote]

So how do you replace the entire valve?

[@orbitsprinklers]

Depending on how it's attached it might be as simple as unscrewing the valve. Please reach out to our support team and they will get this resolved: www.orbitonline.com/contact-us/

[@gadzukis1018]

how about when the valve is on only a trickle of water comes out.

[@orbitsprinklers]

It is normal for the a little bit of water to trickle out of the anti-siphon portion. If you mean that when the valve is on your sprinklers are only having a small trickle of water, that would indicate a bigger problem. In that case, Please reach out to our support team and they will get this resolved: www.orbitonline.com/contact-us/

[@naamangeist7843]

A parts list would have been useful. "Replace... or install a new one" is only half the information needed.

[@MIND9988T]

Do u want ur job done too?? 👎👎👎

[@naamangeist7843]

@@MIND9988T Umm... yes, I would! That's why I need the part numbers... Derp!

[@dzerres]

where's that little black "bleed" screw? THAT's what I always have trouble with: too far out and it leaks and too far in and the valve turns off!!!!!!!!

[@therealandrewcano]

Winterize , we don't do that in Goodyear Arizona.

[@michaelpmusgrave]

Thanks! Helped a lot.

[@onelogue]

Very helpful! Thank you!

[@mary74724]

thanks

[@rondie.x53]

excellent !

[@thnkless8242]

Close. Water doesn't make it to sprinklers. Everything seems okay

[@chori63]

thank you.

[@drueatcer]

Mine won’t turn on.

[@temotorres4097]

Just clean with running water inside you'll see mildo come out

[@F0reverYoung]

4:55 thats what you get with plastic eh

[@SuperGreetings]

I bought THREE Orbit sprinkler valves two weeks ago. I installed one and it leaked immediately. Last weekend a second one sprung a leak. Two out of three leaking within days!!! I am DONE with this brand after being loyal for years.

[@orbitsprinklers]

Hello, we're sorry to heat this. . If you could send us your contact info via private message on one of our social media channels (linked in video description) we'll get in touch to resolve. Thanks.

[@michaelmcgillivary9268]

this is very helpful, but just once I"d like to see the guy kneeling in his front yard at an actual valve that is attached on both ends and doing this.....

[@beckysimpson3518]

Get rid of the stupid, repetitive music, because I can't hear the guy speaking. If I turn it up loud enough to hear what the guy is saying, the music hurts my ears. This material is exciting enough to stand on it's own, without background music. And background music should be BACKGROUND music, not louder than a human voice. >8(

[@MIND9988T]

Anything else??? 💩💩💩👎👎. Should b thankful no complaining like a baby

[@liveforever6466]

Ppppoppppppppppppppppppppppppp u pppppoppooppoopppooppooppooppppoopppooppoopppoppoppooppooppoopppoppoopppooppoppoopppooppooppoopppoopppoopooppoppooppooppooppoppopppooppooppoppooppooppooppooppoppooppooppooppoppooppppoppooppooppoopppooppooppooppooppoopppppooppoopp0ppoppp0ppoppoopp

[@dzerres]

Orbit customer service blows. Called them two times each time ending up in Belize where the persons HAD NEVER EVEN SEEN AN ORBIT VALVE (I'm asking about the "bleed" button - it leaks or cuts off the water flow - no in between). I have 17 of these valves and they are always failing - usually the anti-siphon part. Orbit doesn't care and so neither do I any longer - Gonna check into other manufacturers available at HD or Lowe's. I also have Flume water detection system - it just will not connect to my internet system since I switched to a "mesh" network. What a waste of time and money! Don't do it. I have 4 control clocks and they keep failing too - usually the LED screen fades out to where you can't read it. Orbit is a Utah company - so buyer beware - that whole state is a scam (I lived there and I don't trust 'em).

[@salsevere5646]

The music is totally annoying. Otherwise, great info.

[@MIND9988T]

🙏👍🙏👍🙏

[@SpencerG82]

Nice meme

[@chuckgioia6436]

B

[@byronlastrapes6979]

ew