Jeep Grand Cherokee WK2 Headlight Bulb Replacement | 2011-2021

This week we are back to working on the 2018 Jeep Grand Cherokee WK2. Today I will be showing you how to replace the factory halogen bulbs. This process may be very similar across other Jeep vehicles. If you have any questions or comments please post below. Make sure to like and subscribe for more how-to content!
OutJeeping Merch Store: outjeeping.com
Andeman Jump Starter couple code 10% Off: 10OutJeep
Andeman Jump Starter: www.amazon.com/dp/B09N37C4LG?...
Music Credit:
Garage by Topher Mohr and Alex Elena
Pickup Truck by Silent Partner

[@cosmocrisanti3568]

Thank you for the video. I followed the instructions in other tutorials but found it impossible to remove the passenger headlight from the top. Removing the bumper was going to be my next attempt at replacing the headlight. This method made the job a lot easier.

[@HeavyHaul51]

I have a 2015 Grand Cherokee limited. Replaced the Drivers side High and Low Beams. It was a real pain in the ass but way easier then the passenger side is turning out to be. The high beam was a piece of cake. I have access to the low beam but can't get the bulb to turn to remove. Top bottom no good it's like someone jammed it in there and put the cap back on and said the hell with it . Iv tried prying on it twisting it but the bulb won't budge. Bad angle and no room. I moved the ecm still can't get to the bulb. I'm guessing the bumper needs to come off now and remove the whole light unit. My hands look like they went through a meat grinder. Any Ideas

[@timothylowe2073]

If you go in from the top. Unclip the ecu and move to the side and you have full access to the bulb housing

[@jcolefan2]

I went in from the top, but can only touch the clip with my one finger. There's no way I can apply enough force to turn it counterclockwise. Any suggestions or tips will be greatly appreciated!

[@cosmocrisanti3568]

@@jcolefan2 I went from the bottom as shown in the video. The burned out bulb came out easily because whoever changed it last didn't tighten it properly back into place. In putting a new bulb back into the socket I was able to slide the open end of a 21 mm wrench over the connector/bulb for some added torque. You may want to give it a shot by doing the same thing to loosen it. Good luck.

[@ibowhuntga]

@@jcolefan2 As your comment is 2 weeks old now, it may be too late for you., but there is a 2021 shorts video from someone who made a tool out of PVC pipe to give you something to grip the bulb with. His video description is "Grand Cherokee Laredo headlight bulb tool". I have not tried it, but as I am here looking at videos, you know I am going to be swapping bulbs tomorrow. It looks like a handy, cheap tool to make.

[@michelantoniomorin2201]

👍👍

[@SassyGiraffe7]

This was a great video. I wish I saw this one, too, with the others I've watched. BIIIIG PROBLEM!! My bulb is ridiculously stuck. I couldn't figure out the angle to pull the bulb out and ended up breaking it. I dont know if there's still a piece of the bulb inside the housing. I can't get the new one in there and I dont know where the rest fell. It didn't land on the ground. When I tried to put the new bulb in, I couldnt get it to latch, then I dropped that bulb. 🤦🏽‍♀️🙄 It fell into the same abyss of the first one and I can't find that one, either. Is there a way to share my photos of my housing? I dont know what else to do.

[@OutJeeping]

You can message me via Instagram or email me. You might just need to remove the whole headlight housing to put them in properly.

[@mikea3552]

At 5:19, would you happen to know the link to buy those Mopar plastic covers or know the Mopar item number to order? Mine is gone too

[@OutJeeping]

Mopar part number is 68354272AA. I got mine from the dealer.

[@mikea3552]

You da man! thank you very much! @@OutJeeping

[@miniemouse2750]

Hola vivo en Ecuador y tengo un jeep cherokee 4.0 6l automático de 1987 necesito comprar un sensor de oxígeno, pero amazon y autozone venden diferentes, ¿dónde puedo conseguir repuestos que sean garantizados y no tenga que estar devolviendo

[@OutJeeping]

I would try Rockauto.com if they are able to ship to you.

[@haydenwinfrey1337]

What happened to the xj build

[@OutJeeping]

It's still in progress, just waiting on partd to arrive.

[@mamatidea]

When the bulb burns out buy new car. This is not a serviceable assembly.

[@OutJeeping]

😄

[@SassyGiraffe7]

😂😂

[@Jpizzel22]

I don’t know how tf to get the bulb out…I can see the MF but it’s untenable unless you have the hands of an 8year old