Carb Cleaning 25cc Blower

Cleaned the Carburetor on the 25cc Craftsman Leaf Blower.
If you are interested in seeing or purchasing items I use, click the link below:
USA www.amazon.com/shop/paisteboy
CAN www.amazon.ca/shop/paisteboy
As an Amazon Associate, I earn from qualifying purchases. This helps support the channel and allows me to continue to make videos like this. Thank you!
Follow PAISTEBOY on Instagram:
Like PAISTEBOY on Facebook:
paisteboy?re...

[@RhythmChair]

Helpful video... my leaf blower was doing the same as yours... cleaned the carburetor and replaced the air filter, but took it one step further... I replaced the 2 fuel lines and cleaned the gas filter. People sometimes don’t realize these blowers have a filter inside the gas tank. Once I did all that the blower run like new again.

[@donfrench5978]

My similar model Poulan had a starting/running problem; would barely run. I tried cleaning/adjusting the carb using the $10 tool from Amazon, replaced the spark plug, squirted Seafoam DeepCreep into the air intake but it still would barely run, albeit better than before. Then removed the 2 screws that hold on the plastic cover over the muffler, then removed the 2 screws that hold on the muffler discharge plate, then cleaned the carbon out of the 4 tiny discharge holes in the plate that were partially plugged with carbon. It then started right up and now runs like a champ! If the tiny holes get plugged with carbon the blower either wont start or wont run well.

[@nachoby81]

Excellent video, very helpful thanks

[@joekorpiewski2573]

Thanks for the help. I will be working on my carb soon.

[@JS-kd6yz]

Hey Pasteboy, were you able to buy a tool to adjust the poulan carburetor? Did you find out if it was the diagram or just adjusting the carb to go full throttle?

[@MrRedneckrc]

Another great video. Any end of the season garden videos planed. Keep up the good work.

[@ohyeah3750]

That's just what mine did. Adjust the needles first. High speed is to lean. Also had to replace the fuel tubing. Major job on that one.

[@markhulbert620]

Here's a helpful "MacGyver" trick I learned from another video, that you can use when you don't have the special adjustment tool. Take the plastic applicator tube off of something like a tube of silicon or glue, heat up the end and place it over the adjustment screw. It should form to the screw and hopefully give you enough torque to turn it.

[@asappestcontrol1250]

Thanks. Forgot which hose went where and you helped me out. Just ordered a new carb via Amazon $21

[@Vdubin64bug]

I have the same blower (I also have a few videos up on it) I've owned mine since 2001 and let me tell you... It's been a lot of maintenance lately.. I've always ran good quality oils as well.. I will most likely keep my old Craftsman blower, even though it's been a headache at times.. But, I finally sucked it up, and spent the money, on a really nice high quality handheld blower.. Figure, I'll use it when I'm in need, and need one that's dependable.. I have way too much money into my Craftsman blower, to do anything with it but keep it.. (You'll see if you watch my videos) I purchased a Stihl Bg 86... I haven't even unboxed it yet.. Great video !

[@mwpinnc1]

Clear. Thanks.

[@slawomirduda9248]

Thank You.

[@alex.joe.my.way8966]

Dude your the man thanks so much

[@codyvincent4699]

Use a dremel and cut slots in them to use a flat screw driver, high idle screw needs adjusted out

[@davidadamus177]

Thanks for the video, got my carb cleaned really easily. Is it normal that when I took the large hose off the carb no gas dripped out?

[@charlesoverton]

I love it... thanks

[@thomaswhetzell7485]

Hello awesome video I have the same one that I just got from garage

[@johnmott5382]

What does it mean if I have to continue to adjust the fuel mixture screws on a carburetor?

[@bradthompson9758]

Thanks for posting! Had my fuel lines hooked up wrong and the primer / purge bulb wasn't pulling any fuel through the lines - whoops!

[@robertlaird3929]

Hi Paisteboy I was wondering if you ever found the problem with that craftsman leaf blower and how it only ran good on half choke I am having the same problem with the same blower.thanks