Panic Mode Day 44

SUBSCRIBE AND GET NOTIFICATIONS!
kzbin.info...
CHECK OUT THESE PLAYLISTS OF REPAIR SERIES AND OTHER FUN STUFF!
(To go to the Playlist Menu page, Click here: )
kzbin.info...
1969 Dodge D300 Power Steering Retrofit Install
• 1969 Dodge D 300 Power...
Bringing It Back To Life: 1968 F 250 Camper Special
• Bringing It Back To Li...
1958 GMC Resurrection
• 58 GMC Resurrection Pa...
1941 Dodge WC6 Command Car Entire Series
• 1 of 15 1941 Dodge Pow...
Master Craft Mower Resurrection
• Mastercraft Mower Resu...
1957 Chevy 5400 Low Cab Forward Rescue
• Pt 1, 1957 Chevy 5400 ...
Snow Smashed Shop Recovery
• Snow Smashed Shop Reco...
Operation Crusty Truck
• Operation Crusty Truck...
2014 Hayfield Follies!
• Hayfield Follies Part 1
1985 Dodge One Ton 4x4
• 1985 Dodge One Ton 4x4...
Meyer E 47 Snow Plow Installation
• Part 1/6 1969 GMC 4x4 ...
The 1968 GMC Water Truck Adventures
• Part 1 Air Heater Expe...
1946 ACF Brill
• 1948 ACF BRILL 35 foot...
1975 Chevy Half Ton
• 1 of 3 75 Chevy half ton
1985 Chevy Silverado Half ton
• Redneck Restoration's ...
1959 Pontiac 389 resurrection for "The Find" 1956 GMC
• Part1 1959 Pontiac 389...
IHC 300 Utility Camshaft Repair
• Part1 International 30...

[@ellesmerewildwood4858]

All those hens shouting at each other, even the rooster couldn't get a word in.

[@martinbalmforth2665]

Reminds me of drunk women outside a nightclub

[@martinbalmforth2665]

How is Tony doing?

[@xcop4511]

I never get tired of watching Jeff do stuff... xCop

[@bensteward2288]

OUTSTANDING MECHANICAL ABILITY!

[@cliffhaupt5413]

Bending tube isn’t easy. Good job Jeff.

[@DanEBoyd]

I'm starting to get nervous!

[@rdsledge]

Love the sounds of the chickens in the background and the dog barking however, I do miss goats.

[@960wattoffgridrv]

the only thing making me panic is that it's the middle of April and I'm still shovelling snow again to find a little hint of springtime!

[@macgvrs]

Don't have a tubing bender. Can definitely see why one would be useful, though I wouldn't need it much. I guess that's why I don't have one. That and the fact that I just bend things by hand, using a larger radius to prevent kinking. Looks a lot nicer though if you have the tool. Great work. All these little jobs just take up so much time.

[@Kickinpony66]

@2:53... I think I suffered a slight fracture in my fingers once, from my carbide-tipped hole saw grabbing into an aluminum pole (yes I was running it "Full Tilt Boogie"!). I vowed: Never Again. It is nice to have an enine for Mocking Up parts and pieces, like the fuel line.

[@bitsnpieces77]

Nice job on the line looks great 👍

[@donley8416]

Jeff great work you will get it finished in time

[@rodmacisaac5963]

Thanks Jeff! 👍😎

[@MrJim0823]

Thanks Jeff

[@kriswright1022]

Any updates on the old Dutchman?

[@Gordonseries385]

👍 Cool 🐓

[@Reaglesracing44_]

jeff what ever happened with the ole water truck and the 67 pickup you replaced the closed knuckle front axle shaft in??

[@ElderlyIron]

All here, but the 69 is still closed knuckle.

[@Reaglesracing44_]

@@ElderlyIron i remember watching the ACF Brill Series

[@DAVIDBrown-zp8sz]

BIG MISSTAKE I THINK ! Lower hose too short, it's supposed to be long enough to be flexible to let engine rock from torque and not strain fuel tubing.

[@ElderlyIron]

It's vacuum line for the booster, of which the line at the frame is also suspended by hose at the other end, and not rigidly attached to the frame. Engine is a 4 point mount. 2 at the bell housing and 2 below the damper. Engine movement is minimal.

[@cemx86]

A metric moment - Our host is dividing 1-3/4 inches he estimated with a tape measure. He says "So half of 1-3/4 is half of 1 plus half of 3/4 which is 1/2 plus 3/8 which is 7/8. True but let's try that in metric. 1-3/4" is 44mm. Hmmm, what is half of 44? Anyone? Bueler?

[@Jimschrbr]

That would be all well and good, except here in these United States of America we REFUSE to use the metric system. Besides, when all your rulers and measuring devices are in inches how are you going to figure how long 22mm is? 😳

[@cemx86]

@@Jimschrbr Funny. 😄 Heck, guys, everything we buy these days it seems can be taken apart with a 10mm wrench. Even our money is metric (do you want 120 cents to the dollar?). The HW store's parts aisle is fast becoming half SAE and half metric. As an AMERICAN I use metric when measuring lots of things. I didn't use to. But it is just plain-jane much simpler. I have swayed some "no metric here" kind of guys by asking "What is half of 3-15/16 inches?" [insert blank look here] "OK, then what is half of 100mm?". [insert lightbulb over head here] OK, I know that this is an example that works out to my advantage. But it gets the idea across. I get it that construction items (electrical, plumbing, lumber) will remain non-metric for quite a while. But not much else is. How about just giving it a try?