Panic Mode Day 43

SUBSCRIBE AND GET NOTIFICATIONS!
www.youtube.co...
CHECK OUT THESE PLAYLISTS OF REPAIR SERIES AND OTHER FUN STUFF!
(To go to the Playlist Menu page, Click here: )
www.youtube.co...
1969 Dodge D300 Power Steering Retrofit Install
• 1969 Dodge D 300 Power...
Bringing It Back To Life: 1968 F 250 Camper Special
• Bringing It Back To Li...
1958 GMC Resurrection
• 58 GMC Resurrection Pa...
1941 Dodge WC6 Command Car Entire Series
• 1 of 15 1941 Dodge Pow...
Master Craft Mower Resurrection
• Mastercraft Mower Resu...
1957 Chevy 5400 Low Cab Forward Rescue
• Pt 1, 1957 Chevy 5400 ...
Snow Smashed Shop Recovery
• Snow Smashed Shop Reco...
Operation Crusty Truck
• Operation Crusty Truck...
2014 Hayfield Follies!
• Hayfield Follies Part 1
1985 Dodge One Ton 4x4
• 1985 Dodge One Ton 4x4...
Meyer E 47 Snow Plow Installation
• Part 1/6 1969 GMC 4x4 ...
The 1968 GMC Water Truck Adventures
• Part 1 Air Heater Expe...
1946 ACF Brill
• 1948 ACF BRILL 35 foot...
1975 Chevy Half Ton
• 1 of 3 75 Chevy half ton
1985 Chevy Silverado Half ton
• Redneck Restoration's ...
1959 Pontiac 389 resurrection for "The Find" 1956 GMC
• Part1 1959 Pontiac 389...
IHC 300 Utility Camshaft Repair
• Part1 International 30...

[@RandySchartiger]

yessir! not a day goes by I have to fix something! just to keep this place going! lol fix it and save a small fortune, all the fixes combined does save a lot of money! thanks for the mention brother!

[@xcop4511]

I never get tired of watching Jeff do stuff... xCop

[@jamesthompson8008]

"What's better than OEM?"....in this case perhaps NOS OEM? ...I know, I know, enough. Hope Tony improving best he can.

[@darrinfry2251]

What I am waiting to see !! Is when you test drive this in the woods 👍

[@MrJim0823]

Thanks Jeff

[@rodmacisaac5963]

Thanks Jeff👍😎

[@daleolson3506]

Just Tony not smoking will help him

[@jimmyfiggs6293]

That's the Exact Procedure the factory used to install it

[@glenharper3136]

Thanks for the video.

[@rdsledge]

Twist the “L” bracket? You mean adjust the “L” bracket!

[@dfross87]

With a Precision Adjustment Device, no less.

[@johnboutchia2349]

Hope Tony is better, if you bought new cables you would save all that time messing around with them to spend on getting other things done, some of the things on my truck were beyond saving

[@martinbalmforth2665]

Hope Tony is improving. My father in law has just been hospitalised with the same today. It is not looking good for him as cancer has left him so frail

[@DanEBoyd]

I didn't identify the 'Stainless song,' but I think I hear Please Release Me segueing into Rubber Band Man. I would've squirted some solvent through those cable sheaths.

[@ElderlyIron]

"Shameless" Garth Brooks

[@Lazarus1940]

I'm curious if you've ever considered using a capped pipe for soaking cables and other long skinny things. You could fill it with your muriatic acid and stand it against a post while gravity helped the contaminants fall away. Just a thought.

[@ElderlyIron]

No, I hadn't, but I'll be doing it from now on!

[@burlatsdemontaigne6147]

#43 covered all the bases.

[@Kickinpony66]

My goodness, I've never seen a heater control without broken levers!

[@RobertPerrigoOkiechopper]

Jeff, is this project for someone else? I really like your attention to the smallest detail .