PART#2 2017 Chevy Suburban Power Steering Assist Drive With Care, Replace Motor from Another Unit

[@الحمدللهعلىكلحال-م7ص]

Did not show when unpin the connector. Thank you so much for your helpful video

[@lhen_2288]

Dito lang sir watching.

[@tommylawrence9601]

What’s the purpose of the plastic cover?

[@lsxg8398]

Replaced the power steering motor on mine and turns full left by itself when parked

[@KenKejAutoElecTrix]

Try to relearn

[@lsxg8398]

@@KenKejAutoElecTrix how do I do that

[@KenKejAutoElecTrix]

@lsxg8398 perform relearn by diagnostic tools, if the problem not exists perform online programming through TLC techline connect

[@أبوعبدالله_العاصمي]

You are artistic.

[@gaigefox3112]

When tightening the bolts for the motor, how much tension should I put on the motor against the belt

[@kennethcamilotes7694]

TAMSAK DONE BOSS KENKEJ👍👍👍👍

[@cameronwohlgemuth5901]

Can you please send the link for the instructions?

[@sawyerrmcgee]

Yes need instructions!

[@tommylawrence9601]

Ok so I replaced my Power Steering Assist Motor as the video said but once I start it up and get it the wheel doesn’t turn at all now where before it turned some. Could I have put something back wrong or clocked it wrong? Send it to the dealership they said they programmed it but it still isn’t turning. HELP PLEASE

[@KenKejAutoElecTrix]

Send it back again to dealership to fixed that problem. That is electrical issues.

[@tommylawrence9601]

Ok as in the cables or the motor itself?

[@KenKejAutoElecTrix]

Please check main fuse on the battery side.

[@tommylawrence9601]

Anything else I should check? I think my tabs broke on the harness that connects to the motor but they still plug in could that be the issue?

[@tommylawrence9601]

Indeed it was the harness that powers the EPS motor once code were deleted it started working. But know has a loud whining almost grinding noise coming from the rack any suggestions of what it may be?

[@mechanicrepair06]

good am po ,pasensya po sa abala ulit,pahingi po ulit ng tulong,kasi may ginagawa po ako na silverado 2017 matigas ang steering nya.at no communication din po,pwed po ba isang second hand na steering para hindi na mag program ako.salamat poulit sa sagot nyo.

[@KenKejAutoElecTrix]

Pag bumili ng 2ndhand complete kasama rock end pinion at torque sensor. Lahat ng kinakabitan ng motor para wlang ng programming

[@mechanicrepair06]

ok salamt po sa sagot nyo,salamat ulit sa walang humpay sa mga sagot nyo sa humihingi ng tulong,thanks@@KenKejAutoElecTrix

[@ZafarIqbal-xg2ki]

I s to know my GMC yukon 2017 Why move steering rack right side automatic but left side little bit hard working because motor move automatically right side but left side when I move steering wheel left side little bit hard why how can I resolve this problem

[@KenKejAutoElecTrix]

Need to be relearned using Techline Connect, Go to your nearest GM showroom.

[@ZafarIqbal-xg2ki]

Thanks brother

[@pinoyelectressyan2806]

Next episode

[@user-gp6kw2xx6w]

I have 15 sierra C0475-64 : power steering motor circuit - slip detected - current . C0800-03 : control module power circuit - low voltage - history. Any thoughts ?

[@KenKejAutoElecTrix]

The power steering control module monitor for a motor signal mismatch and excessive rack travel

[@KenKejAutoElecTrix]

Check drive belt of steering motor inside of the steering gear.

[@user-gp6kw2xx6w]

Yes it’s the belts cut into three pieces Thank you for ur help 🤗

[@user-gp6kw2xx6w]

Do you have p/n of the belts & where can i find it, cuz the dealer said i have to buy the whole p/s.

[@KenKejAutoElecTrix]

I got part number from the google type this PSS.EPS.GMC.002

[@gaigefox3112]

I changed my motor but its makes a noise where I turn hard left or right at a stand still. what could that be?

[@KenKejAutoElecTrix]

Need relearn

[@gaigefox3112]

Ok ill try that, thank you

[@gaigefox3112]

Can I send you a video for your advice? I am trying to figure out if its my whole rack or i did something wrong when I installed it

[@tommylawrence9601]

Do you a have a video of this I took mines to the dealer they said they programmed it and it still will not turn any but backs a noise when I try to turn the wheel but it doesnt turn any. Could I have put something back together wrong?

[@betobeitia637]

tengo ese problema, como lo soluciono

[@boybravo689]

Master tama ba ako ni lelearn mo lng mo lng ang computer tapos denelete mo ung current code nag scan ka ulit nawala na yong dating dtc master pagkatapos mong magpalit ng power steering motor tnx sa susunod mag video ka naman kng paano gumamit ng scanner

[@KenKejAutoElecTrix]

Relearn at delete DTC lang sir, pero itong sa video na ito nagtry akong magrelearn at delete pro hindi sya makuha, hindi nawawala ang display aa cluster panel na steering assist drive with care, pero lumambot ang steering nung pagkatpos mo magrelearn. Ang huling option ko pinalitan ko ng bagong EPS Electronic power steering at program via online

[@boybravo689]

@@KenKejAutoElecTrix master pag may time ka next time magvideo ka kng paano gumamit ng scanner tnx