Peak Atlas ESR70 Repair

[@PeakAtlas]

You have done a very nice quality repair. Delighted to see that the calibration process worked well for you too.

[@MrKardacz]

Hello; I have to calibrate my ATLAS PEAK LCR40; can you tell me the procedure to follow ???? Thank you very much in advance

[@MrKardacz]

Hello; can you tell me what the different values of resistors for calibration of the ATLAS PEAK LCR40 ???? I did some research, and I found nothing

[@johncunningham5435]

Excellent presentation on how to correctly repair a device of this caliber. I also own the identical model and it is worth every penny, more than paid for itself in troubleshooting time and energy.

[@jameshorn7830]

Nice job on the surface mount soldering. You make it look easy...

[@PyroShim]

A very professional repair. Great job.

[@luisvilleza2687]

Nice video i hope you can upload more in the future i see that you replaced some components that have burn marks and pin hole thank you for sharing

[@elderman638]

Hello. Can you inform me about the calibration resistor values ? This calibration method is used when PIC is changed ? Thank you.

[@dav1dbone]

There's a time delay before it tests, could they not have built in a protection circuit, where if there's any potential between the input wires the input is switched to a discharge resistor?

[@douro20]

I wonder how much the tips are for that JBC station compared to the Hakko or Weller integral tips; I would imagine they are significantly more expensive.

[@eeeeetfish]

I have one that needs repair - is this something you could do ?

[@tonyd1149]

You're an artist. Thank you for making and posting this video. ¿Does a new meter (as this) come with calibrating resistors as you have shown here? Are the low resistance measurements stable & repeatable? Thank you.

[@whoisme678]

Old Post, but a very nice job. I cant see what you repaired as to simply desoldered and then resoldered the same items?

[@etienneguyot9069]

Great repair of this classical mistake... Could you give more details about the calibration steps? How you activate this menu? What are the resistor values? (I need to perform this step on my own ESR70 as I've a small permanent CC offset, even with the customer auto-calibration procedure)

[@texasguitarslim]

My ESR70 stopped automaticly measuring components. I have to push the test button again, while trying to hold components in my hand, which is very stupid. What kind of problem IS THIS? Thanks for Everything.

[@riaanleroux5972]

hi i have same problem can u tell me what is the letters is before the 4903 on the regulator ic i have try to check but no luck or any equivalent replacement part please i want to fix it .thanks for a great video

[@danielsahagun4367]

Sir: You made my day, nice job and thanks for teaching me. Please I have a question: How many wats is your soldering iron? Thanks in advance for your answer

[@Filip.Honzarek]

Hi, I'm using JBC T245 handle with 50W power I think...

[@grigoreman7198]

Great. Thank you!

[@ferndog1461]

Pretty good work. Thank you.

[@rebosallos]

Técnica impecable.

[@Kennynva]

What kind of liquid flux do you use and where do you get it...??? Thanks..

[@boulder89984]

Not sure about the repair thing, but a great soldering video!

[@discomovilPROMUSIC]

It is assumed that the tester is relatively new, which had lifetime? regards

[@sstenks]

Very nice work thanks for share video.

[@geraldbrown8286]

What is that protective tape ?

[@Filip.Honzarek]

Capton tape

[@lynyx77]

I've the same Model ESR70 and I've never seen this menu about calibration, is it because you change the Pic and it's his first time starting? Can you tell me more about this procedure with resistor? Thanks and great video and nice work.

[@SporkSchivago]

Do you know if you can use a hotgun on BGA components? Or do you need something special for that? Thanks again!

[@Filip.Honzarek]

For BGA components you need special device named "BGA Infrared Rework Station". Just search on google. Also you need balls, etc...

[@SporkSchivago]

{78b39062af45ec} Thank you. No way to do BGA with a hot air gun?

[@Filip.Honzarek]

***** i think hot gun is for classic smd components and IC's with legs.

[@saarike]

I have nothing more to say, but nice repair!

[@ChiyouPWu]

Hey forgot mention part number and location of each components?

[@f.m.a5928]

What kind of tool you have used to grab ic while desoldering?

[@Filip.Honzarek]

www.google.com/search?q=pean&num=20&tbm=isch

[@cncit]

Nice work..what temp do you have the iron set at for re soldering?

[@Filip.Honzarek]

It depends on iron. I use sn60pb40, 335 temp. in degrees.

[@SporkSchivago]

Could you please tell me what equipment you are using to do this repair? For example, what soldering iron are you using? Are you using a heat gun or what? Also, what brand of desoldering braid do you use? Why type of flux are you using? Is it no-clean flux? I always have a pain in the butt time trying to desolder SMD components using my current radio shack digital desoldering station. Thank you so much for such a wonderful video. You did a real good job.

[@Filip.Honzarek]

I use cheap heat-gun ATTEN 858D, soldering iron is Sn63Pb37 MTL468. Brand is Chemtronics. Flux is MTL468 mixed with IPA. MTL468 is no-clean flux. Soldering and desoldering station is expensive JBC model (jbctools.com). For desoldering multipin components i use heat-gun - it's easy and fast. Thank you.

[@SporkSchivago]

{78b39062af45ec} Thank you for the response. I just bought some Weller WHA900 heat gun / rework station thing. Hopefully, it's at least equivalent to your ATTEN 858D. I've been working on electronics for a while now, using just a soldering iron, and as SMD components get smaller and smaller, I've decided it was finally time to buy something a little more suited to my needs. Thanks for the video.

[@atmelmetall7500]

Thanks for the answer.

[@grigoreman7198]

Where you found the software for PIC16F886?

[@Filip.Honzarek]

+Grigore Man Peak sent programmed chip to me for free. Great service.

[@discoHR]

Nicely done. What temperature were you using on the hot air gun? Desoldering was very quick.

[@Filip.Honzarek]

i don't remember, i think 350-390 `C

[@filiperodrigues1816]

best work!

[@atmelmetall7500]

how much to pay for a new PIC?

[@Filip.Honzarek]

+Atmel Metall Peak sent me for free. Great service.

[@MrKardacz]

Hello; can you tell me what the different values of resistors for calibration of the ATLAS PEAK LCR40 ???? I did some research, and I found nothing

[@alessandrovastola8559]

gg

[@ZilogBob]

So much for its "It discharges all charged capacitors automatically" claim.

[@duronboy2]

50v or under, although I've seen it survive higher. But OP said it was a high-voltage cap, so I'm assuming well over 50v.

[@atmelmetall7500]

this is alternative device (open proect on atmega8) vrtp.ru/index.php?showtopic=21281&st=0 I recommended for copy

[@michelbuet2236]

Use translate.google

[@luismardones2554]

Bad remove extraction SMD TECHNIQUE. Aluminium or copper laminate is better, and cutter pins in cold smd chip is top.