Pioneering My Alaska | Part 2.2 | Epic Bridge

The Continuation of a crazy Fall trip to the land I soon will call my home.
To those who commented ideas in Part 2.1 for supporting the middle of the bridge, I appreciate your input. Please be aware that with the creek being a salmon spawning ground, I can not put any permanent structure or drastically change the flow of water legally. (The reason for the cable idea) If you have any ideas that don't involve putting anything in the water I would love to hear them.
To those that commented in Part 2.1 about the low end of the bridge needing to be further away from the creek bank and higher above the water level. I hear you and I agree. My next trip to the property will include fixing this issue. I appreciate your bringing it to my attention
I am sorry to announce this, but I won't be back to AK until next summer. Please remember this is just the very very beginnings of a complete 180° life change. This winter will be spent down in Arizona where I currently live and work. But that does not mean I have quit on my dream and that doesn't mean I will stop documenting my journey. When the snow melts next spring, I will be back in Alaska working away yet again. Soon enough this channel will be putting out weekly episodes and I will be living there full time. But for now, patience will be a virtue.
Thanks again to all you lovely people that support this channel. I appreciate your likes, shares, subscriptions, and comments. Someday, this KZbin channel may be the only source of income I have.
Sincerely,
Ty (Life on Fish Creek)
I own the licensing rights to;
Intro:
Elijah Siegler- Alaskan Heart
Drone/Timelapse music:
Hans Zimmer- Mount Fuji
#alaska #homestead #nature #offgrid #remotework #mountains #construction #alone #asmr #solo

[@altaylor951]

Great job on the bridge! One thing I would highly recommend, is to get some heavy chain, and tie the bridge off to something immovable, on both ends, or the spring run off, and ice will happily relocate the bridge for you, as I learned the hard way. Keep up the great work! Cheers!

[@The27kart]

Attach a cable 10 or 15 feet up each of two trees, them run the other ends down to the middle of the bridge on each side. Use turnbuckles to pull up on the bridge to take the flex out of it. Running an X under it won't be worth the time or energy. Also, try to raise the lower end, high water, debris or ice jam is going to take it out. Good luck! Stay safe!

[@LifeonFishCreek]

@@The27kart I like this idea, I'm a little worried about leverage, as in the weight of the bridge pulling down at such a high point on the tree. The reason for the x cables would be to keep the stress on the trees at the very bottom and strongest part of the tree. What do you think about this worry I have?

[@mikecrawford7352]

I would attach the cable 10 to 15 feet up. But take a cable down the back side as close to being in line as possible to a stump of a tree to take the pressure of pulling the trees inward and the stress would be transferred to straight down the trees. Raising the lower end on cribbing stacking logs up just a few feet would be beneficial than a small bridge to the top of the bank. If you were further off the water a cable attached to both ends of the logs and a vertical 2 feet in length or so underneath between the cable and the logs. Once you tighten the cable it would arch them up them and you could nail them together. You would need sufficient spacing from the creek to the bottom of the vertical. The longer the vertical the more of an arch, however wood only flexes so far so you wouldn’t want to get to carried away.

[@LifeonFishCreek]

@@mikecrawford7352 love this, thank you!

[@mikecrawford7352]

@@LifeonFishCreekanother idea occurred to me, back in the day they moved heavy logs by building an A frame out of 8’ logs or thereabouts and you have a rope tied to the log you want to move that runs a few feet to the top of the a frame. You then prop it up and pull on a long rope lifting the log up. As the a frame gets to the vertical point gravity takes over and the log is dragged by its own weight around 6’. Obviously this can be achieved using a come along. The taller the A frame the further the log moves but the more effort is needed. You could also use a pulley at the top of the A frame and down to the log you want to move.

[@LifeonFishCreek]

@@mikecrawford7352 Genius, I've seen this done before but I've never tried it. I'll give it a shot on that second bridge next summer

[@williamsimmons8927]

Determination accomplishes the impossible, the idea of using from above cables for the support for the timbers is righteous, with out a way of anchoring the structure the spring thaw may make your bridge a huge raft,you got spit young man no one can take that away from you for sure , im hooked.

[@phillipstubbington7555]

Great effort mate, just goes to show what can be achieved with focus and perseverance...very well done!!

[@rogercarter8649]

Build a Crib in the center, put in a couple of post , and a beam to underside of logs, fill crib with rocks from river bed

[@neutonrenda2303]

Epic build, you didn't play around. I really am looking forward to seeing how your journey goes and I'll be looking forward to anything you post in future. Safe travels home and take care.👍

[@Cloudface77]

Enjoying watching your videos. Keep going, you'll break through.

[@sunnyrivers]

Holy Wowsa! That bridge is a remarkable accomplishment! Your tenacity is admirable and I look forward to what’s next. The cable idea sounds like a clever solution 😊 Hope your hand is healing well too!

[@colinflenley1203]

Another great video. Spacing the logs will lighten the weight as well

[@skeetermalcolm1655]

You were right about the bridge brother it's epic, love the channel and looking forward to seeing the next one

[@VikkiBernson]

Great video as is your bridge. And your property location is beautiful. Peace ✌️

[@resbum2554]

Awesome accomplishment. Subscribed. You seem open to constructive input. You have trees at three corners for suspension cables. In that country you should be able to dig deep enough to sink an upright post(tree) at the fourth corner. You said the road bed is nine feet wide. Place a 16 foot beam(tree) centered under the middle of the bridge. Attaching the suspension cables to the ends of that would give you a straight line pull between the trees (and post) on either bank. The trees and post should only be used to establish the high points for the cable, which should continue past them anchored into the ground. Again, awesome solo accomplishment. I'm looking forward to next summer's vids.

[@wendyshick6689]

I am excited to see your channel grow I love your content Alaska is beautiful country a good job on the bridge and by the way I didn't look away😊 I hope we don't have to wait too long to see an upcoming video😊👍🐟🐟🐟🐟🐟🐟🐟

[@LifeonFishCreek]

@@wendyshick6689 Thanks Wendy, I will try to post occasionally while here in Arizona. Maybe a day in the life video? Or a shooting range video? Any adventures i go on here I will film and post as well. I appreciate your support since the beginning.

[@GuillotineStare]

I was happy to get this video. After the last one, I wasn't expecting another upload for months.I guess NOW, that will be the case. Looking forward to your return!

[@LifeonFishCreek]

😭 will be a long time before I can return, Long winter's.

[@Buzz420]

You have enough advice here so I will congratulate you on the bridge work & leave you with a reminder. When cutting kindling with an axe, use a small stick to hold the piece your going to swing your axe at. Better to chop a stick than your hand or finger. You're doing great, keep it up & be careful

[@edwardroxas1574]

Diagonal cable lines on trees to center of bridge to lift the center of bridge.

[@a.m.k6143]

Wow, that was one epic bridge build. Look forward to the completion next year.

[@jonr473]

Amazing content, super effort on the bridge build 💪👍

[@neutonrenda2303]

What an amazing achievement, I'm floored by what you've done alone. All of that is definitely going to be a great learning curve and help with the future. Sorry to see the injury, it happens and normally it's going to be in a place that reminds you every time you need to do something. Hopefully it won't take long to heal without too much problems.👍❤️

[@LifeonFishCreek]

@@neutonrenda2303 Thank you thank you. My hand is nearly healed up already. 👍🏼

[@nickrubberboot3673]

Fantastic LaCrosse waders!! Great job!!

[@LifeonFishCreek]

@@nickrubberboot3673 5 star review for sure!

[@greggssausageroll6445]

Hey kiddo, Like the vids but please consider using safety glass when chopping fire wood, Had a mate lost an eye last year doing the exact same thing, Shit happens bud !! Take care X from France

[@donvance195]

thanks for the great post. I have been looking for your new movie ever since early summer when you built the a frame. Looks like the spacing of the logs worked well and improved your weight worries at the center of the span. I suppose a 20 inch rubber tire or atv tracks will crawl over that easily. Hope you hand feels better. I bet that was a lot of aches to drive 100+ spikes. Looking forward to new content. It will be fun to see winter there if you ever are able to go year round.

[@northidahodreaming5657]

great video....keep it up thanks

[@torbenlarsen298]

Great video, good job on the bridge! 🤠

[@ervintaylor6508]

Love this channel man I have a suggestion though if you keep using your axe as a hammer it's not going to last you very long out in the bush the poll of the axe is not hardened on most, if it is on yours that's awesome but most aren't you need to get a dedicated 2 lb sledge Hammer for that kind of stuff.

[@LifeonFishCreek]

Thanks for the tip

[@richuhl849]

Great job but you need to take safety seriously, use proper tools, and safety gear. You are in the wild,who,s going to help you.

[@Nena84734]

It sure was nice to see your plan come together, what a ton of work though! It is, after all, the most important jobs you will have cutting the trail to your property, access any time of year.

[@mikeplatts2603]

Hell of an effort, well done.

[@nancybrown2700]

Your Buck 110 is a awesome camp kniofe but also get a good fixed blade bush craft knife to baton your wood for kindling. That way you hands are never in striking range and the axe and you can do the splitting work with little hazard. It is great to view your progress but injuries like that your your hand can be avoided. Stay safe. Love you videos.

[@TarquinTheTall]

Would be interesting if you are leaving for the winter to have a camera on a tree near the bridge so you can see how it holds up. You're absolutely mad building it....but I'm sure you know that. 😂 Loving this journey.

[@LifeonFishCreek]

I have a camera up there but the battery is not charging for it. So it will be useless this winter.

[@janosszabo98]

I read the description under the video, so I know you're aware the issue with it being so low. I'm just not sure you're aware how catastrophic of an issue it is. Just one tree washes out upstream (there's a whole bunch of them are literally on the edges pretty much everywhere, so the risk is rather high), it's basically guaranteed to hang up on the bridge, which will act like a dam, accumulating more and more stuff that's coming down. Water is relentless. It'll either completely dam up the creek and eventually wash it out or the built up pressure just break it into pieces. You will be extremely lucky if it'll still be there by the time you get back next summer. Some might say it's borderline irresponsible to leave it like that. Just hope nobody sees this video from wildlife protection or whoever has some authority over there, or you might even get into some trouble. Sorry for the dark and gloomy comment, it's just "prepare for the worst and hope for the best" mentality. This is pretty much the worst case scenario, it might be perfectly fine. I just wouldn't bet on it.

[@LifeonFishCreek]

@@janosszabo98 🤞🏼for a good outcome

[@thomasvontruut]

I cut off my thumb just like that in the woods with an ax and it became an expensive lesson for me but a good experience later on. It was cold and wet snow fell and I got careless which cost me a very long healing time. So be careful and never take chances with an ax, knife or chainsaw. Thank you very much for allowing us to accompany you on your adventure. Looking forward to more videos from your trip there in the forest 🍻🍂🔥🌲🪓 Will you get there when the snow settles too? SKÅL from Sweden

[@LifeonFishCreek]

Unfortunately I will miss out on this winter. But yes I'll be back early summer 2025. Sorry to hear about your thumb. I will definitely be more careful

[@LorneAnderson-j5r]

Great job!!! Just another tidbit. Straps stretch which can make it difficult using a winching system like the one you use. If you can, use cable as chain can be heavy. Also when cutting a tree with a lean to it, most times there isn’t much you can do with the lean but just go with it. Be safe and thanks. From British Columbia Canada.

[@LorneAnderson-j5r]

Oh and you may want to secure the “upstream” logs to something secure. High water may dislodge all your hard work.

[@blakecorkill2137]

great video buddy -that's some tough work you've done!

[@waylonredcalf1251]

If you pull the log on the ground it hard but if you lift with only a bit of log touching the ground much easier on tools you . Good luck bud doing good so far

[@tonysadventures2799]

Love your videos! A chainsaw winch would be super helpful

[@ashleyanderson2859]

Agreed

[@OldSchoolAlaska]

👍👍

[@darrenrsmith7119]

Never seen or heard of that?? 🇬🇧

[@OldSchoolAlaska]

@darrenrsmith7119 the bar is removed from the motor. The attachment is added, which is powered by the same drive sprocket that drives the chain for the saw. It has a spool of cable for pulling loads. Many times, they are attached to a base for stability for a better mount onto a tree as an anchor for an example. Hope this helps.

[@darrenrsmith7119]

@@OldSchoolAlaska Cheers fella 👍

[@paulangerhofer5035]

Good thing you are short in spikes. Log space will help not only with finish weight but allow snow to fall through or snow weight would be that beautiful bridge’s downfall. I’d try to somehow suspend cables above the bridge and run a couple down on each side attached to main beams with lag bolts. Allow for tightening of suspended cables after stretch. Looking Great!!!!

[@LifeonFishCreek]

@@paulangerhofer5035 thank you, you a few others have the same idea... Sounds like it may work better that an x pattern under the bridge

[@greggssausageroll6445]

Holy fuck man, My previous post was BEFORE I saw you hand accident, Spooky or what !! Like I said " Shit happens" Get them there safely glasses !!!!!

[@deadpinecollective]

Love the drone footage

[@gordonharper9126]

Just put a square brace underneath your bridge. Two of them. About 4 feet of the creeks edge in the creek bed. One on each side. And stand them up like a wall. Parallel with the flow of the creek. You can even leave the bow in it that you have. Really easy to replace when they go bad.

[@hippie_james]

Hey bud from the last video unit now I've been waiting to see this video and still great job on cutting the trees like our last conversation

[@mikecrawford7352]

You could cut a branch and prop the centers up maybe an upward arch then nailed them together it may level off after you take the branch out.

[@peteellissnr6258]

Mate. Suspension bridge. Cables strung above the bridge between trees and then droppers down to the logs. Each cable down can be adjusted for tension. The main cables across the stream don’t need to line up with the bridge as they could cross diagonal if need be and just put droppers down where the cables cross above the bridge edge. Hope that makes sense!

[@LifeonFishCreek]

@@peteellissnr6258 it does make sense, thank you.

[@javiermartinez701]

Hello Ty. My respect and admiration for your tenacity and determination to resolve challenges, you're going to be successful in your settlement in Alaska. I'll give you some advices but it's up to you. First of all, to relieve weight to the beams, cut the logs of the bridge deck in halves. It gives more stability and easy to nail it. You answered me that you can't put struts or piles in the river, can you build wingwall or bridge seat in the river bank? It relieves strain to the beams. Also, your idea to add suspension cables is a very good idea and you don't need to build concrete towers, you have close trees that can be used as cable anchor. What kind of vehicle are you going to use? ATV? An ATV with winch will be a game changer! Congrats.

[@LifeonFishCreek]

Thank you Javier, I could build a wall but I don't think it would do what I want it too, a few others have commented other cable ideas from the top side which I am considering heavily. Argo and snowmachine are the two main vehicles that will cross the bridge

[@cath7336]

Im loving this channel. You're doing an awesome job.

[@TraceyPepper-k3h]

You've done an amazing job, dude! Epic is right! Bridge looks lower (than it actually is) in middle depending on camera angle but around the 48 minute mark in video, we get a better angle which looks like plenty of room for floating debris. Your idea re: concrete posts and wires cris-crossing sounds good but I'm no expert. Hope your injury gets healed asap! 🌞👍

[@LifeonFishCreek]

Thank you Tracey!

[@Saskatchewan1984]

I know all to well about getting to close with the axe while making kindling as I almost chopped a finger off and was far from new to making kindling, but it happened in the morning routine , axe went to the bone and what stopped the swing was axe handle hit my pant leg , I was alone so had to toughen up and get it dealt with , grabbed a clean rag and applied pressure til bleeding slowed, then found the first aid kit , cleaned it up , and got a bandage on it , eventually went to bandaid stitches , now the scar is a reminder to think it threw while making kindling lol

[@driverguy7]

Very good work on your bridge! If you mounted metal railings along the sides of the bridge, then wound cabling around the railings, then suspended the cables to high points on both sides, that would work too.... Have a good week!

[@neutonrenda2303]

Spacing the logs is going to be much better weight wise, I think it works well.

[@FishandHunt]

It's coming together 👍🏻

[@dianamazzullo9065]

Like the cable idea for your bridge.

[@kmbjbb]

That spacing is more like those cattle guards farmers use to keep livestock in the place the belong, but no gate required for the "road".

[@captrockh2055]

Rickety Racks.

[@kcbguy57]

Not a bridge too far. Heal your hand and be back at it. Great Job.

[@aannddiiffeerroouuss]

Athletic tape is good and holds well but they also make a stretch tape that sports use for cuts. You should look into that for your first aid... Much better for allowing you to stay active and keep good range of motion.

[@captrockh2055]

I was thinking of a wide board & rope,with a cable & some pulleys - make a overhead trolley you could sit on and pull yourself across the creek. (Zip Line)

[@jellies6996]

You mean something like the one that they have on homestead rescue on the big 40 with Marty Raney and all his family, they made a double zip line that was attached to an old ski lift on either side and they had a little cart that they could.d haul themselves or equipment across a raging river

[@theinvasivespecies1119]

On your next trip I would suggest you nail the centers of each those logs too.

[@theinvasivespecies1119]

Would absolutely love to be helping you!!! Looks epic

[@MD-vp7yn]

It’s a little more work but cutting the logs in half reduces weight and allows the flat side to sit on the logs. We do this to build helicopter pads for logging in the mtns, have a look. Learning to split a log with chainsaw freehand is good skill to develop.

[@LifeonFishCreek]

I'll check it out. And I agree. It probably would be worth it and a good skill to develop

[@mademoisellekaya1438]

Just came to the comments and look if it already was suggested, and you did. I agree 💯 % 😃

[@nancybrown2700]

Your bridge will benefit from the gaps as it will not need to sustain a full snow load, much like decks are built with gaps to allow water to flow through and not capture leaves or debris which cause rot to develop sooner. Good job.

[@earlhildebran1733]

I have a concern of breakup come spring time. Bridge appears to be about 3-4 ft below the bridge at low river. Just a few days of rain raised your level several inches, I lived up there for 7 years and I seen those small streams come out of their banks during breakup. We had streams that were fed by the Alaska Range, 35 Miles away and our creek would fluxate as much as a 12 -15" during the day from melt water even in the fall. JFYI I admire your tenacity in completing what you did.

[@LifeonFishCreek]

If it survives this next spring breakup, I'm raising that low end a few feet higher.🤞🏼

[@berrytyrant]

You could use short pieces of smaller round logs under the tree trunk, like a rollers to stop the trunk from digging into soil and help it move little easier.

[@jameslight4052]

If you installed some upright logs under the three cross members in the river bank on your cabin side in would reduce the span by about 6 feet and help with the flexing.

[@LifeonFishCreek]

Appreciate the tip, thank you

[@knolltop314]

Well done!

[@tdk1246]

What about a suspension bridge instead? May be easier to build and higher up from the streambank. You would need four upright logs - two for each side of the bank. Run steel cable across the top of the uprights and across the stream - one cable for each side of the bridge. You can anchor the cables to a nearby stout treat or if you care to lug cement in - I'd go for the stout tree. Next, hang loops drown from the cross cables to hold the cross planks. The cross planks will form the bed of your bridge - can make these out of half-logs. Then tie all of planks together with thin poles to keep them from swinging. That's it.

[@robertwilliam7828]

Before you cut a tree down lay down small roller logs where you think it's going to fall to make easier moving the tree

[@wallacehammond4825]

I am writing at about the middle of this video before you have placed any cross logs so I am probably too late but I would have split those logs before placing them. A. they would be lighter, B. they will lay flatter and the nails will hold them better, C. you will only need half as many and D. when you split them in half you will mitigate the the size difference of the logs by 1/2.. I am also concerned that you have built this bridge op property that you don't own. Lots of work improving someones elses property.You are a tough Dude. Keep up the good work.

[@MD-vp7yn]

There is a concept I think you should look into. It’s called a force vector. When you apply a perpendicular force to a tensioned line or cable you magnify the horizontal force on the line/cable considerably more than the downward force you apply. Try to avoid horizontal tensioned lines when possible. Having any kind of U reduces the tension so other comments about lifting the bridge from a U line above is a better idea imo. When you were lifting that log in place running the strap over the cord I was cringed hoping it wasn’t going to snap into your face. Just be cautious running nylon over nylon and also tensioned lines…good luck !!

[@LifeonFishCreek]

I will definitely look into this

[@KevinBlanchard11]

This is wicket buddy you have come along way

[@JoHarmon-hg7wz]

Add some New Skin to the first aid kit, great stuff closes up wound and stops bleeding fast may have to add it a second time with a really bad cut.

[@AlecBell-b3f]

I feel worn out just watching all that work you've done. I, like many I suspect, started thinking of how I would do such a bridge. Have you thought about an "arched log bridge"? Something like "Grandpa Amu" or "Backyard Trail Builds" have videos of building, or even a Davinci bridge? Both use shorter, easier to manage sections, have good load capacity and could probably span the distance easily. Just a thought. I can't wait till the cabin build starts. You're living the dream so I may be a bit envious (Oh OK, a lot).

[@MrScipio72]

That bridge is cool - but what a lot of work. I hope it works out and makes your life easier next year and into the future. Hope the hand is ok too mate. Thank you for sharing this start of your new life. PS - please get a large hammer onto site next time. Wielding that sharp axe as a mallet made me very nervous.😁

[@LifeonFishCreek]

@@MrScipio72 for sure need a big sledge. The hand is nearly healed up. Thanks😊

[@redcanoe9810]

We found debarked logs last much longer. None the less, I fear your bridge will be washed out in the spring... Nice going!

[@nancybrown2700]

Another addition to your first aid should be super glue. Once you clean a wound it works like stitches to help seal and heal a wound. Hospitals often use a super glue equivalent rather than stitches. Have peroxide on hand to initially rinse out any wounds. Next time in town get updated on your tetanus shot too.

[@ElizabethShaw-h9z]

Lemon slices inthe middle of no where,spoilt it for me.

[@LifeonFishCreek]

Lol, that's funny

[@ShameReaper]

You need pillars somewhere in the spans to support your bridge.

[@johnhaldane8895]

Respect

[@robertallan9601]

Have you considered an mt barrel with both ends removed (leaving rim lip in place) & use it as a caisson to place concrete centre supports for your bridge in the creek ? a bottle jack could then lift the bridge to allow permanent support to be installed. just an idea.

[@shiammi907]

Because we know that's not actually on your property------> *Did you get the proper permits from the State of Alaska to build the bridge and cut the trail to it?*

[@LifeonFishCreek]

@@shiammi907 no permit needed for what I'm doing. State land can be used to gain access to remote properties without a permit

[@shiammi907]

@@LifeonFishCreek Ty, just as you have "licensing rights" to your stuff listed in the drop down menu, and another person would have to receive permission to use it; the State of Alaska requires you to receive permission to use its stuff too. You have to obtain EASEMENT authorization. Look up DNR (Department of Natural Resources) Fact Sheet: Easements (PDF). My family has lived here for generation upon generation for centuries upon centuries and even so must still receive proper authorization when it comes to state land in the Great Land.

[@edwardroxas1574]

And lift the lower end of the bridge 2ft from where they are now.

[@waylonredcalf1251]

You know if you put your pull ropes come along strap up high in the tree to pull your log . It would be much easier. Your pulling along the ground so much friction with your log right .

[@braddunlop7819]

Split your crosser logs lengthwise

[@darrenrsmith7119]

I just read the ' More ' explains you can't put anything in the water to stop the flow or hinder the salmon run, surely just a single fat log under the bridge in the middle won't affect it?? Do like the strap and concrete idea. Will need to be hi, GL dragging those posts, I'd get a friend or two to help with that.. Gl and see you, will keep this channel and looking forward to next year... All the best 🇬🇧

[@darrenrsmith7119]

Just use ya hand n go across the water and add the logs as my math is says no way you need that many, then again my math always adds extra inches 😂😁🤭🇬🇧👍

[@darrenrsmith7119]

Is saying** no way Before a noob catches my bad grammar 😬

[@theinvasivespecies1119]

You are really going to need to secure your bridge to each bank because of high water. That creek WILL rise and wash it out. Water very destructive. Overkill the bridge secure

[@THE_CarpetMan]

Great job mate hope you can get back and get more videos up soon .....would b great to see a winter video..

[@SEA-U2]

Wow Sorry you Hurt Your Hand That's A Big Cut😢 Incredible Work you did for Sure💪Hard Work Always Pays off😊 I Think the Cable Anchor is A Great idea and Two Anchors to hold the Bridge on each side to keep bridge tight when water Rages? What do I know 😅😂 I bet alot of people out on KZbin land Really wish they could have helped you me included But That would have defeated your purpose of being alone I could have watched you All day Long Really Amazing Stuff 😊💪👍 Enjoy your time Off And Hope To See you Soon on Your Next Mission 🙏😊❤

[@LifeonFishCreek]

Thank you, I appreciate your kind words. The Hand is nearly healed. Another week and it'll be just a memory

[@theinvasivespecies1119]

You should buy a chainsaw winch. Basically a winch on a chainsaw

[@JalinGregory]

Great drone footage. You should work for national geographic!

[@marktoland9206]

I absolutely love your videos! I admire your hard work and determination. I am a bit concerned, have you considered high water levels and the effects on the structure? I'm sure you have, I would hate to see all your work washed out by a wet spring.

[@LifeonFishCreek]

I have yes, check the description, I explain it there. Thanks for your support. Let's hope it's still there when I return🤞🏼

[@bertgriffin3624]

Dude, a driving bridge ? You had better put cables under that thing.

[@tylerhoward2703]

needa bug net/mask my man by the looks of it it would make you a bit more comfortable when it comes to those bugs

[@LifeonFishCreek]

@@tylerhoward2703 I had one, just didn't want to wear it

[@jellies6996]

How about a covered woodshed near the cabin so your wood is dry in the winter ?

[@LifeonFishCreek]

On the big ole list of things to do😊

[@bcnewfie494]

build a crib under the bridge in the middle have it v shaped upstream to redirect water ice etc

[@Saskatchewan1984]

No sure if you already have a Argo , or what your budget is for getting a. Vehicle to get you to your property , but if was me I’d spend the money and get you a 6x6 canam defender as it has a 6 foot box and an haul a lot or 6x6 Polaris ranger , they can haul a lot and go threw stuff great , and believe alaska bush tracks can make a track for over the rear wheels , to give you event. Better traction and floatation , argos are great but have to keep up with maintence which is alittle more then side by sides or atves , and unless your crossing deep water a lot or marsh land , I’d choose a sode by side or atv over a Argo any day , that’s my opinion as a recreation tech I work on Argos and atves and side by sides , definitely prefer side by side and atves over Argos , belive Alaska bush tracks has a few video on Facebook of defender 6x6 with there tracks

[@LifeonFishCreek]

@@Saskatchewan1984 I'll check this out for sure, thanks for the info. I'm pretty sure the few hundred yards of marsh can get pretty bad at some points in the season

[@Saskatchewan1984]

@@LifeonFishCreek depending how often you plan to use the trail or how much weight you plan to haul over it , the marsh areas it may pay for you to make a Corduroy road over them areas , which is making a a trail across by laying trees down across it to drive on so you don’t sink in and tare it up , as marsh areas tend to get bad the more you cross them , so over time could get harder and harder to cross ,

[@tiemen88]

Maybe don't do bumper rails on the side. Just to save weight.

[@LifeonFishCreek]

@@tiemen88 unfortunately I have to add those so I don't accidentally slide off the side of the bridge

[@riaandebeer8419]

instead of adding concrete ( a unnatural product) in a beautyfull natural environment, add posts under the bridge in the creek

[@riaandebeer8419]

you see while nailing in the last spike how the bridge behaves like a rope bridge, posts under the bridge will most likely eliminate the "sway" or gratelly reduce it aswell as add structural and weight carrying capacity

[@bigthasher7958]

why dont u do a heavy wire haft way down the bridge to haft way up the trees then that way u will take the bounce out of the bridge and then chain or wire it off at each end so it wont move

[@larrythacker2844]

Great job and you are making good progress. Is the bridge high enough for spring run off?

[@LifeonFishCreek]

@@larrythacker2844 check the description of the video, I talk about it there.

[@ervintaylor6508]

Split the log with your axe?

[@rongoris3022]

Youch! That looks like a nasty cut! I always wondered why more people have not cut themselves with an axe when making kindling when I saw one guy come up with a very simple but effective hack. Instead of using your hand to hold the piece of wood when swinging the axe use a stick. This way it keeps your hands far away from the blade. When I first saw him do it I went "Wow! Simple and effective!". One other thought. Are you going to put large stumps under the center of the bridge to help support the weight?

[@LifeonFishCreek]

@@rongoris3022 I usually move my hand away, but this certain piece of wood would not stand up on its own. So I held it steady, dumb mistake for sure.

[@cichlidsandmore63]

Just cut the log to get the nail out