The Very mojor Repairing Of Broken Differential Gear Ring By Very Brilliant Mechanic…

[@coldpond]

As long as one doesn't drop it, it should look good in a glass showcase.

[@lkeil84]

These videos are fun to watch and snicker at. But don't think for a second this thing actually worked.

[@arkanoid1965]

Сработала, они на просмотрах зарабатывают, а не на ремонтах.

[@awardnamir6794]

Instead of criticizing, just help them with practical suggestions and solutions. There are correct physical methods to return matter to the way it was

[@intheshell35ify]

​@@awardnamir6794no. You can't unbake every cake.

[@yaakw]

They don’t have high rpm intersate highways. They got low speeds, lighter loads most often and bulky lower weight loads. Roads are bumpy toput it mildly.

[@intheshell35ify]

@@yaakw I routinely braze up a ring gear missing tooth on old farm equipment. It's a 50/50 proposition. This will not work at any speed.

[@Smarts85]

Отличная работа, теперь не стыдно выбросить 👍

[@claudiovarnerin5795]

🤗

[@Kot_Anatolyi]

Это постанова. Шестерня так никогда не ломается. Они специально сломали, чтобы ролик снять

[@Cepera03]

Долбаный Боливуд!!Главное чтоб красиво было - блестело!!!🤣

[@avoiddegroid7697]

Outstanding! That expert repair should last at least ten miles before the gear grenades somewhere. Well done!

[@johnye4433]

This is a stress induced fracture over a long time, just like a heap replacement, you got what you pay for if you can manage the stress long enough to junk the truck

[@Refertech101]

they may even carry a load for a bit!

[@prinz10ga]

Here in well developed countries. We believe the only way to repair anything is with the preciseness we have available. However these countries are so undeveloped that they are using the analog machines of our grandfathers. They McGiver the best they can. There are no schools at any level. Children are endentured to lean a skill that’s been outdated for many decades. All of that said, I think we all would be surprised at how long this gear will last before failure again.

[@Thankz4sharing]

"That expert repair should last at least ten miles..." No miles to be found over there. But it won't last 10 km, either! Up a steep hill with a heavy load? It will fail the first time the pinion engages the "repaired" (ha!) ring teeth.

[@deezelfairy]

​@@prinz10ga You're talking shite - this repair wont last 30 seconds for a whole host of reasons that i cant be bothered with explaining. Honestly, i think these 'Pakistani mechanic repair' videos are just trolling for clicks at this point.

[@sylviaelse5086]

The pin hole positions were measured, but I didn't see anything that ensured that the the pin holes will be along the same axes in the two parts. Do these parts really have to be repaired anyway? I'd have thought plenty of trucks would get written off while leaving these parts intact for resale.

[@nikspanakis]

There was a cheaper and exactly same strength way to fix it. Flour glue.

[@flouserve]

A ellos les vale así, todo antes que buscar una pieza nueva, pero les va a durar con suerte unas horas antes de que reviente de nuevo

[@Sussilando]

oder Sekunden-Kleber😂

[@silvanoRV]

Crazy how a brand new ring gear splits directly down the middle, no wear marks, fairly clean metal...

[@chylimzbydzi]

Why put the gear on a flat surface if you can put it upright? Very brilliant!

[@ВалераКонстантинов-и2ч]

Сдаётся мне что, это была комедия, Пакистанский юмор

[@alexeydybov875]

Конечно! Мы обеспечиваем просмотр, они зарабатывают. Какой здравомыслящий человек поставит подобное изделие для дальнейшей эксплуатации в мост?

[@claudiovarnerin5795]

​@@alexeydybov875 mai! solo in caso di guerra (in ritirata) 🙏🏼

[@johnthompson3605]

Ha Ha a hypoid crown wheel and pinion, only THE most precise gear set in any vehicle , we used to make these for Leyland trucks and they are absolutely pot hard , glueing it back together does not mean its repaired it means its now one piece again , give it about 20 mins lol

[@МихаилВолор]

Двадцать минут - это много. Сварка выжигает углерод рядом со швом, значит свойства металла ещё изменились в худшую сторону. Штифты из низкоуглеродистой стали тоже добавляют концентратор напряжения. Этот дифференциал под нагрузкой минуту проработает. Ну, а нарезка зуба болгаркой - это высокие технологии размерной обработки материалов машиностроения, да.

[@АлександрМальцев-ч4т]

Как раз минуты хватит до следующей мастерской доехать))).. Их там много)

[@istvanfazekas151]

Maybe it will break itself on the first turn if it turns around at all.

[@furiosilvagni7622]

L' avranno riparato per metterlo in vendita in perfetto stato 😂😂

[@fishin11]

SO much wrong here!!! Will not work, tolerances are WAY off now, especially when he puts it in the lathe and grinds the back side. Unless they shim the back side of it now the run out against the pinion gear is way, way off!!!!!

[@arthurgay5746]

Now that would be perfect to use for a clock on the wall in your shop but to put it in the rear end of a truck that's gonna be loaded up with three times the weight of the truck's capacity, it won't make out of the parking lot !!!

[@CarlGraber]

I'm impressed with the workmanship! Lots of details and efforts! It's a piece of art!

[@механикмеханик-э9л]

если они ставят тройную раму на грузовик то этот редуктор не выдкржит и рабочего дня

[@n5ifi]

Exactly, Remember too that this is a specific alloy steel and they are heat-treated to improve surface hardness, ensuring the gears can endure high levels of stress while maintaining durability over time. Their going to weld it with a 7018 rod. It all looks good on video but won't work until the oil gets hot. It shows you how stupid they think we are.

[@бабай-ж3м]

Сработала, они на просмотрах зарабатывают, а не на ремонтах.

[@АртемСолодовник-ы6ф]

Это пойдёт на продажу)))

[@zackkasey]

Legend has it the mechanic trying to put the ring gear back in the rear diff still hasnt found enough shims to make up for all the material the guy shaved off on the lathe. 😂

[@活生-j3s]

It won't last long like this, the idea is too simple and not strong enough. The correct way to do it should be to grind the bevel, then find a flat iron plate and use the holes to fix it, then weld it on, then remove the iron plate to fix it, and make comprehensive welding adjustments, making sure that all the broken parts are welded in place, so that the strength will be higher.

[@istvanfazekas151]

I wonder how precise gears can be made by hand? I think it will be destroyed due to the lack of accuracy, if it will rotate at all.

[@timmyhipbird7543]

no the correct way is to replace the gear set.

[@kenc3288]

This is nonsense, this is a hypoid or spiral bevel crown wheel and pinion set. The material is through hardened or case carburised high alloy material. YOU CANNOT repair this and expect it to last more than a few minutes under load. You do not understand the precision or heat treatment required for high performance power transmission. Buy a new gear set. How stupid….!!!😡😡

[@kamaev_petr]

Это не чушь. Вполне рабочее решение, давно так делаю каждые 2 км, уже проехал почти 100 км.

[@josepeixoto3384]

he´s been doing that for over 10 years, broken gears and shafts come from all over to his shop, this is not USA, he does use special electrodes, and the parts last as good or better than new.

[@hardergamer]

@@josepeixoto3384 HAHA.

[@ВасКо-в2с]

This is Pakistan - people there are poorly educated. They don’t know what mathematics is, nor physics, nor chemistry, nor what strength of materials is.

[@PeterChapman-rg6gr]

@@josepeixoto3384 The "Electrodes" that have had their identification visible are "PackBridge" which is a very basic low strength general purpose 6013 type,

[@alexgann4039]

Держать не будет так как сварщик не в резиновых шлёпках!

[@kurtler1]

1:40 готово можно забирать 😃😃😃😃😃

[@tviyagrosvitvm3121]

Сварить и прибить на стенку гаража.

[@Валерий-ю1м]

Сварить, обточитьи отправить в Россию как запчасть.

[@numailer]

That's pretty much all it's good for after a repair like that.

[@marsmars9130]

Whats amazing is that it took 2 of them to carry that

[@alanwelch6594]

This is KZbins newest comedy ensemble. That gear is hardened steel. Welding hardened steel destroys the heat treatment, causing the metal to be too soft. Any metal added by welding is mild steel not capable of being quenched and tempered. That gear will not last at all if it is installed.

[@Валерий-г4и1г]

Вообще ничего не знаешь в закалке, сварке , и судишь по своему недалекому уму.Главное - кто сварщик. А приварить тракторный поршень к строй арматуре 32 мм с Rшва среднее значение между металлами - слабо.

[@honkie247]

@@Валерий-г4и1г No, in general YOU know nothing about hardening or welding. At best it is a waste of time and an opportunity to fool people who are not familiar with this type of repair and it's failure rate. In other words......CLICKBAIT.

[@alanwelch6594]

@@Валерий-г4и1г I was a professional welder for 12 years and I still occasionally weld while blacksmithing and bladesmithing. What does a hardened and tempered gear have to do with a piston?

[@artszabo1015]

@@alanwelch6594 Don't stress him out, he is looking up piston in the dictionary so he can answer you.

[@danneumann3274]

@@Валерий-г4и1г I have 4 heat treat furnaces and heat treat on a daily basis. It is true that welding steel destroys the heat treat. This gear with its pinion might be one of the most stressed parts on an automobile ( or truck) everything must be close to perfect for it to hold up. this would likely be gorged, then deep case hardened to that the interior of the gear ring is on the softer side. have You ever machined through an arc weld?

[@ВасКо-в2с]

I look and believe that by marking the center for the pins with a marker, you can achieve precise alignment after drilling on them...

[@John-oe5nb]

Any MOJOR repair should hold up just fine. Guarenteed for one revolution or 5 seconds whichever comes first. The MOJOR repair should have been done with Super Glue and it would have lasted longer and wouldn't have taken so long to "Fix".

[@Ascrappy1]

I didn’t know they speak “Chipmunk” over there! Say hi to Alvin for me. 😂

[@ETHel1903]

Because the playback speed has been speeded up.

[@Ascrappy1]

@@ETHel1903 Duhhhh! It was a joke! 🤪

[@Markcain268]

Like the goons yingtong song

[@trainnerd3029]

Take a minute and truly understand why these types of videos are made. It’s entertainment! Hope this guy gets lots of likes and subscribers, and makes a couple bucks for him and his family by doing this… Respect!

[@autophyte]

Yeah.. That's why I watch them.

[@Cepera_52]

У меня кровь из глаз потекла, они шестерню редуктора сварили!!!😭 Вот так же , только красная и зубья болгаркой нарезали, жесть!!!

[@АртемСолодовник-ы6ф]

Где-то было видео как подшипники варили😂😂😂

[@thomaskirby6706]

Great work, but I must have missed him repairing the damaged teeth.

[@ВладимирСуржиков-п8п]

Прекрасный сувенир на стенку.

[@nikolaygorbunov5745]

Я тоже так подумал, повесит на стенку в рамку, и скажет это я насрал

[@adnacraigo6590]

I bet you could hear it roar😊ing from a long way off. It was interesting to watch though.

[@timmyhipbird7543]

when Atlanta was building the airport extension the trucks hauling the dirt called it the mud pit breaking gear sets once a week.the owner kept the old gears and when he had a good ring gear he'd match it with a good pinion.he didn't care it whined down the road he'd be putting another in later.when he finished hauling there he got a new matched set installed.

[@PILOTabcdce]

полевой ремонт!) ходить конечно не будет, но до места потихоньку может груз дотащит, а там уж новую главную поставят,,, если не забудут😂😂😂

[@АртемСолодовник-ы6ф]

Если с грузом - такого ремонта хватит километров на 5)

[@SergeyKingFox]

Работа страшна своей бессмысленностью!!

[@carloskellerman2990]

He sido metalúrgico durante 60 años en un país pobre, pero esto es demasiado. 😮

[@Ghadiali]

I always love watching your work. 👌👍💖

[@kennethhorton225]

Is this company named W.E Bodgit & Scarper? A "repair" like this is false economy as the next time this part fails due to this bodged repair it could very possibly damage the entire machine it's fitted to, plus injure the person operating it.

[@timmyhipbird7543]

heavy population there no one cares.look at all the safety equipment.

[@tomxavier4328]

Precision emgideering and workmanshit.

[@ttinnovations3310]

my wife will say the same thing, this will only last 3 min, you need to do better

[@robertrobbins5456]

I too, would love to find out how far it went before exploding in spectacular fashion!

[@dan-o9746]

Now it can be used to prop a door open

[@Diyan2008]

Такого безумия я еще не видел))) На раз тронуться)

[@alvaropereiramateus5861]

Parabéns ,,fez um bom trabalho 👏👍

[@Osaka_1101]

割れた陶器を手で戻そうとして虚しく感じる事がありますが、鉄の場合に不可能は無いことがわかりました。

[@alro2434]

Thanks, I like the acting/pantomime in the beginning!

[@stevo184]

Including the unedited bit where he fell over😂

[@williambrandley623]

Brought to you by the folks who make all the perpetual motion machine videos!

[@josel.melendez6322]

The broken diferencial gear completly lost the original dimensions and restaured probably take a lots time and efforts, good locke.

[@nicnic1434]

Хвала мастерам, спасибо за видеоролик

[@KuriakosePolayil]

Absolutely amazing beautiful video congratulations ❤️

[@stevo184]

It's going to break within minutes.

[@inviz88]

This is hilarious! I'm not a machinist but even I know this is the biggest bodge job on earth lol Thanks for the laughs. Was funny to watch you burn up your insets on the harded gear. And turning a circular part into a oval lol.

[@BiraQuintanilha]

Ótimo vídeo Excelente profissional 💯👍

[@evergallardo8259]

Parecia un trabajo serio, hasta que lo soldaron superficialmente, ese engranaje no va durar ni una vuelta

[@jamesdegraff]

These are the people who survive the apocalypse. While we all watch and tell them it will never work, they make do with what they have. Truly remarkable what they can do.

[@craigc4334]

They’re the people who die horribly in the apocalypse

[@mattsan70]

A rare peek inside The Boeing workshops.

[@БрюсикЮсик]

И смех и грех 😂😂😂. Великие деятели.Сизифов труд.

[@bluesteel48]

Should have started this repair using a scrap metal furnace.

[@OppoA3s-s6m]

Best Job , Expert Mechanic. Thanks All, ..... Cheerio.*****.

[@Berlyangulo]

ESTE TIPO DE TRABAJO FUNCIONA PARA UNA EMERGENCIA, PERO PARA UN TRABAJO PROLONGADO TENDRA NUEVAMENTE LA MISMA FALLA, LO RECOMENDABLE ES CAMBIAR EL PIÑON Y CORONA NUEVO.

[@matthewnagy3310]

Some of the repairs these guy's do is spot on. But be realistic just go buy another ring gear ⚙️ 😂

[@pedroledezma5111]

que tipo de electrodos de soldadura usan para esa reparación, saludos , muy bueno el trabajo que realizan

[@jeffo2112]

Very impressive.. How long compared to new will this fix last?

[@normanedwards7220]

WHY .would you cary a broken crown wheel and pinion on a stretcher / bed to be repaired , .......why ?

[@mj6749]

First thing I noticed was the cement floor. Definitely an up-market workshop.

[@josepeixoto3384]

Is that in the USA? the man does really amazing work, notice his safety sandals too.

[@DJAndrewGaylor]

it's obviously in India

[@ambrosiorm8960]

Ni en EE UU ni en ningún país donde se cuezan frijoles 🇪🇸 carajo!!!😮

[@Universal-Dilettant]

@@ambrosiorm8960 Does it matter where this happened? The transmission will break again within seconds anywhere on this planet.

[@MM-vk4ip]

And this is why you get a Carfax report

[@sckapex]

stupid idea, it cannot last on load.waste of efforts and money. buy new pair ,it will be cheaper in long run

[@Gundalaputrapetir-o1w]

If it can be complicated, why make it easy? 😂😂

[@philipveipert7663]

I will never get over the danger they put themselves in. Wearing baggy pajamas while operating a lathe, welding in sandals and never see them wearing safety glasses. 😂😂😂

[@markjapan4062]

SHIT OF THE EARTH GOD CUT THEM OFF WHEN HE MOVED ABRAHAM

[@shawbros]

You do not understand safety sandals. Safety sandals will protect everything.

[@ОлегКоробкин-у7е]

отлично сварил, теперь эту шестерню в металлолом, а на мост, поставить новую гипоидную пару!

[@АлександрНороха-б7л]

Как нас дурят с таким ремонтом

[@sergeioleinik1894]

Она в Россию поедет в магазин😢

[@LesleyStoddard]

Welded teeth have a bad mesh and hardening. Bang!!!!!!!

[@DaveyD71]

Good Lord. Their next repair is a cracked piston repair with silver solder. 😂😂😂

[@castetmuchachosanhesderami8911]

Это шоу сварщиков и токарей😂главное просмотры!

[@ВалераЧерный-э9ф]

поддерживаю, уж больно чистые актёры)

[@Noni1975]

These guys would be in high demand in Mad Max's world

[@1TOPSPEEDPERFORMANCE]

ha ha come on, this a joke,none of these repairs work,but they make money from the views like the welding broken cranks.they are having the last laugh

[@Сержпаврпао]

Завариваю чай и достаю печеньки😂

[@Arslan-rc3iu]

Буду смотреть 👀 и бояться...

[@Manuel-mb4zb]

Wie lange das wohl hält? Interessieren würde mich das schon.

[@joachimpohle5260]

Ich glaube nicht so lange mit dieser "Stift" Technologie. Das ist ein heftig beanspruchtes Getriebezahnrad, kein Ikea "Billy Boy" Schrank. Das müsste Minimum so geschweißt werden, daß jedes Eisenatom des Zahnrade miteinander verbunden ist. Dafür müssen die Teile anders abgeschliffen werden und die Vermessung könnte ein Problem werden. Muss ja alles genau so groß werden wie vorher. Murks. IMO

[@radhikatommaso873]

Holding a gear in the vice by its teeth could damage the vice!

[@ridwanbulu1200]

Saya tidak habis fikir dengan orang-orang ini🤦‍♂️🤦‍♂️🤦‍♂️ saya mengapresiasi kreativitas anda👏👏🙏🙏

[@masnurangtennang9482]

Tahan berapa lama kira2 itu ya, sedangkan msih asli blum di las terbelah dua apalagi ini di las jadi terbelah empat nanti.

[@thedolphin5428]

0:30 The patient is brought to Diff Hospital on a stretcher by the Ambulance.

[@LanDaiLyLife]

Good morning ❤❤❤❤

[@iskandarmuda275]

Harganya tak seberapa,,dibanding dibubut kembali,,mending beli saja baru,,,merusak citra negara.

[@Gundalaputrapetir-o1w]

Justru saya mikirnya semua di perbaiki kenapa ya... Bearing aja disambung padahal sudah patah jadi dua. Semoga dapat jawaban yg benar dari ybs. ❤

[@feelsick9800]

baya, what material used for steel cutter head?

[@alexeydudin3849]

Планетарку на кровати - это шедеврально😂😂😂😂

[@ivanivanov251]

It would be much better if the masters danced from time to time. Было бы гораздо лучше, если бы мастера время от времени танцевали бы.🧑‍🔧

[@windi121]

Very good work indeed

[@eduardoliranza3527]

Dicen: La necesidad es la madre de la invencion. Maquinar esa corona en un torno no se invierte demassdo tiempo, luego llevrla a una frasadora y gravarle los dientes elicoidales es muy sencillo, luego darle tratamiento termico y se acabo el chiste, claro, todo tiene un costo, tambien comprarla ya lista seria un mejor opción, si ella se partio ya, no creo que por muy bien que quede va a soportar el trabajo que hace dentro del diferencial.

[@Bugging-b6h]

Do they can fix space rocket also??

[@geoffreyhicks53]

Now throw it in the dustbin

[@morrisschwarts4826]

And it didn't make any noise at all after it was installed.

[@viktorzhuzhu8256]

How long will it work after such repair?

[@rolfzeller3072]

Wer ein richtiger Mann ist, schweißt ohne Augenschutz!!!EINS!!!ELF!!

[@zr7699]

I have never seen a lathe get things red hot like that! I also know nothing about lathes !😊

[@kevinrandall8327]

Now that he’s machined the front of the crown wheel I hope records how much he’s machined off, all that machining will move the crown wheel further towards from the pinion. That crown wheel looks like it came out of a large lorry, probably a 10 tonner they converted into a 40 tonner.

[@carlnapp4412]

Were did they finf that rusty scrap?

[@ianbates1312]

Am I REALLY seeing someone TRYING to repair a crown wheel and pinion set, or am I dreaming. I’m the fool for watching it to the end!! 😂😂

[@Владимир-л1з7е]

Хорошая шестерня накрывать в бочке квашенную капусту

[@dariodarecki]

Chyba najlepszy komentarz do tego gówna co on zrobił🤣🤣🤣. Pozdrawiam.

[@teamthonquetv5115]

Rất hay

[@seanwatts8342]

This will hold almost as long as JB Weld.

[@stevesantiago9660]

If after repairing it you realize that you repaired the wrong one you can always use it as a boat anchor.

[@yojo619]

Hi Tech Pakistani technology 😂😂😂

[@tomi935]

🤣🤣🤣

[@rolfzeller3072]

Die persönliche Schutzausrüstung ist beeindruckend! 😖

[@kevinrandall8327]

Imagine how loud that diff would howl if the repair was strong enough to hold together. The one thing I have noticed is this bloke is wearing shoes, but no safety glasses, at least the floor is clean.sorry I’m wrong about the shoes they’re scuffs.

[@vladimirmakliasov5739]

At the beginning of the video i was sure they brought dead body for revive.😂