Ported Coocheer 6200 vs Stock Wemars 6200 Chinese clone chainsaw

[@jamesh8136]

Hello I'm curious which tachometer you used in the video and possibly where you purchased it at?

[@novicelumberjack]

Oppama pet-304. Ebay.

[@timberslasher4899]

Held my attention cause I ain't ever even heard of these saws...🤣

[@matthewknight5641]

I saw your 550 build and was really impressed. Do you think I could do a base gasket delete or a pop up piston and get good gains from it on my 550? I'm not sure if it has clearance for all that without machine work but I'd appreciate the advice if you know . Thanks in advance and I appreciate the videos I'm learning alot

[@novicelumberjack]

NO! On the 5 series saws, even just a base gasket delete requires you to shorten the cylinder skirt. If you remove the gasket and then just put it back together, you will fold the cylinder skirt inward and ultimate doom awaits!

[@matthewknight5641]

@@novicelumberjack man I appreciate you telling me that bit of info. It definitely kept me from destroying a almost brand new saw.

[@enginerd1776]

Have the wemars 5820- it also measures out at ~55. Hunting for a jug/piston that isn't garbage to swap, was thinking that the Husky 357 would be a decent start. Will send an email with measurements when it arrives. Thanks for the vids!

[@ericvortex5213]

the Aliexpress cylinder at 20 euros delivered (~22 dollars) is correct for these machines. diameter 48 (62cc) called here "58-3". the numbers are limit high, would be better a little less strong, they are the following without gasket base: intake 158 duration. transfers 127 duration. exhaust 165 duration (97.5 from TDC). the piston clearance is very correct, I am rather surprised by the manufacturing quality, we have seen much worse.. Cylinders with too high numbers can often get good torque and power with an intake vortex just after carb, for better filling and better mixing. Vortex in 0.5mm stainless steel with mini 8 very fine blades, preferably sharpened, otherwise the result can become bad. Bad vortex = bad result Good vortex = good surprise.. This Aliexpress cylinder did not need intake vortex (without base gasket) to work well. Thank you for this video 👍

[@jackfrosty79ify]

Have you done joncuter yet

[@patrycklealoliveira8106]

Hello from Brazil my friend Can you try to help me, please? My chainsaw has a problem with excessive compression. But when I remove the spark plug the piston rotates normally. Even placing your finger in thze spark plug opening causes the piston to become extremely compressed again. Yesterday I installed a completely new cylinder and piston, but the problem remains. I changed the spark plug, removed the carburetor and exhaust fan, and still the problem remains. Do you have any idea what it could be? Can I send you a video showing the problem? I have been seeking help with this mystery on various social media channels, Instagram, KZbin, but no one has been able to guess what could be causing the problem.

[@Turboboob]

It’s in your pull starter assembly… would be my best guess

[@kingsaws]

What are they clones of ? Zenoha?

[@mr.somebody1493]

yes

[@kingsaws]

@@mr.somebody1493 what is zenoha

[@mattfleming86]

@@kingsaws Think older redmax

[@mr.somebody1493]

@@kingsaws Sorry, I meant Zenoah, they are owned by Husqvarna.

[@mattfleming86]

@@mr.somebody1493 Yup that happened about 2007

[@Mark-Marine]

As we spoke, my Wemarrs 6220 IS well made, though the assembly of the ignition is toy(ish), the oiler is barely functional, the chain tension screw is laughable, and its power is more in line with a quality 45-50cc saw. The last part I’ll address (hopefully) with a tuneup. What do I expect for $145? This saw.

[@novicelumberjack]

Send that thing back! Out of all those things you just mentioned, the only one that I can relate to is the chain tension screw. The two that I have owned have oiled great, the ignition system is fine, and the power of my 6220 is better than that of my Husqvarna 55. So...something is wrong. Mine both came VERY rich from the factory.

[@yungsmile7546]

Your patriotism for Ukraine 🇺🇦 is admirable, sir. Thanks for letting us know in detail that the Coocher is not considerable.👍👍

[@aaronpowell4885]

Very nice of you to send that👍 I'm sure they'll be very grateful! Need to put more time on my wemars 6220 to form a solid opinion but so far, it seems like an incredible value!

[@mr.somebody1493]

Lean it out by running 25:1 gas oil mix.

[@joshuajohnson4396]

Crazy. Those Weiner saws actually do ✂️

[@AlfredoMorales-z2u]

Is going to the solders

[@jamesb6899]

Great looking wall hangers I have one 😂

[@nseric1233]

I have a couple of these types of china saws. The ones with quad transfers run better than the ones with dual transfers. I recommend the joncutter 5800, it has the better cylinder and runs good. I also have an older timberpro6150, it's 61.5cc and a good version of this clone, it really rips with a bigger carb. There's an intake block on ebay that lets you fit a 372 carb onto them, it's a big improvement power and rpm wise, I gained about 2000rpm in the cut with that mod. My joncutter cuts at 13000rpm.

[@modifiedchevy]

That's awesome what do you have to look up to find that? I used a metal broom handle and silicone to do the same thing on my garwinner be nice to have a actual intake. 16mm vs 10mm definitely a huge difference

[@mr.somebody1493]

Put the nitrous kit on it

[@novicelumberjack]

I've got something super special coming up with the nitrous kit. Probably gonna see it around February time frame.

[@kingsaws]

I like the idea of the tapered ports .

[@zachdiehl3401]

I love my wemars great saw for power and durability

[@modifiedchevy]

Geezus 92° exhaust roof? Id buy another 12 dollar cylinder and piston off Amazon my garwinner was 102

[@DaveyBlue32]

When those orange “ choocher” I thought there was an h up front…??? About 5 years ago I grabbed one for a hundred bucks and then I had a guy outside of Philadelphia that had bought a cargo container I’m assuming because he had about 20 left and he was done selling them…. I counted his 75 with 50 apiece and he jumped so I must have been around what he paid…. ??? Mines orange and 6 years old and it’s a running son of a gun… I’ve been looking and with a 45mm bore they have to have a little more stroke to get to the 60CC’s? I’m going to have to rip into that at some point but entirely too many good saw’s to knock out before I can waist any time on that one…. On your porting numbers remember that you lower your intake and you make more power but after 60… or so you really start eating lots more fuel for that small addition power… and it’s often much better to simply remove a pocket from your piston as the more material that you can remove from your pistons th you make more power but have less fuel robbing properties…. There’s a lot of wasted pistons material on that 372 Xtorq and buy simply cutting the additional 1/2” of piston skirt off your lighter in rotation and faster to throttle up and hold your power longer…. Be really looking at any additional material on your pistons before your grinding away from your ports as it’s much more work to finish them up nicely and with a piston it’s a quick little roll to smooth with some 1000 grit… anyway it’s a nice thing that you are doing a aid those poor folks…. I’m praying we send a couple of transports with stinging missile in them so that these proud strong folks can absolutely devastate the USSR… and destroy all incoming missiles being fired at their major utilities…. It was actually absolutely glorious when Russian having some of the pretty decent quality helicopters were pounding on the afghans and we carried in 300 on donkeys in three days of training 45% of those Russian helicopters were burning rubble…. Quite honestly if anyone in our present society aren’t feeling that they have a really great relationship with their lord and savior…they might want to rethink their thinking because we have two nuke subs just outside of range to turn Moscow into glass…. I’m really not quite sure that our current leader’s would be as good and ready as I am to send in a couple just to say hey bitch… that’s enough! But we should definitely be ready to get into the nuke show sooner then later! Now that the Russian people are really starting to stand up for world freedom and they know they are getting hustled…. And they are defection’s instead of fighting….the Russian people don’t want this war anymore then anyone else… too bad that we stopped our 11 teams and haven’t just shot him with a poison dart and ended the world’s problems… but they have a few hit teams here too so it would definitely need to be a very serious open up the Mountain in west Verginny and get our leaders and their families there.., before we go punching tickets…. I’m so pissed I’m 53 with horrible knees or I’d be more than happy to be headed to a tall building near the Russian capital to have a chance to be the guy that got to send a 308 through Putin we have allowed him to get away with entirely too much carnage without hitting all his personal assets with drone strikes…. I’m a hillbilly redneck…my diesel is $6.50 a gallon and it’s time for them sumbitches to start watching their backs… God what I would give to have that gentleman in a set of crosshairs with a spotter calling my windage !!! God Bless y’all and hoping that your Christmas was delightful! If you ever decide to make a weekend or shooting up 2” foam board then blowing more insulation in behind it in that raised ceiling area… I’ll volunteer to assist if there backstrap for the apple wood fire … we can always move your garbage can outside to get them up to 150! LMFFAO! That’s a very interesting property that you have there… very unique find!!! Beautiful place to keep working on your project’s to continue to make it better and better! Any son of a gun who will cook his brats in the ember’s trash can setup that he designed and built is okay with me buddy…. But please remember that several of us have 30 years in various trades and loads of knowledge and ability and there’s just something about this group of guys that link us up together on a very unique level and helping out a fella member for a couple days isn’t out of the question! I just took a very nice looking porter cable framing nailer from an old guy that needed his 372 rebuild immediately as one of his guy’s burnt her up…. So I opened up my parts box for the 372 parts and rebuilt that night for him because he had a decent job lined up…he had a hundred dollar bill and this framing nailer so if you ever need one for awhile it could be at the post office pretty quickly buddy. Even a smaller compressor will stoop 31/2” framing nails pretty easy! You could do 2x4’s on 24 and drywall it then mill some fake beams out and not only gain a lot of R-value but having some beams shoot into some pitched 2x4’s would actually add a little rustic look to that open higher ceiling area…. Slap some light cream paint over the drywall area’s in a couple of hours and it would look fabulous!!!! LMFFAO!

[@romper4444]

Doesn't get any more American than this guy eh lmao

[@HagenOne70]

I was hoping that your saws wouldn't "touch tips" during the timed event.

[@novicelumberjack]

I get that a lot! It would be fun if somehow I got a bit of kickback. The editing could be cool.

[@mr.somebody1493]

Knock on wood, my two Chinese zenoha clone saws are still running great.

[@novicelumberjack]

The Wemars have been very good for me.

[@mr.somebody1493]

@@novicelumberjack I have the Garwinner and the Auto Jare. The Garwinner is excellent quality, I suspect it is near identical to the Wemars. The Auto Jare is somewhat lesser quality but has taken everything i have thrown at it and it always starts. Both are worth every penny that i paid for them. and yes i do have bigger more expensive saws, but damn If i don't love running my Chinese clones.

[@jjm3254]

Great idea for the donation. Thank you.

[@garengtutorial8923]

Mantap bro 👍

[@Doc-Cole_Trickle-of-Chainsaws]

Go Wemars Go👍🆙BigGuy

[@jackfrosty79ify]

Bless you

[@zachdiehl3401]

Hell yeah thanks boedy

[@novicelumberjack]

Gotta port the Wemars now.

[@zachdiehl3401]

@@novicelumberjack I’ll be waiting for the video

[@oldcodger1929]

Those are crazy stupid numbers. Good job with what you had to work with.

[@novicelumberjack]

Thanks Codger!

[@cajun3197]

Hope it makes it to those guys in need good job

[@darrenwilson7688]

Great charity work Boedy!!!!

[@novicelumberjack]

Thank you kindly

[@Doc-Cole_Trickle-of-Chainsaws]

👍🆙BigGuy

[@timothybyrom5560]

I've got two of the no name saws ,supposedly 62cc. They BOTH run better than that,and I haven't touched either one. That's pathetic. I will say the red and black one runs better than the orange one.

[@crazyfeller5704]

👍

[@charlesjenks2710]

Great charity work name the channel you're sending it to it will help them

[@Doc-Cole_Trickle-of-Chainsaws]

Hey Louee dog!

[@novicelumberjack]

He says hello Doc!

[@11T872]

You did something wrong.

[@novicelumberjack]

You didn't watch all the video. Either that, or you don't know anything about port timing. And that's okay. Keep watching my channel. I talk about that stuff all the time.

[@11T872]

@@novicelumberjack what is fi of the piston?

[@novicelumberjack]

I don't know what you are talking about, "fi"? What do you mean "fi"?

[@11T872]

@@novicelumberjack fi is diameter

[@novicelumberjack]

@@11T872 okay, so the bore diameter is 45.24mm and the stroke is 34.22mm.

[@jimmylarge1148]

Shoulda gave it to the Russians

[@novicelumberjack]

Fuck russia.

[@jimmylarge1148]

@@novicelumberjack man, u sure are sadly misinformed and believing the tv I see…..not as smart as u think u are I see? U believe the lil hats are great people too?! 😂 But could u still compare the wemars to the pinkway 63 cc saws?!

[@novicelumberjack]

I just want you to understand who I am, and maybe a little bit about who you are. I have a large family that currently lives in Europe. I have been there personally about 10 different times, to five different countries. I have also deployed to many different theaters, sometimes during active conflicts. I have laid hands on explosives bigger than a Honda civic. And this is just some of the things I'm allowed to tell you about. Who the fuck are you? You think I'm the one being brainwashed? Hilarious. I've seen the women wailing in the streets because Russia invaded their country and killed their husbands and sons while they fought against the tyrant who is Putin. Where have you been? Your couch? What have you seen? Fox news? What have you done? Bitched about a war that you have zero concept of? Seriously? What the hell do you know about a goddamend thing that takes place outside of your living room? Have you even stepped foot outside your tri-state area? I know and love the people who are scared shitless that their country will be taken next by Putin. Back off. You know nothing about the subject, yet think you do because you watch some conservative opinion based entertainment. That is not a news source. Try going there and meeting the people directly affected by this war. When you have done that, then I might be inclined to listen to the rubbish that you are so quick to form a baseless opinion on.