Prepare to be amazed Broken trunnion shaft repaired by threading stronger than before #prepare #amazed #broken#trunnion #shaft #repaired #threading #stronger
Пікірлер: 33
@georgegonzalez24769 ай бұрын
Problem is, the result is very dubious. Nobody in this picture is a metallurgical or mechanical engineer, capable of designing a proper fix that will definitely not kill anyone. It’s much cheaper and secure to just replace the dang piece of steel.
@terrancel1089 ай бұрын
You've got a lot of praying to Allah for that to work but good luck.
@AmazingTechnology19 ай бұрын
Good job bro I like it ❤
@kerie-ok5vp8 ай бұрын
Wow 😲, amazing.
@khcreative89 ай бұрын
Good job bro
@urdeutscher65689 ай бұрын
Sehr gute Arbeit 👏👏👏👍
@mrkite11019 ай бұрын
Wow mechanics 1
@miguelmunozsanchez30449 ай бұрын
Very Goot exelent 👍👍✋
@dougdearinger58379 ай бұрын
Since the shaft is so short, why not just make a new one?
@user-jx2ye8cn5l9 ай бұрын
The problem is when you want a new detail,it is expensive.
@frostywelder12209 ай бұрын
This channel should be called Worlds Sketchiest Repairs.
@kennyalternative9 ай бұрын
There is alot of cry baby comments here. If you dont like the channel or the work they do, why watch. Not everybody can afford the American way of reairs, that is, let's make it as expensive as possible.
@algummarcosvinicius9 ай бұрын
I'm going to tell you this, they are "crying" because the way (and there are several) that they put the piece together is THE worst: it weakens the piece, it's more work, it lasts MUCH less because with the vibration the weld cracks and it gets full of rust inside (this just makes the vibration worse) and is sure to break fast. apart from that he used so little solder that it will be a surprise if it lasts 7 months. MORE EXPENSIVE, it will be when it breaks and you have to pay for another repair. There was another way to do it that is even cheaper and it would be much better than this "fix" they did.
@xenuno9 ай бұрын
@@algummarcosvinicius "he used so little solder" disqualifies you from any critiquing ...
@user-jx2ye8cn5l9 ай бұрын
@@algummarcosvinicius ,you were right.This is only get short time effort. But, the true problem is not solved.
@rasolfahry9 ай бұрын
كلكم اسطوات وماهرين في عملكم
@rustynail46769 ай бұрын
Why not repair the bearing surface while you have it in the lathe?
@nournour50869 ай бұрын
Very good...nice job❤❤🎉
@CNCMaster009 ай бұрын
Thanks
@josemanueljaramillosanchez75839 ай бұрын
Buen tornero😮🇻🇪
@mghaffarkhan98769 ай бұрын
Good
@danvanhoose67839 ай бұрын
5 minute garentee.what a joke.
@ronkilmer89919 ай бұрын
you all must be exceptional welders to avoide slag trap in those welds, and apparently you are using e8018 rods,
@victormontecinos37559 ай бұрын
No me digan que rectifico con la gallera por que midio con el micrometro.
@stevenhorne50899 ай бұрын
You've got to be kidding me? The guy almost stalled his machine just threading with it? What a joke.
@user-rd6ev9no6b9 ай бұрын
👍
@victormontecinos37559 ай бұрын
Com tendran los pies y piernas ademas la vista
@snowflakemelter11729 ай бұрын
" stronger than before " is a ridiculous lie.
@vladimirk41909 ай бұрын
Золотые руки👏👏👏🇷🇺🇷🇺🇷🇺👍👍👍
@camonsamuashvili65539 ай бұрын
но пустая голова. это до первой нагрузки.
@camonsamuashvili65539 ай бұрын
lesson on what not to do...
@manuelrando4849 ай бұрын
En España hay que ponerlo nuevo,😢 aunque no les dejen para comer.