Protecting The H2 Paintwork | DIY Stone Chip Film

[@sleepindragon179]

One thing I thought I'd never see on this channel is Chops using a hairdryer. Nice work thank you sir

[@LambChopRides]

haha brilliant :-)

[@darrenbutler160]

Fitted this to my super duke . Got back from a ride to see a tear right through it on the top of the tank where it had obviously taken a hit from a big stone . After a short period of crying I peeled off the film to reveal a tiny pin prick sized mark on the lacquer. This stuff works

[@LambChopRides]

great to hear it works!!!

[@simonbroom7459]

I've been using the 3m/venture shield for years on by bikes, its great stuff UV stable and cleans and polishes great. Little tip for the future spray the film as you take it off the backing paper it's less likely to get finger prints on it then. Great vid though Chops 👍

[@diamondheat9]

You have the patience of a saint. I am planning to get paint protection the day I pick up my NEW but getting someone to do it as I don't have a clean garage to DIY.

[@Weeem]

My Acra fitting is tight to the point where it makes contact with the swingarm when the suspension isn't loaded. I got a sheet of VentureShield or VentureGuard (whatever it's called) and cut a small section to put on the swingarm to protect the carbon on the Acra. It's been brilliant and in the last 6 years I only had to replace it once when some grit got under it and the Acra started to lift it off. Great stuff

[@LambChopRides]

Yes seems to be tough stuff, been for a few rides and no chips thus far!! Fingers crossed

[@AndyManCam]

Nice stickage Chops! I'd do the same for mine, if only R&G also had a time machine to go back to before the panels were already scratched and chipped!!

[@LambChopRides]

Thanks Andy!! Im only playing at this sticker stuff you are semi professional at it now!! haha. Yeah its well worth doing, Its too late for the GSXR to many chips on that now as it wont lay over chips well I wouldnt think..

[@highlandriders9696]

Very cool bit of kit Chops nd well demonstrated by one amateur for all amateurs. If I ever get round to changing bike I think I may invest in some of this

[@LambChopRides]

Thanks buddy 👍👍

[@BibTheBoulderTheOriginalOne]

My god you must have the patience of a saint.....Bib The Boulder would have given in before finishing the instructions....

[@themightyvinnie9825]

Bit late for paint protection!! 😂 But my god you must have patience. I'd have screwed it up in a ball and walked away!!!

[@MotoQuickShifter]

Thats absolutely what ive have just done ive just walked away half hanging off my h2 its fking hard , spent five hours faffing around with it and literally got no where with it lol

[@HalfdeadRider]

4:27 😂😂 Was not expecting that, back to the video 😎

[@MrAndyS]

I didn't even have the patience to watch it all let alone do it, well done.

[@LambChopRides]

haha :-)

[@grahamleigh7323]

Impressive chops... I’m sold 👏👏

[@reevesyrider6546]

I am sure it doesn’t but the sun always seems to be shining Henry’s world. Really enjoyed these two editions. Well done TMF. I am thinking of starting a channel soon. May be I will be approaching you for such an interview in the future.

[@amancalledjames9345]

I’ve got a kit to do mine...had it a couple of months and keep putting off doing it...suppose I’ll have to now. Thanks Chopsy!

[@LambChopRides]

Get it done James!! :0)

[@MotoMark55]

Lol at the David Mitchell clip Chops 🤣

[@skts2610]

I did my H2SXSE with that, piggin nightmare to do, worth it in the end though👍🏽

[@dannyracer25]

Chops you are brave. I paid my local bike shop to do mine thay said after i picked up bike " don't ask us to do that again it was a nightmare to do " that was on gsxr 1000 thanks Danny 😀

[@LambChopRides]

Its fine all you have to do is be patient and dont rush!

[@HippoDrones]

Nice job LCR, you have way more attention to detail and patience than I do, looks mint!

[@LambChopRides]

Thanks Pete 😁😁

[@NUTS13GTX]

Nice job. Does this affect the the self healing paint in anyway that comes out in the h2? Do you just polish as normal?

[@andyjackson5]

looks stunning mate! good job 👍🏻

[@bern1e74]

I bought a version of this before I picked up my Gixxer 1000R. Got it home and was the first thing I did. Spent 2 hours and it came out better than I’d expected. Like you, I did the dry finger print on the edge of one piece. Hardly noticeable and you wouldn’t find it if I drew you a map....... but I know it’s there and it fucks me off. 😂 Other than that, excellent stuff.

[@LambChopRides]

Yes I was impressed with it, told everyone I know to buy some now haha

[@davidhall370]

Love it when a fellow baldy handles a hair dryer.....🤔 the memories and flashbacks 🤣

[@LambChopRides]

Thats an official H2 accessory dont you know haha

[@christopherdevries1969]

Oh no.... Chops got shot 😱. 😂👍.

[@alrightdave6135]

Well done Chops. Looking forward to seeing your baby getting wheelied

[@anwarblnnn]

Hi mate, I have a question… After applying the paint protection skin, could we still polish our bike or it the protection going to change colour or move around?

[@Wazatsc]

what strength of rubbing alcohol did you use?

[@Shinysideup]

Nice job chops

[@valbarlis5226]

hey chop new subscriber here 😁RS always

[@MotoQuickShifter]

I honestly cant believe how frigging hard it is to do this ppf palaver , it took me 5 hours to do the side of the wind screen down to the nose and ive just bloody given up and left it half hanging off the H2 im so annoyed about it lol

[@kennethengstrom9261]

Nice job😅👍I have it on my beemer. Very good product, recommended👍

[@ReshardsAutomotiveWorkshop]

🤔...Heych-2... 🤷‍♂️ Chops is now the next Ghost Rider! 💀

[@2Wheel4Fun]

Whew...seems like a lot of work, but I'm sure it's well worth it...Good Luck with the project.

[@dawnrazrblade]

Great job 👍 I can’t even put a screen protector on my phone without getting bubbles or hairs under it then ripping it back off 😂

[@LambChopRides]

haha same!!

[@CosmicMidget]

I love my bikes but i just can't imagine myself doing this. It takes SO MUCH time and patience to put those small pieces all over the bike. Like H2R but i'm not going to buy one just because i don't want to be so obsessed with scratches on the paint.

[@essexhognose1808]

Why no tank protection? Any options to protect it like the front end?

[@HalfdeadRider]

It covers any parts likely to be stone chipped or clipped getting on and off, the front end is protected.

[@LambChopRides]

Yes only stone chip areas

[@jamesaaron2122]

Does anyone use that Q30 super protective spray ?

[@lynsmith1096]

Good video Lamb Chop don't think I would have the patience to do that

[@LambChopRides]

Yes need to take your time but its quite rewarding to do :-)

[@SkuStyle]

Chop's you should of said at the end of the video, '' that's a wrap! '' Cheese can please lol.

[@LambChopRides]

Haha dam yes!!! :-)

[@pistolpete6321]

Nice job, I don’t have the patience to do that myself!

[@Bornie205]

Cheers chops. Great film. How does it clean and wax up?

[@LambChopRides]

Yes cleans up fine Stephen, all still stuck down perfectly :-)

[@alanssnackbardailyrelaxati8155]

Admire your perseverance and the like chops. For me lifes to short for this fucking about. Still I appreciate your efforts 😎

[@davidhall370]

Never considered using this stuff but might think about it now. As I’m bald is there any chance of borrowing ‘your’ hair dryer?

[@dalehawkes1594]

You made that look reasonably easy Chops I’m going to give it a go bet I screw it up though did you get any quotes to have it done for you ??👍👍👍👍

[@LambChopRides]

Just take your time Dale its no too bad! :)

[@endasthenrik516]

Hmm interesting! Does it come with protection for the headlight too?

[@LambChopRides]

No unfortunately not

[@TheAegisClaw]

My issue with there is the edges get dirty after a while. Sometimes the film goes yellow as it ages too.

[@LambChopRides]

It is UV stable but guess after years and years you may have to change it...

[@chenderson4969]

What a complete piss about chops, more patient than me I can assure you! Tried to put a tank pad on my SV, that ended up in the bin after i flipped my lid. Enjoyed the new tunes haha!

[@windyrun7979]

Great job Chops! Nice of R&G to include all the equipment needed --- did they also provide the Abba Skylift ? Looks like a key piece of equipment :)

[@LambChopRides]

Yeah the Skylift does make it easier! when the bike stays on it haha

[@markgunn6680]

How does this affect the finish? Can you barely tell that it's on? I like the idea of this, but I wouldn't be seen dead with a screen protector on my mobile phone, so if it's anything like that then I think I'll give it a miss!

[@LambChopRides]

No you cant see it and bike still shines like it did without it!

A good installer does it with just three or four cuts with a heat gun, the more cuts the worst.

[@RichyVida]

Not a chance in hell, would I try that myself! I'm not talented enough! Man that is one incredible looking machine! See you on Sat, Chops....... Oh.... wait....... :-(

[@LambChopRides]

Haha thanks Richy, have a good one this weekend buddy 👍👍

[@thelikeablerider8800]

We like a good sticker set😜 scissors were a bit suspect mind lol

[@LambChopRides]

haha, honestly they are not mine baby!!

[@jefferywhite5636]

are you going to do the gsxr too?? it would be good for track days.....

[@LambChopRides]

It would but too many chips already... Dont think it will cover chips very well...

[@BN1960]

Cor, faff central dude!

[@R6Boss]

Thanks for this video just order for my r6

[@mikewatson361]

Are you available for hire 🤣🤣🤣🤣 🏍 looks great 👍

[@kevinhekers2380]

Maybe a ceramic coating on your tank for the h2

[@ApexMoto]

I can't put a screen protector on without having a fit over seeing bubbles. How the hell you done this I don't know. I take my hat off to you.

[@LambChopRides]

I cant do that either but this is much easier!! :-)

[@IanTed]

More patience than me😩👍

[@allyp6646]

Now that's on I would fuck up.

[@zogthewelk]

Chops, what has happened to the 3rd Husqy enduro vid?. I know they don`t get as many views, but some of us still enjoy some muck!.

[@LambChopRides]

There is a part 2 to come, it will happen :-)

[@Tenfx72]

Wow, I cant put stickers on the kids toys straight and without bubbles.

[@backwheelbob46rr]

Great vid mate I've got a rake of shit awaiting your professional touch 😎🍻

[@ragerider6283]

Lol. I'm rubbish at this stuff too, I get so angry as I always balls this type of stuff up. What a total pain in the arse this looks but totally get why you're doing it. Looks really good but I'm a bit surprised Kawasaki didn't do something like this as standard given the rarity of the paint. This is also illustrates the problem of owning a special & expensive bike. It's soul destroying to see it deteoriate & you can end up almost being scared to use it, which defeats the whole point of having it. Fight the urge chops, fight it lol! Love the ending too & he's right, it's A-tch not Hay-tch. ; )

[@kwak1k]

Music to cover up the swearing chops? 😉😂 You're very brave tackling that fella

[@LambChopRides]

haha yes :-)

[@nickarcher4775]

Great video.... really keen for you to review another Kawasaki the Z1000sx and compare it to the GSXS1000F you reviewed previously please.....

[@LambChopRides]

Yes would like to try one.... Will see if Wheels have one

[@nickarcher4775]

@@LambChopRides look forward to it thanks

[@Max-dj5qj]

Well done sir chops :) 👍. Now you can go fast as 😈

[@krp6147]

Good video chops, did I notice a KTM 690 smcr in the background 🤔

[@LambChopRides]

Yes well spotted!!

[@axellness]

Kawasucky

[@Paul-vl8zq]

I sprayed my bike the one on my photo it was under a rain cover awaiting my front wheel to come back from powdercoater I had a wheel on the front but no tyre I had wheel on the back with tyre and I heard a huge bang so I looked out window and it was my bike laying on floor.. My heart sank so I picked it up took cover off and OMG the only thing that was damaged was the bar end mirror no paint nothing. I was so lucky and now I don't use a rain cover lol 😂

[@LambChopRides]

Oh no devastating :( So glad you got away with it!!

[@michaeljkasnter]

Whats hard to believe is you only have 41k subs, RJ has over 1 million and your 10x more entertaining, all RJ does is ride around on a loud ass bike waving to people

[@LambChopRides]

Thanks Michael :-)

[@HUSKY7-1]

You'll sell it in less than one year, not worth the faff and the grubby edges. But you do love an accessory so crack on.....

[@gjkingston]

Not worth it at all - the bike will be sold in less than 24 months. Life's too short - ride it instead.

[@LambChopRides]

Yes but even more reason to install it if Im selling in 2 years, keep it nice for resale!

[@GaryFÓBrien]

Lol @ ‘haitch’

[@reophonic]

Tune in next week to watch Chops watching paint dry!!! Lol, you've got to much time on your hands Chops, nice job though👍🏼

[@LambChopRides]

haha now thats an idea for a video.... :-)

[@jamesaaron2122]

That looks painful

[@Bass.Player]

You need a bigger garage...

[@andrewmcglashan5041]

Sponge on paint

[@grenphelps7455]

Chuck that sponge in the bin....and get yourself a Microfibre wash mitt, if your gonna do it, do it right....

[@shaun9107]

Do not try this at home fuck sake

[@Bornie205]

Cheers chops. Great film. How does it clean and wax up?