R450 AVR HIGH CIRCULATING CURRENT when synch, how to fix benzblogs

[@ades_panel]

Assalamualaikum.. Thank you Sir.. I have same problem last night.. I will try to adjust the stability in 1% and the drop in 25%, I havent try it before.. 😊😊

[@benzblogsVlogs]

Welcome

[@ELECTRICALPOWERGENERATION]

What is role of trim 🤔 in avr

[@benzblogsVlogs]

Trim meaning its a small adjustment depend on what adjustment you need

[@МарянМірило]

Hi. Could you help me with this question? I am preparing to synchronize two generators. For this, it was advised to use avr Leroy Somer R450. Do I need to connect the analog output of the DSE8610 panel (0-5V) instead of a potentiometer (on the 1k ohm circuit)?

[@benzblogsVlogs]

If your doing synchro thin u need analog

[@МарянМірило]

@@benzblogsVlogs so i can't use for synchro avr R450?

[@benzblogsVlogs]

@@МарянМірило ys

[@МарянМірило]

@@benzblogsVlogs thanks sir!

[@benzblogsVlogs]

@@МарянМірило wc

[@ricmarjohnmatas7980]

Good job sir benz..

[@benzblogsVlogs]

Sir salamat bless you

[@ELECTRICALPOWERGENERATION]

In case if no droop CT

[@benzblogsVlogs]

If no droop ct its good and easy to calibrate

[@mengsteabberhane-wt1yo]

Hi my dear can you tell me the droop transformer rating or specialisations for 1000kilowatt generator having R-450 AVR? Thanks

[@benzblogsVlogs]

Droop is always half of your primary city value

[@mohammedal-qadi104]

Great job sir. What is the relation between AVR andcirculating current ? What if we don't have droop CT will we face the same problem of circulating current ? Thank you in advance ☺

[@benzblogsVlogs]

Depend on cerculating current nit means that if u have droop ct can posible happen dpend on how you do the the setpoints and calibration of your avr drrop ct is for protection for your alternator itself where it is connexted to avr where avr can understand the curent status , voltage, freq

[@benzblogsVlogs]

If no drrop ct protection is not there its only refer to the module itself for protection if module fail no other protextion will occur

[@benzblogsVlogs]

With or without droop it work and also cerculating may happen if wrong calibration, connection , and config.

[@christianluwawu8701]

Bonjour Mr esk vous donne aussi des formations sur ça pour le groupe électrogène. La synchronisation si vous pouvez mes formé sur ça c'est vraiment pour moi tre tre important Merci

[@benzblogsVlogs]

The parameter you need to do a synchro must know the speed,voltage should be same same line connection same color coding you must do the proper calibration to the module from voltage and speed and biasing

[@iroshanlahiru609]

hello R450 which connection are connect to Module (like Stamford Avr A1, A2)

[@benzblogsVlogs]

What you mean sir for the module volatge control?

[@benzblogsVlogs]

Same the the connection is the analog potentiometer same

[@iroshanlahiru609]

@@benzblogsVlogs would u plz tell me r450 ANALOG 5v connection control by dse module i could nt find the Avr control wire r450 for synchronize

[@ahmedfarouk184]

Nice 👍👍👍

[@edmunddeguzman3153]

Sir yung dalawang genset n no sycrhinize pero yung isa leading yung isa lagging tapos my circulating current negative yung leading kw at kvar at positive yung lagging salamat

[@benzblogsVlogs]

Sir pag leading sir check mo lang ct mo may mali yan jan

[@edmunddeguzman3153]

@@benzblogsVlogs ct sir papuntang Woodward or s controller catterpilar sir

[@benzblogsVlogs]

Papontang module

[@christianluwawu8701]

Félicitations

[@benzblogsVlogs]

Just adjust the stability of the avr so fluctuation is gone but before you do check the speed and frequency is stable okay

[@josephgammad2338]

Sir 2genset na ka sync pero wala pang load tapos ung amp ay 150 at un isang genset ay 150amp din at pareho 0 load minsan negative panga ano kaya problem nito

[@benzblogsVlogs]

Sir naka synch tama ano po ang avr na gamit nyo

[@benzblogsVlogs]

Ano po yung nigative kw or amps

[@christianluwawu8701]

G travail sur FG Wilson a Congo Kinshasa notre société est unicompex Congo

[@jaimetemplo3726]

Good day sir baka naman pwedeng makita ang load bank mo kasi napansin ko ang main breaker mo may nakakabit na cable sa neutral

[@benzblogsVlogs]

Sir pag sync my dalawang klasi my totalizing or my direct cabling